HVU with HAS/HAS-E rod adhesive anchor
Rotary hammer . TE 2 – TE 16 . TE 40 – TE 70 . ... Setting instruction . Dry and water-saturated concrete, hammer drilling. For detailed information on installation see instruction for use given with the package of the product. ... drill bit 0 d [mm] 10 . 12 . 14 . 18 . 24 . 28 . 30 . 35 . Effective anchorage and drill hole depth h ef [mm ...
Tags:
Rotary, Drill, Hammer, Rotary hammer
Information
Domain:
Source:
Link to this page:
Please notify us if you found a problem with this document:
Documents from same domain
KB-TZ2 TECHNICAL GUIDE
www.hilti.comKB-TZ2 Technical uide April 2021 5 Table 4 - Allowable Hilti carbon steel KB-TZ2 strength in uncracked concrete for hammer drill and core drill installations 1,2,3,4 Nominal anchor
Hilti HIT-HY 200 with HIT-V
www.hilti.comAnchor rods HIT-V GR / -HCR) are available in variable length MIO M12 TE 16 M16 M20 M24 TE 40 M27 - TE 70 M30 compressed air gun or blow out pump, set of cleaning brushes, dispenser Drill hole to the required embedment depth with an appropriately sized Hilti TE-CD Or TE-YD hollow drill bit with Hilti vacuum attachment. This drilling
With, Anchor, Rods, Hilti, Anchor rods, Hilti hit hy 200 with hit
Hilti HIT-HY 200 with rebar
www.hilti.comHilti HIT-HY 200 with rebar Benefits - suitable for cracked and non- cracked concrete C 20/25 to C 50/60. - Approved automatic cleaning with the use of the hollow drill-bit high loading capacity, excellent handling HY 200-R version with extended curing time for rebar applications small edge distance and anchor spacing possible
Page 1/8 Safety Data Sheet acc. to ISO 11014 - Hilti USA
www.hilti.comPage 2/8 Safety Data Sheet acc. to ISO 11014 Printing date 05/19/2015 Version number 5 Reviewed on 05/19/2015 (Contd. of page 1) 40.2.7 H319 Causes serious eye irritation.
Sheet, Data, Safety, Pages, Page 1, Hilti, 8 safety data sheet acc
Hilti. Outperform. Outlast.
www.hilti.comSelector Guide Through-Penetration Joint Reference Data Firestop Mortar (CP 637) Product description ... Concrete and masonry assemblies Expansion on setting (approx.)Walls and floors rated up to 4 hours ... Mix ratio (recommended, mortar to water):
ICC-ES Evaluation Report ESR-2269 - Hilti
www.hilti.com1.0 EVALUATION SCOPE Compliance with the following codes: 2018, 2015, and 2012 International Building Code ® (IBC) 2018, 2015, and 2012 International Residential Code® (IRC) For evaluation for compliance with codes adopted by the Los Angeles Department of Building and Safety (LADBS), see ESR-2269 LABC and LARC Supplement.
Report, Evaluation, Hilti, 2269, Icc es evaluation report esr 2269
HILTI TECHNICAL BULLETIN
www.hilti.comMar 04, 2018 · )n ≤ 1, where n=5/3 for 3/8- and 1/2-inch diameters (No. 3 and No. 4 rebar) and n=1 for 5/8 and 3/4-inch diameter or No. 5 and No. 6 rebar. 9 The critical spacing, s cr, is the smallest anchor spacing where full load values may be used. The minimum spacing, s min, is the minimum anchor spacing for which values are
HIT-RE 500 V3 - Hilti
www.hilti.comSafety information for 2-Component-products 18/06/2020 US-OSHA - en 2/27 IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. If skin irritation or rash occurs: Get medical advice/attention. If eye irritation persists: Get medical advice/attention.
OPENINGS IN COMPOSITE FLOOR DECKS - Hilti
www.hilti.comin-situ reinforced concrete topping. The decking not only acts as a permanent formwork to the concrete, but also provides sufficient shear bond with the concrete so that, when the concrete has cured, the two materials act together compositely to resist the loads on the deck. Openings in floor decks are a common part of any building.
HIT-1 ADHESIVE ANCHORING SYSTEM - Hilti
www.hilti.comHIT-1 ADHESIVE ANCHORING SYSTEM Technical Supplement PRODUCT DESCRIPTION Hilti HIT-1 is a hybrid adhesive mortar combining resin, hardener, cement, and water. It’s formulated for fast curing and easy installation in a wide range of concrete and masonry base materials with temperatures ranging from 32°F (0°C) up to 95°F (35°C).
Related documents
The DIY STEN Gun - noblogs.org
elcombate.noblogs.organgle until the drill bit wanders back to the centre. The resulting hole can then be levelled flat using a second 10mm drill bit modified by removing it's tip using an angle grinder. A slight bevel is made around the hole using a 16mm+ drill bit or rotary tool grinding bit.
Metal Working Processes, Tools, and Machines
stoves.bioenergylists.org•Hammer and chisel •Hand and power snips •Hand and power nibblers •hand notchers •Hand and foot lever notchers •Slotted angle shear •Angle shear, notcher •Circle cutter •Circle shear •Hand lever shear •Foot shear •Rotary can openers •Drum deheader •Angle grinder •Hand and power saws (hack, jig, circular, chop, …)