Example: quiz answers
INSTALLATION MANUAL Model CLS (Single-Lamp Cathode …
INSTALLATION MANUAL Model CLS (Single-Lamp Cathode Light Strip) ... Lutron is preferred. Primary wiring for these luminaires must contain three (3) conductors, plus a ground wire. ... and black ballast leads must be wired together, and then to the switched, hot primary circuit.
Tags:
Information
Domain:
Source:
Link to this page:
Related documents
Power Boosters and 120 V Interfaces - Lutron Electronics
files.lutron.comPower Boosters and 120 V Interfaces INSTAllATION NOTES: For models NGRX-PB-WH, GRX-FDBI-16A-120, and ... mum load requirements for the controlling device . See pgs. 109-110, 113-114, 117. ... fluorescent dimming ballast powered by 100-277 V . Ballast must supply 0-10 V signal . …
Discharge Lamps and Ballasts - acuitybrandslighting.com
www.acuitybrandslighting.comLutron Electronics Co., Inc. ..... 800-523-9466 ... be disposed of in accordance with local requirements. ... Discharge Lamps and Ballasts. PSG9 LAMPS AND BALLASTS www.AcuityBrandsLighting.com 707 from nominal. As a result, depending on the type of ballast being used, H.I.D. lamp wattage may
MaestroR 0–10 V Dimmer Sensor - Alcon Lighting
alconlighting.comrequirements • Adjustable timeout (1, 5, 15, or 30 minutes) ... • please see Lutron P/N 3697738 A 0–10 V- electronic fluorescent ballasts or LED ... and whose inrush current does not exceed NEMA410 standards for electronic ballast/driver loads of 8 A steady state current. • 50 mA max sink current • Controls up to 25 ballasts or ...
XEB-7-B-LM Series - Barron Lighting Group
barronltg.comXEB-7-B-LM Series FLUORESCENT EMERGENCY BALLAST SPEC FICATIONS ARE SUBJECT ... and is UL Listed for factory installation or retrofit applications. The XEB-7-B-LM has a minimal initial output of ... Emergency Lighting Requirements • Painted, steel case • 120/277V dual primary, 60Hz input CASE DIMENSIONS Length 9.4"
Easy to BALLASTS OR T5, install - images.philips.com
images.philips.com3.5 Ballast shall comply with the requirements of the Federal Communications Commission (FCC) rules and regulations, Title 47 CFR part 18, Non-Consumer equipment. 3.6 Ballast shall comply with UL Type CC rating. 3.7 Ballast shall comply with NEMA 410 for in-rush current limits.
Power Pack PP Series Installation Instructions
helenmitchell.comPOWER PACKS PP SERIES Installation Instructions Please Read DESCRIPTION PP and UPP Series Power Packs provide both the 24 V- power supply to operate Lutron ® occupancy sensors, as well as the 20 A line voltage relay to control the load, in one compact housing.
GRAFIK RASeries Control Units - Electric Supplies Online
site.electricsuppliesonline.comLutron’s liability on any claim for damages arising out of or in connection with the manufacture, sale, installation, delivery, or use of the unit shall never exceed the purchase price of the unit.
featuring Lutron’s microWATT Lighting Controller
virtuslife.com2. Control, Sensor and Input Signal Functions . microWATT intelligently coordinates one or all, in any combination. Manual Dimming Control. Dim light levels to suit individual requirements.
CENTRAL(CAROILNACOMMUNITY(COLLEGE …
www.cccc.edua. Warranty Information b. System Start-up Information c. Installation Guide d. Set-up and Programming Guide 2. Electronic format to be available on Lighting Control System manufacturer website.
SECTION 260933 CENTRAL DIMMING CONTROLS Eaton …
www.cooperindustries.comLighting control system must be protected from dust and sprays during installation. 1.7 WARRANTY A. Provide manufacturer’s warranty covering 5 year parts to repair and replace defective equipment.
Related search queries
Boosters and 120 V Interfaces, Lutron, Boosters and 120 V Interfaces INSTAllATION, Requirements, Ballast, Discharge Lamps and Ballasts, MaestroR 0–10 V Dimmer Sensor, XEB-7-B-LM Series, Installation, Easy to BALLASTS OR T5, install, PP SERIES Installation Instructions, GRAFIK RASeries Control Units, SECTION 260933 CENTRAL DIMMING CONTROLS Eaton