IR Receiver Modules for Remote Control Systems - …

1 , , semiconductors Rev. , 12-Apr-181 Document Number: 81743 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT Receiver Modules for Remote Control SystemsDESIGN SUPPORT TOOLSMECHANICAL DATAP inning for , , :1 = OUT, 2 = GND, 3 = VS FEATURES Very low supply current Photo detector and preamplifier in one package Internal filter for PCM frequency Supply voltage: V to V Improved immunity against ambient light Insensitive to supply voltage ripple and noise Material categorization: for definitions of compliance please see products are miniaturized receivers for infrared Remote Control Systems . A PIN diode and a preamplifier are assembled on a lead frame, the epoxy package contains an IR filter.

2 The demodulated output signal can be directly connected to a microprocessor for series devices are optimized to suppress almost all spurious pulses from energy saving lamps like CFLs. AGC3 may also suppress some data signals if continuously series are provided primarily for compatibility with old AGC1 designs. New designs should prefer the series containing the newer AGC3. The series contain a very robust AGC5. This series should only be used for critically noisy components have not been qualified according to automotive logo to get startedAvailableModelsPARTS TABLEAGCLEGACY, FOR SHORT BURST Remote CONTROLS (AGC1)NOISY ENVIRONMENTS ANDSHORT BURSTS (AGC3)VERY NOISY ENVIRONMENTSAND SHORT BURSTS (AGC5)Carrier frequency30 kHzTSOP38130 TSOP38330 TSOP3853033 kHzTSOP38133 TSOP38333 TSOP3853336 kHzTSOP38136 TSOP38336 (1)(6)TSOP3853638 kHzTSOP38138 TSOP38338 (2)(3)(4)(5)TSOP3853840 kHzTSOP38140 TSOP38340 TSOP3854056 kHzTSOP38156 TSOP38356 TSOP38556 PackageMinicastPinning1 = OUT, 2 = GND, 3 = VSDimensions (mm) W x H x DMountingLeadedApplicationRemote controlBest choice for(1) MCIR (2) Mitsubishi (3) RECS-80 Code (4) r-map (5) XMP-1, XMP-2 (6) , , semiconductors Rev.

3 , 12-Apr-182 Document Number: 81743 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT DIAGRAMAPPLICATION CIRCUITNote Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect the device reliabilityTYPICAL CHARACTERISTICS (Tamb = 25 C, unless otherwise specified)Fig. 1 - Output Active LowFig. 2 - Pulse Length and Sensitivity in Dark Ambient30 k 231 Demo-passAGCI nputPINB anddulatorControl circuit16833-13C1IR receiverGNDC ircuit CR1+ VSGNDT ransmitterwithTSAL xxxxVSVO17170-11 OUTR1 and C1 recommended to reduce supply ripple for VS < VABSOLUTE MAXIMUM RATINGSPARAMETERTEST CONDITIONSYMBOLVALUEUNITS upply to +6 VSupply currentIS3mAOutput to (VS + )VOutput currentIO5mAJunction temperatureTj100 CStorage temperature rangeTstg-25 to +85 COperating temperature rangeTamb-25 to +85 CPower consumptionTamb 85 CPtot10mWSoldering temperaturet 10 s, 1 mm from caseTsd260 CELECTRICAL AND OPTICAL CHARACTERISTICS (Tamb = 25 C, unless otherwise specified)PARAMETERTEST currentEv = 0, VS = = 40 klx, distanceEv = 0, test signal see Fig.

4 1,IR diode TSAL6200, IF = 50 mAd-24-mOutput voltage lowIOSL = mA, Ee = mW/m2, test signal see Fig. 1 VOSL--100mVMinimum irradiancePulse width tolerance:tpi - 5/fo < tpo < tpi + 6/fo, test signal see Fig. 1Ee irradiancetpi - 5/fo < tpo < tpi + 6/fo, test signal see Fig. 1Ee of half transmission distance 1/2- 45- EeTtpi *)tVOVOHVOLtpo 2)t14337 Optical Test Signal(IR diode TSAL6200, IF = A, N = 6 pulses, f = f0, t = 10 ms)Output Signaltd 1)1) 3/f0 < td < 9/f02) tpi - 4/f0 < tpo < tpi + 6/f0*) tpi 6/f0 is recommended for optimal 10 000 100 000Ee - Irradiance (mW/m )tpo - Output Pulse Width (ms)20771 = 950 nm,optical test signal, Fig. 1 Output pulse widthInput burst , , semiconductors Rev. , 12-Apr-183 Document Number: 81743 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE.

5 THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT 3 - Output FunctionFig. 4 - Output Pulse DiagramFig. 5 - Frequency Dependence of ResponsivityFig. 6 - Sensitivity in Bright AmbientFig. 7 - Sensitivity vs. Supply Voltage DisturbancesFig. 8 - Max. Envelope Duty Cycle vs. Burst LengthEetVOVOHVOLt600 s600 st = 60 mstontoff94 8134 Optical Test SignalOutput Signal, (see Fig. 4) 000Ee - Irradiance (mW/m2)ton, toff - Output Pulse Width (ms)20759 = 950 nm,optical test signal, Fig. 3 - Relative Frequency16925f = f0 5 % f(3 dB) = f0/10Ee - Relative - Ambient DC Irradiance (W/m2)Ee min. - Threshold Irradiance (mW/m2)Correlation with ambient light sources:10 W/m2 = klx (std. illum. A, T = 2855 K)10 W/m2 = klx (daylight, T = 5900 K) Wavelength of ambient illumination: = 950 nm207570 1 10 100 1000 Ee min.

6 - Threshold Irradiance (mW/m2) VS RMS - AC Voltage on DC Supply Voltage (mV) f = f0f = 30 kHzf = 10 kHzf = 100 Hz 20406080100120 Burst Length (Number of Cycles/Burst)Max. Envelope Duty Cycle22180-7f = 38 kHz,Ee = 2 mW/m , , , , semiconductors Rev. , 12-Apr-184 Document Number: 81743 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT 9 - Sensitivity vs. Ambient TemperatureFig. 10 - Relative Spectral Sensitivity vs. WavelengthFig. 11 - Horizontal DirectivityFig. 12 - Vertical DirectivityFig. 13 - Sensitivity vs. Supply min. - Threshold Irradiance (mW/m2) Tamb - Ambient Temperature ( C) ( )rel - Relative Spectral Sensitivity - Wavelength (nm)115094 30 10 20 40 50 60 70 80 - Relative Transmission Distance19259 30 10 20 40 50 60 70 80 Relative Transmission 1 2 3 4 5 Ee min.

7 - Sensitivity (mW/m2) VS - Supply Voltage (V) , , semiconductors Rev. , 12-Apr-185 Document Number: 81743 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT DATA FORMATThis series is designed to suppress spurious output pulses due to noise or disturbance signals. The devices can distinguish data signals from noise due to differences in frequency, burst length, and envelope duty cycle. The data signal should be close to the device s band-pass center frequency ( 38 kHz) and fulfill the conditions in the table a data signal is applied to the product in the presence of a disturbance, the sensitivity of the Receiver is automatically reduced by the AGC to insure that no spurious pulses are present at the Receiver s examples which are suppressed are: DC light ( from tungsten bulbs sunlight) Continuous signals at any frequency Strongly or weakly modulated patterns from fluorescent lamps with electronic ballasts (see Fig.)

8 14 or Fig. 15) Fig. 14 - IR Disturbance from Fluorescent LampWith Low ModulationFig. 15 - IR Disturbance from Fluorescent LampWith High ModulationNote For data formats with long bursts (more than 10 carrier cycles) please see the datasheet for , Title1st line2nd line2nd lineIR Signal AmplitudeTime (ms)1692110100100010000-60-40-2002040051 01520 Axis Title1st line2nd line2nd lineIR Signal AmplitudeTime (ms) burst length6 cycles/burst6 cycles/burst6 cycles/burstAfter each burst of length A gap time is required of6 to 70 cycles 10 cycles6 to 35 cycles 10 cycles6 to 24 cycles 10 cyclesFor bursts greater than a minimum gap time in the data stream is needed of70 cycles> x burst length35 cycles> 6 x burst length24 cycles> 25 msMaximum number of continuous short bursts/second200020002000 MCIR codeYesPreferredYesRCMM codeYesPreferredYesXMP-1, XMP-2 codeYesPreferredYesSuppression of interference from fluorescent lampsMild disturbance patternsare suppressed (example:signal pattern of Fig.

9 14)Complex disturbance patternsare suppressed (example:signal pattern of Fig. 15)Critical disturbancepatterns are suppressed, highly dimmed , , semiconductors Rev. , 12-Apr-186 Document Number: 81743 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT DIMENSIONS in ( ) max.( ) (4) : : 12; to DINtechnical drawingsNot indicated to lerances areaR 2R 219009 Legal Disclaimer Revision: 01-Jan-20211 Document Number: 91000 Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, vishay ), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product.

10 To the maximum extent permitted by applicable law, vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on vishay s knowledge of typical requirements that are often placed on vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer s responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application.