IR Receiver Modules for Remote Control Systems - Vishay

1 , Vishay Semiconductors IR Receiver Modules for Remote Control Systems FEATURES. Very low supply current Photo detector and preamplifier in one package Internal filter for PCM frequency Supply voltage range: V to V. Improved immunity against modulated light 4 sources 3 Insensitive to supply voltage ripple and noise 2. 1 16797 Capable of side or top view Material categorization: for definitions of compliance please see DESIGN SUPPORT TOOLS click logo to get started DESCRIPTION. Models The series are miniaturized SMD IR Receiver Available Modules for infrared Remote Control Systems . A PIN diode and a preamplifier are assembled on a leadframe, the epoxy MECHANICAL DATA. package contains an IR filter. Pinning: The demodulated output signal can be directly connected to 1 = GND, 2 = , 3 = VS, 4 = OUT a microprocessor for decoding. The series devices are optimized to suppress ORDERING CODE.

2 Almost all spurious pulses from energy saving lamps like Taping: CFLs. The AGC4 used in the may suppress - top view taped some data signals. The series are provided - side view taped primarily for compatibility with old AGC2 designs. New designs should prefer the series containing the newer AGC4. These components have not been qualified according to automotive specifications. PARTS TABLE. LEGACY, FOR RECOMMENDED FOR. AGC. LONG BURST Remote CONTROLS (AGC2) LONG BURST CODES (AGC4). 30 kHz TSOP36230 TSOP36430. 33 kHz TSOP36233 TSOP36433. 36 kHz TSOP36236 TSOP36436 (1)(2)(3). Carrier frequency 38 kHz TSOP36238 TSOP36438 (4)(5). 40 kHz TSOP36240 TSOP36440. 56 kHz TSOP36256 TSOP36456 (6)(7). Package Panhead Pinning 1 = GND, 2 = , 3 = VS, 4 = OUT. Dimensions (mm) W x H x D. Mounting SMD. Application Remote Control Best choice for (1) RC-5 (2) RC-6 (3) Panasonic (4) NEC (5) Sharp (6) r-step (7) Thomson RCA.

3 Rev. , 24-Sep-2018 1 Document Number: 82568. THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT. ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT , Vishay Semiconductors BLOCK DIAGRAM APPLICATION CIRCUIT. 3. 17170-11. VS R1. 30 k Transmitter IR Receiver with VS + VS. 4 TSAL xxxx C1. Circuit Band Demo - OUT. Input AGC C. pass dulator OUT. VO. 1; 2 GND GND. PIN Control circuit GND. R1 and C1 recommended to reduce supply ripple for VS < V. 16839. ABSOLUTE MAXIMUM RATINGS. PARAMETER TEST CONDITION SYMBOL VALUE UNIT. Supply voltage (pin 3) VS to +6 V. Supply current (pin 3) IS 3 mA. Output voltage (pin 4) VO to (VS + ) V. Output current (pin 4) IO 5 mA. Junction temperature Tj 100 C. Storage temperature range Tstg -25 to +85 C. Operating temperature range Tamb -25 to +85 C. Power consumption Tamb 85 C Ptot 10 mW.

4 Note Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect the device reliability ELECTRICAL AND OPTICAL CHARACTERISTICS (Tamb = 25 C, unless otherwise specified). PARAMETER TEST CONDITION SYMBOL MIN. TYP. MAX. UNIT. Ev = 0, VS = V ISD mA. Supply current Ev = 40 klx, sunlight ISH - - mA. Supply voltage VS - V. Ev = 0, test signal see Fig. 1, Transmission distance IR diode TSAL6200, d - 24 - m IF = 50 mA. IOSL = mA, Ee = mW/m2, Output voltage low VOSL - - 100 mV. test signal see Fig. 1. Pulse width tolerance: Minimum irradiance tpi - 5/fo < tpo < tpi + 6/fo, Ee min.

5 - mW/m2. test signal see Fig. 1. tpi - 5/fo < tpo < tpi + 6/fo, Maximum irradiance Ee max. 30 - - W/m2. test signal see Fig. 1. Angle of half transmission Directivity 1/2 - 50 - . distance Rev. , 24-Sep-2018 2 Document Number: 82568. THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT. ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT , Vishay Semiconductors TYPICAL CHARACTERISTICS (Tamb = 25 C, unless otherwise specified). Ee Optical Test Signal (IR diode TSAL6200, IF = A, 30 pulses, f = f0, t = 10 ms). ton ton, toff - Output Pulse Width (ms). t tpi * toff T. * tpi 10/f0 is recommended for optimal function Output Signal VO 16110. = 950 nm, 1) 7/f0 < td < 15/f0 optical test signal, Fig. 3. VOH. 2). tpi - 5/f0 < tpo < tpi + 6/f0 0. 1 10 100 1000 10 000. VOL. td 1) tpo 2) t 20759 Ee - Irradiance (mW/m2). Fig. 1 - Output Active Low Fig.

6 4 - Output Pulse Diagram Output pulse width Ee - Relative Responsivity tpo - Output Pulse Width (ms). Input burst length = 950 nm, f = f0 5 %. optical test signal, Fig. 1 f(3 dB) = f0/10. 0 1 10 102 103 104 105 20752 Ee - Irradiance (mW/m2) 16925 f/f0 - Relative Frequency Fig. 2 - Pulse Length and Sensitivity in Dark Ambient Fig. 5 - Frequency Dependence of Responsivity Optical Test Signal Ee min. - Threshold Irradiance (mW/m2). Ee Correlation with ambient light sources: 10 W/m2 = klx (std. illum. A, T = 2855 K). 10 W/m2 = klx (daylight, T = 5900 K). Wavelength of ambient t 600 s 600 s illumination: = 950 nm t = 60 ms 94 8134. Output Signal, (see Fig. 4) VO. VOH. 0. VOL 1 10 100. t on t off t Ee - Ambient DC Irradiance (W/m2). 20757. Fig. 3 - Output Function Fig. 6 - Sensitivity in Bright Ambient Rev. , 24-Sep-2018 3 Document Number: 82568. THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE.

7 THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT. ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT , Vishay Semiconductors Axis Title Ee min. - Threshold Irradiance (mW/m2). 10000. S( )rel. - Relative Spectral Sensitivity f = f0 f = 30 kHz 1000. f = 10 kHz 2nd line 1st line 2nd line f = 100 Hz 100. 0 1 10 100 1000 0 10. VS RMS - AC Voltage on DC Supply Voltage (mV) 750 850 950 1050 1150. 21425 - Wavelength (nm). Fig. 7 - Sensitivity vs. Supply Voltage Disturbances Fig. 10 - Relative Spectral Sensitivity vs. Wavelength 0 10 20 . 30 . Max. Envelope Duty Cycle 40 . 50 . 60 . 70 . 80 . f = 38 kHz, Ee = 2 mW/m . 0. 0 20 40 60 80 100 120 0 Burst Length (number of cycles/burst) 16801 d rel - Relative Transmission Distance Fig. 8 - Maximum Envelope Duty Cycle vs. Burst Length Fig. 11 - Horizontal Directivity Ee min. - Threshold Irradiance (mW/m2). Ee min. - Sensitivity (mW/m2).

8 0 -30 -10 10 30 50 70 90 1 2 3 4 5. Tamb - Ambient Temperature ( C) VS - Supply Voltage (V). Fig. 9 - Sensitivity vs. Ambient Temperature Fig. 12 - Sensitivity vs. Supply Voltage Rev. , 24-Sep-2018 4 Document Number: 82568. THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT. ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT , Vishay Semiconductors SUITABLE DATA FORMAT Axis Title This series is designed to suppress spurious output pulses 7 10000. due to noise or disturbance signals. The devices can 6. distinguish data signals from noise due to differences in frequency, burst length, and envelope duty cycle. The data 5. IR Signal Amplitude signal should be close to the device's band-pass center 1000. frequency ( 38 kHz) and fulfill the conditions in the table 2nd line 4. 1st line 2nd line below. 3. When a data signal is applied to the product in the presence of a disturbance, the sensitivity of the Receiver is 100.

9 2. automatically reduced by the AGC to insure that no spurious pulses are present at the Receiver 's output. 1. Some examples which are suppressed are: 0 10. DC light ( from tungsten bulbs sunlight) 0 5 10 15 20. Continuous signals at any frequency 16920 Time (ms). Strongly or weakly modulated noise from fluorescent Fig. 13 - IR Disturbance from Fluorescent Lamp lamps with electronic ballasts (see Fig. 13 or Fig. 14) With Low Modulation Axis Title 40 10000. IR Signal Amplitude 20. 1000. 0. 2nd line 2nd line 1st line -20. 100. -40. -60 10. 0 5 10 15 20. 16921 Time (ms). Fig. 14 - IR Disturbance from Fluorescent Lamp With High Modulation Minimum burst length 10 cycles/burst 10 cycles/burst After each burst of length 10 to 70 cycles 10 to 35 cycles a minimum gap time is required of 10 cycles 10 cycles For bursts greater than 70 cycles 35 cycles a minimum gap time in the data stream is needed of > 4 x burst length > 10 x burst length Maximum number of continuous short bursts/second 1800 1500.

10 NEC code Yes Preferred RC5 / RC6 code Yes Preferred Thomson 56 kHz code Yes Preferred Sharp code Yes Preferred Mild disturbance patterns Complex and critical disturbance patterns Suppression of interference from fluorescent lamps are suppressed (example: are suppressed (example: signal pattern signal pattern of Fig. 13) of Fig. 14 or highly dimmed LCDs). Notes For data formats with short bursts please see the datasheet for , , For Sony 12, 15, and 20 bit IR codes please see the datasheet of TSOP36S40F. Rev. , 24-Sep-2018 5 Document Number: 82568. THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT. ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT , Vishay Semiconductors PACKAGE DIMENSIONS in millimeters Pick and place area. TT taping A. ( ). 1 4. ( ). 4x 3 x = 4. A. Not indicated tolerances Pick and place area.