LED Driver • Constant Voltage + Constant Current • …

1 TRC ELECTRONICS, INC. ELECTRONICS, exceptional customer service since 1982 File Name:ELG-150-SPEC 2020-04-0884~150W Constant Voltage + Constant Current LED DriverELG-150 series C C A Dx { IP67IP65 IS 15885(Part 2/Sec13)R-41027766(for 12/12B/12DA/24/24B/24DA/36A/42/42A/48A/5 4 only) LED Driver Constant Voltage + Constant Current 150W MEAN WELL ELG-150 SeriesTRC ELECTRONICS, INC. ELECTRONICS, exceptional customer service since 1982 ELG-150 seriesSPECIFICATIONMODELOUTPUTVOLTAGE RANGE RANGEPOWER FACTOREFFICIENCY (Typ.)AC CURRENTINPUTINRUSH Current (Typ.)LEAKAGE CURRENTWORKING TEMP. WORKING HUMIDITYSTORAGE TEMP., HUMIDITYTEMP.}

2 COEFFICIENTVIBRATIONOVER TEMPERATUREOVER VOLTAGE1600ms, 80ms/115 VAC 500ms, 100ms/230 VAC10ms/115 VAC, 230 VAC47 ~ 63Hz< / 277 VAC20 ~ 95% RH non-condensing-40 ~ +80 C, 10 ~ 95% RH 0 .03%/ C ( 0 ~ 60 C)10 ~ 500Hz, 5G , period for 72min. each along X, Y, Z axesENVIRONMENTPROTECTIONShut down output Voltage , re-power on to recoverShut down output Voltage , re-power on to recoverSHORT CIRCUIT TOTAL HARMONIC DISTORTIONDC VOLTAGERATED Current RATEDPOWER Voltage ADJ. RANGECURRENT ADJ. RANGELINE REGULATION LOAD REGULATION SETUP, RISE TIME UP TIME (Typ.)RIPPLE & NOISE (max.) TOLERANCE Current REGION Current Adjustable for A/AB-Type only (via the built-in potentiometer) Adjustable for A/AB-Type only (via the built-in potentiometer) COLD START 65A(twidth=550 s measured at 50% Ipeak) at 230 VAC ; P er NEMA 410 MAX.

3 No. of PSUs on 16A CIRCUIT BREAKER3 units (circuit breaker of type B) / 6 units (circuit breaker of type C) at 230 VACMAX. CASE TEMP. Tcase=+90 C(Please refer to "STATIC CHARACTERISTIC" section)100 ~ 305 VAC 142 ~ 431 VDC PF 0 .97/115 VAC, PF 0 .95/230 VAC, PF 0 .92/277 VAC@full load (Please refer to "POWER FACTOR (PF) CHARACTERISTIC" section)84~150W Constant Voltage + Constant Current LED Driver95 ~ 108%Hiccup mode, recovers automatically after fault condition is removedConstant Current limiting, recovers automatically after fault condition is ~ ~ 24V24V105W6 ~ 12 VELG-150-12150mVp-p5 ~ ~ ~ ~ ~ ~ ~ 48V48V105W 3 .0% 0 .5% 2 .0% ~ ~ ~ ~ ~ 3 .0% 0 .5% 1 .0% 2 .5% 0 .5% 1 .0% 2 .5% 0 .5% 0 .5% 2 .0% 0 .5% 0 .5% ~ ~ 54V54V105W49 ~ 2 .0% 0 .5% 0 .5%89%88%90%90%90%91% / 115 VAC / 230 VAC ~ 34V14 ~ 18V47 ~ 54V41 ~ 48V54 ~ 62V59 ~ 68 VTHD< 20%(@load 5 0%/115VC; @load 6 0%/230 VAC; @load 7 5%/277 VAC)(Please refer to TOTAL HARMONIC DISTORTION(THD) section)AUXILIARY DC OUTPUTN ominal 15V(deviation for BE-Type onlyNo load power consumption < for Blank / A / Dx / D2-TypeNO LOAD / STANDBYPOWER CONSUMPTIONS tandby power consumption < for B / AB / DA-TypeTcase=-40 ~ +90 C ( Please refer to OUTPUT LOAD vs TEMPERATURE section) ~ 305 VAC100 VAC ~ 180 VACRATED Current (for BE Type only) (For BE Type only) (Typ.))

4 (for BE Type only)87%86%88%88%88%89%(Except for BE Type) (For All the Types) EMC IMMUNITYMTBFDIMENSIONOTHERSNOTEPACKINGC ompliance to EN55015,EN61000-3-2 Class C (@load 6 0%) ; EN61000-3-3,EAC TP TC 020; K; GB17743, KN15,KN61547219*63* (L*W*H)EMC EMISSION SAFETY &EMCI/P-O/ I/P- O/P- , I/P-FG, O/P-FG:100M Ohms / 500 VDC / 25 C/ 70% RHWITHSTAND VOLTAGEISOLATION RESISTANCESAFETY STANDARDS Compliance to EN61000-4-2,3,4,5,6,8,11; EN61547, light industry level (surge immunity Line-Earth 6KV, Line-Line 4KV),EAC TP TC 020; KC KN15,KN61547 C C C C ; 16 hrs min. Telcordia SR-332 (Bellcore) min. MIL-HDBK-217F (25 C)DALI STANDARDS Compliance to IEC62386-101,102,(207 by request) for DA Type onlyUL8750(type HL )(except for BE-type), CSA No. ;IEC/EN/AS/NZS 61347-1,IEC/EN/AS/NZS 61347-2-13 independent,EN62384,,BIS I S15885(for 12/12B/12DA/24/24B/24DA/36A/42/42A/48A/5 4 only)EAC TP TC 004,; IP65 or IP67; KC61347-1,KC61347-2-13 , Name:ELG-150-SPEC 2020-04-08 LED Driver Constant Voltage + Constant Current 150W MEAN WELL ELG-150 SeriesTRC ELECTRONICS, INC.

5 ELECTRONICS, exceptional customer service since 1982 ELG-150 seriesBlock DiagramPFC fosc : 50~120 KHzPWM fosc : 60~130 KHz84~150W Constant Voltage + Constant Current LED Driver T his series is able to work in either Constant Current mode (a direct drive way) or Constant Voltage mode (usually through additional DC/DC Driver ) to drive the METHODS OF LED MODULET ypical output Current normalized by rated Current (%) In the Constant Current region, the highest Voltage at the output of the Driver depends on the configuration of the end systems. Should there be any compatibility issues, please contact MEAN (min.)Vo(%)50100Io(%)(B)ConstantCurrent a rea(C)HiccupProtection(A)ConstantVoltage a reaDETECTIONPWM & FILTERRECTIFIERSPOWERSWITCHINGFILTER&REC TIFIERSVo+Vo- This characteristic applies to Blank/A/B/AB/DX/D2/BE-Type, F or DA-Type, the Constant Current area is 60%~100% :Protective EarthFile Name:ELG-150-SPEC 2020-04-08 TRC Electronics for details.

6 LED Driver Constant Voltage + Constant Current 150W MEAN WELL ELG-150 SeriesTRC ELECTRONICS, INC. ELECTRONICS, exceptional customer service since 1982AC/L(Brown)AC/N(Blue)DIMMING OPERATIONELG-150 Applying additive 0 ~ 10 VDC Applying additive 10V PWM signal (frequency range 100Hz ~ 3 KHz): Applying additive resistance:Note : 1. Min. dimming level is about 8% and the output Current is not defined when 0%< Iout<8%. 2. The output Current could drop down to 0% when dimming input is about 0k o r 0 Vdc, or 10V PWM signal with 0% duty +Vo-DIM+DIM-+++--- D O NOT connect "DIM- to Vo-"Additive VoltageVo+Vo-DIM+DIM-++-- D O NOT connect "DIM- to Vo-"Additive PWM signalVo+Vo-DIM+DIM-++-- D O NOT connect "DIM- to Vo-"Additive Resistance0V 1V 2V 3V 4V 5V 6V 7V 8V 9V 10V10%0%20%30%40%50%60%70%80%90%100%Outp ut Current (%)0%10% 20% 30% 40% 50% 60% 70% 80% 90% 100%10%0%20%30%40%50%60%70%80%90%100%Out put Current (%)10%0%20%30%40%50%60%70%80%90%100%Outp ut Current (%)Dimming input.

7 Additive voltageDuty cycle of additive 10V PWM signal dimming inputELG-150 series84~150W Constant Voltage + Constant Current LED Driver 3 i n 1 dimming function (for B/AB-Type) O utput Constant Current level can be adjusted by applying one of the three methodologies between DIM+ and DIM-: 0 ~ 10 VDC, or 10V PWM signal or resistance. D irect connecting to LEDs is suggested. It is not suitable to be used with additional drivers . D imming source Current from power supply: 100 A (typ.) * DIM+ for B/AB-Type DA+ for DA-Type PROG+ for D2-Type* *DIM- for B/AB-Type DA- for DA-Type PROG- for D2-TypeShort10K/N 20K/N 30K/N 40K/N 50K/N 60K/N 70K/N 80K/N 90K/N 100K/N(N= Driver quantity for s ynchronized d imming o peration)Dimming input: Additive resistanceDIM-(White)**DIM+( )*BlueVo+(Red)Vo-(Black)File Name:ELG-150-SPEC 2020-04-08 LED Driver Constant Voltage + Constant Current 150W MEAN WELL ELG-150 SeriesTRC ELECTRONICS, INC.

8 ELECTRONICS, exceptional customer service since 1982 D ALI I nterface (primary side; for DA-Type) A pply DALI signal between DA+ and DA-. D ALI p rotocol comprises 16 groups and 64 addresses. F irst step is fixed at 8% of output. S mart timer dimming function (for Dxx-Type by User definition) MEAN WELL Smart timer dimming primarily provides the adaptive proportion dimming profile for the output Constant Current level to perform up to 14 consecutive hours. 3 dimming profiles hereunder are defined accounting for the most frequently seen applications. If other options may be needed, please contact MEAN WELL for details. Ex : D01-Type: the profile recommended for residential lighting Ex: D02-Type: the profile recommended for street lighting**: TIME matches Operating Time in the diagram whereas LEVEL matches Dimming Level.

9 Example: If a residential lighting application adopts D01-Type, when turning on the power supply at 6:00pm, for instance:[1] The power supply will switch to the Constant Current level at 100% starting from 6:00pm. [2] The power supply will switch to the Constant Current level at 70% in turn, starting from 0:00am, which is 06:00 after the power supply turns on. [3] The power supply will switch to the Constant Current level at 50% in turn, starting from 1:00am, which is 07:00 after the power supply turns on.[4] The power supply will switch to the Constant Current level at 70% in turn, starting from 5:00am, which is 11:00 after the power supply turns on. The Constant Current level remains till 8:00am, which is 14:00 after the power supply turns on.**: TIME matches Operating Time in the diagram whereas LEVEL matches Dimming : If a street lighting application adopts D02-Type, when turning on the power supply at 5:00pm, for instance:[1] The power supply will switch to the Constant Current level at 50% starting from 5:00pm.

10 [2] The power supply will switch to the Constant Current level at 80% in turn, starting from 6:00pm, which is 01:00 after the power supply turns on. [3] The power supply will switch to the Constant Current level at 100% in turn, starting from 8:00pm, which is 03:00 after the power supply turns on.[4] The power supply will switch to the Constant Current level at 60% in turn, starting from 1:00am, which is 08:00 after the power supply turns on.[5] The power supply will switch to the Constant Current level at 80% in turn, starting from 4:00am, which is 11:00 after the power supply turns on. The Constant Current level remains till 6:30am, which is 14:00 after the power supply turns up for D01-Type in Smart timer dimming software program: Set up for D02-Type in Smart timer dimming software program:TIME**TIME**06:0001:00T1T1T2T2T3 T3T4T4T507:0003:0011:008:0011:00------LE VEL**LEVEL**100%70%80%50%50%100%70%60%80 %Dimming Level(%)Operating Time(HH:MM)Dimming Level(%)Operating Time(HH:MM)ELG-150 series84~150W Constant Voltage + Constant Current LED DriverFile Name:ELG-150-SPEC 2020-04-08 LED Driver Constant Voltage + Constant Current 150W MEAN WELL ELG-150 SeriesTRC ELECTRONICS, INC.