Linear Bushing Series - THK

Mounting Procedure and Maintenance LM Guide - …

Mounting Procedure <Example of Mounting the LM Guide When an Impact Load is Applied to the Machine and therefore Rigidity and High Accuracy are Required >

  Guide, Maintenance, Procedures, Mounting, Mounting procedure and maintenance lm guide

THK Original Grease AFE-CA Grease

A THK Original Grease AFE-CA Grease Ô Base oil: high-grade synthetic oil Ô Consistency enhancer: urea-based AFE-CA Grease uses urea as a consistency enhancer and a high-grade synthetic oil as the base oil.

  Original, Grease, Thk original grease afe ca grease

Models SHS-C and SHS-LC - THK Technical Support

Model number coding A 5P EPXOMPBE B EFTJSFE EBUB TFBSDI GPS UIF DPSSFTQPOEJOH NPEFM OVNCFS JO UIF 5FDIOJDBM TJUF IUUQT UFDI UIL DPN Models SHS-C and SHS-LC (φH through)

  Model, Models shs c and shs

Models SHS-V and SHS-LV - THK

Model number coding A 5P EPXOMPBE B EFTJSFE EBUB TFBSDI GPS UIF DPSSFTQPOEJOH NPEFM OVNCFS JO UIF 5FDIOJDBM TJUF IUUQT UFDI UIL DPN Models SHS-V and SHS-LV B ¢K £ H3 M T 4-S ·ℓ W2 W W1 Model No. Outer dimensions LM block dimensions Pilot hole for side nipple Î Î Height Width Length

  Model, Models shs v and shs

Caged Ball LM Guide Global Standard Size Model SHS

A Types and Features Model SHS-C Speci Þ cation TableðA The ß ange of the LM block has tapped holes. Can be mounted from the top or the bottom. Used in places where the table cannot have

  Standards, Spices, Action

Features of the Ball Screw - THK Technical Support

Features of the Ball Screw Driving Torque One Third of the Sliding Screw With the Ball Screw, balls roll between the screw shaft and the nut to achieve high ef Þ ciency.

  Screw, Ball, Ball screws, Ball screw thk

Permissible Axial Load - THK

A Permissible Axial Load <Buckling Load on the Screw Shaft > With the Ball Screw, it is necessary to select a screw shaft so that it will not buckle when the maxi-

  Load, Axial, Permissible, Permissible axial load

Compliant with New Accuracy Standards Caged Ball LM …

2 Global Standard Type Caged Ball LM Guide SHS LM block LM rail Endplate End seal Ball cage Ball Cross section 45。 45 。 Structure of Model SHS Balls roll in four rows of raceways precision-ground on an LM rail and an LM block, and ball cages and

  With, Standards, Complaints, Accuracy, Caged, Compliant with new accuracy standards caged

Smooth Silent Ecological - THK Technical Support

Special Environmental Specifications of Linear Motion Systems HSR HR HRW SR RSR SSR SHW SRS Clean Rooms HSR-M2 LM Guide with Caged Ball Technology Caged Roller LM Guide

  Smooth, Silent, Ecological, Caged, Smooth silent ecological

Model DCM - THK

A Lead Screw Nut D 1 PCD D Dr D o D k 4- B r 1- d H F L Unit: mm Screw shaft Screw shaft details Standard shaft length Maximum length Dynamic permis-sible thrust Static

  Model

Product Ordering Guide - THK

LM Guides to be used in all orientations. Radial model SSR Page 1 SR Page 5 Machining center NC lathe Drilling machine Electric discharge machine Conveyance system • Capable of receiving a large moment due to a 4-way equal-load, wide, low gravity center structure. • The geometrical moments of inertia of the LM rail is large and the lateral ...

CHAPTER 7 PROJECT COST ESTIMATE - JICA

SPL 620 Concrete Barrier (New Jersey Type ) lm 4,660.55 SPL Installation of Fiber Optic lm 6,881.28 SPL Noise Barrier lm 48,031.19 SPL 1110 Toll Road Linghting each 158,671.93 4.0 TOLL PLAZA AND SERVICE AREA SPL 801 Truck Weigning Station set 3,564,478.23 SPL 1041(3)aToll Island, each 244,743.42138,225.73

CHAPTER 7 PROJECT COST ESTIMATE - JICA

SPL 414 Metal Decking (8 mm thk) 134,262.00 sq.m. 2,428.25 SUB-TOTAL (PART F) G DRAINAGE AND SLOPE PROTECTION STRUCTURES ... SPL Installation of Fiber Optic 18,217.00 lm 6,881.28 SPL 1110 Toll Road Linghting 150.00 each 158,671.93 SPL200 Relocation of High-tension Electric Cable and Tower 1.00 PS 50,000,000.00 ...

LMガイドの潤滑方法 - tech.thk.com

lmガイドの機能を十分に発揮させるには、使用条件に応じて最適な潤滑剤を 選ぶことがとても重要です。 今、使っているLMガイドは適切な潤滑状況が保たれているでしょうか？ 今日は良好な潤滑方法について少しご紹介します。 LMガイドの潤滑方法

Models RSR-M, RSR-N and RSR-TN - THK

A1-261 LM Guide RSR Models RSR5WTM/WTN Models RSR7WTM/WTN 〃〃 W M B （K） H3 N W2 W1 M1 h L1 L F N （E） φd1 φd2 2-S×ℓ L1 L C F h W M M 1 B （K） H3 N W2 W1 φd1 φd2 4-S×ℓ Unit: mm LM rail dimensions Basic load rating Static permissible moment N-m ＊ Mass Width Height Pitch Length ＊ C C 0