MIC Mounting Brackets and Other Accessories

1 Video | MIC Mounting Brackets and Other Accessories MIC Mounting Brackets and Other Accessories u Full range of Mounting Brackets and Other Accessories . u Designed to integrate seamlessly with the MIC. family. u Provides a best-fit solution for virtually any application. u Easy to use and install. u Accessories extend functionality. Bosch Security Systems offers a range of Mounting System overview Brackets and accessory products for the MIC family of cameras. The Mounting Brackets (for corner, wall, and Mounting Accessories pole Mounting ) are available in the standard colors of Deep Conduit Adapter the MIC family. (Note: Not all colors of Mounting The MIC Deep Conduit Adapter (DCA) is designed to Brackets are available for all models of MIC cameras.)

2 Allow a weatherproof conduit or cable gland to be The Accessories have been designed to work fitted to protect the signal cables. The DCA provides a seamlessly with MIC cameras to extend their convenient Mounting point for a MIC IP camera. functionality for your application. This datasheet The hinge feature allows installers to hang the provides an overview of the available MIC Accessories . camera temporarily but securely during installation for The following Accessories have their own datasheets: easier connection of cables/wiring before final bolts MIC illuminators (for MIC IP camera models) are installed. MIC Alarm/Washer Interface (MIC-ALM-WAS-24) The DCA has two M25 holes, one in the base and one High PoE Midspan models in the side.

3 VG4-A-PSU series An O-ring seals the camera-to-mount interface to an VIDEOJET connect 7000 (VJC-7000-90) ingress rating of IP68. The Serial Protocol Software License (MVS-FCOM- Supplied hardware includes: PRCL), an e-license key for serial protocol for MIC IP Four (4) M8 x 20 stainless steel hex bolts cameras, is also available. Four (4) M8 stainless steel plain washers One (1) O-ring, 80 mm x 3 mm One (1) end cap/blanking plug, M25 x , with O-ring Certain models (MIC-DCA-HxA) also include: One (1) conduit adapter (male M25 to female 3/4". NPT). 2 | MIC Mounting Brackets and Other Accessories Supplied hardware includes: Wall Mount Bracket Four (4) M8 x 30 stainless steel cap head bolts The MIC Wall Mount Bracket (MIC-WMB) allows Six (6) M6 x 20 stainless steel countersunk head Mounting on building walls.

4 It also coordinates with a bolts MIC Pole Mount Bracket (MIC-PMB) and a MIC Two (2) high-torque stainless steel worm drive clips Shallow Conduit Adapter (MIC-SCA) to allow Mounting (banding straps), 1 m long a MIC camera on a lamp post, scaffolding, or Other Two (2) pole mount blocks non-standard Mounting post. The MIC-WMB has a One (1) Mounting plate deep bowl to accommodate the signal cable Corner Mount Bracket connections. The MIC Corner Mount Bracket (MIC-CMB). An O-ring seals the camera-to-mount interface to an coordinates with a MIC-SCA and a MIC-WMB to allow ingress rating of IP68. Mounting a MIC camera on the corner of a building.

5 120 mm ( in.). Supplied hardware includes: Four (4) M8 x 20 stainless steel hex bolts 564 mm ( in.). Four (4) M8 stainless steel plain washers One (1) O-ring, 80 mm x 3 mm Supplied hardware includes: Four (4) M8 x 25 stainless steel hex bolts Pole Mount Bracket Four (4) M8 stainless steel plain washers The MIC Pole Mount Bracket (MIC-PMB) coordinates Four (4) M8 stainless steel nuts with a MIC-SCA and a MIC-WMB to allow Mounting a Spreader Plate MIC camera on a lamp post, scaffolding, or Other non- The MIC Spreader Plate (MIC-SPR) is used to spread standard Mounting post. The MIC-PMB accommodates the weight of a MIC camera and its supporting a wide range of diameters.

6 Brackets so that the camera can be mounted securely to a flat masonry surface. 3 | MIC Mounting Brackets and Other Accessories 9 mm ( in.). mm ( in.). 190 mm square ( in.). Supplied hardware includes: Four (4) M8 x 30 stainless steel cap head bolts Four (4) M8 stainless steel plain washers Four (4) M8 stainless steel nuts Sunshield Kits Shallow Conduit Adapter Sunshield Kits are available for various MIC cameras. The MIC Shallow Conduit Adapter (MIC-SCA) is used Each kit is designed to provide additional protection as required with Other Mounting Brackets . The MIC- for the camera from direct solar radiation, particularly SCA has a single M25 side entry conduit fitting hole.

7 In sunny climates, by reflecting solar exposure, and by There is not sufficient room inside to allow the camera creating an insulating gap between the environment to be mounted to it directly. (Use a MIC-DCA-Hx or a and the surface of the camera. MIC-DCA instead.). An O-ring seals the camera-to-mount interface to an Sunshield Kit for MIC IP fusion 9000i cameras The Sunshield Kit for MIC IP fusion 9000i cameras ingress rating of IP68. (MIC-9K-SNSHLD-W) includes two (2) white, molded shells that attach to the tilt head of the camera. Supplied hardware includes: Four (4) M4 x 8 stainless steel socket head Torx screws Four (4) M4 stainless steel flat washers Supplied hardware includes: Four (4) M8 x 20 stainless steel hex bolts Sunshield for MIC IP ultra 7100i and MIC IP.

8 Starlight 7100i Four (4) M8 stainless steel plain washers The one-piece sunshield (MIC-7100I-SNSHLD-W). One (1) O-ring, 80 mm x 3 mm attaches to the head of MIC IP ultra 7100i and MIC IP. One (1) end cap/blanking plug, M25 x , with O-ring starlight 7100i cameras. Other Hardware Accessories The sunshield has a section that installers can cut out, M25 to 3/4"NPT Thread Adapter (MIC- before installation, to make space to install a MIC. M25 XNPT34) illuminator. The conduit adapter (male M25 to female 3/4" NPT). (MIC-M25 XNPT34) allows attachment of NPT. conduit that is popular in the North American region to MIC-DCA-Hx, MIC-DCA, and MIC-SCA mounts that have threaded holes.

9 This adapter is included with the following DCA models: MIC-DCA-HBA, MIC-DCA- HWA, and MIC-DCA-HGA. The adapter is manufactured from 316 stainless steel and includes a silicone O-ring that seals the adapter to the conduit adapter to an Supplied hardware includes: ingress rating of IP68. Two (2) M4 x 8 Torx screws, of stainless steel, with socket heads 4 | MIC Mounting Brackets and Other Accessories Washer Kit Typical Mounting Arrangement, Corner mount The MIC washer kit (MIC-WKT-IR) connects a washer pump and water reservoir tank to a MIC camera. MIC-CMB-BD, Supplied hardware includes: -WD, -MG. One (1) washer jet nozzle Two (2) Mounting Brackets for the washer jet nozzle Certifications and approvals Region Regulatory compliance/quality marks MIC-SCA-BD, Europe CE - MIC-9K-IP67-5PK -WD, -MG.

10 MIC-WMB-BD, -WD, -MG. Installation/configuration notes Typical Corner mount configuration Typical Mounting Arrangement, Wall mount Not shown: Mounting hardware. Typical Mounting Arrangement, hinged DCA. MIC-SPR-BD, -WD, -MG. MIC-SCA-BD, -WD, -MG. MIC-WMB-BD, MIC-7130, -WD, -MG MIC-7230. Typical Wall mount configuration Not shown: Mounting hardware. Typical Mounting Arrangement, Pole mount MIC-WMB-BD, -WD, -MG. MIC-SCA-BD, -WD, -MG. MIC-DCA-HB, -HW, -HG. MIC-PMB. Typical hinged DCA mount configuration Technical specifications Typical Pole mount configuration MIC Hinged DCA. Not shown: Mounting hardware. Dimensions 120 x mm (H x W) ( x in.)