Transcription of MODEL T10167 MINI QUICK CHANGE TOOL POST SET
1 MODEL T10167 mini QUICK CHANGE tool POST SETINSTRUCTIONSC opyright MAy, 2010 By grizzly industriAl, : NO PORTION Of THIS MANUAL MAy bE REPRODUCED IN ANy SHAPE O R fORM WITHOUT THE WRITTEN APPROvAL Of GRI zzLy INDUSTRIAL, INC. # ts12954 printed in indiAUnderstand and follow the safety instruc-tions in the owner's manual for your prevent injury from tools coming loose, always firmly secure the tools in the holders and extend it from the holder no more than 2 1 2 times its cross section, and make sure that all cap screws and the tool post nut are fully tightened before starting the lathe. Check for safe clearances from the chuck, workpiece, and other lathe parts before starting the swing ..7 " 11"Maximum tool post size .. 10mm (Aprox. 3 8")Maximum tool Bit size ..1 2" tool post Body size.
2 " square x " highBoring tool /drill Chuck shank Max. size ..1 2"Inventorythe following is a description of the components shipped with the MODEL T10167 . lay the compo-nents out to inventory them. Description (figure 1) QtyA. tool post Body .. 1b. square/round tool holder 1 2" .. 1C. square tool holder 1 2" .. 1D. Knurling tool .. 1E. Medium Knurling Wheels .. 2f. Coarse Knurling Wheels .. 2G. Fine Knurling Wheels .. 2H. hss parting tool 3 32" x 1 2" x 3 1 2" .. 1I. 3 8" drill Chuck w/ 1 2" shank .. 1J. Chuck Key .. 1K. hex Wrenches 4, 6mm .. 1 eachL. Boring tool /drill Chuck holder 1 2" .. 1M. parting tool holder 1 2" .. 1 tool Post bodythe tool post body has a 10mm (approximately 3 8") mounting hole for the tool post. one side of the hole is countersunk for tool posts with extend-ed the existing tool post nut and holder , slide the T10167 tool post body over the tool post, then firmly secure it with the post you need help with your new QUICK CHANGE tool post, call our Tech Support at: (570) 1.
3 MODEL T10167 CM-2- T10167 mini QUICK CHANGE tool post set1234567891011121314151617181920316321 tool HoldersClean the mating dovetail surfaces of the tool holder and post body, then slide the holder into the dovetail. After mounting the tool , it can be aligned with the spindle center line by adjusting the cap screw and knurled knob on top of the holder . loosen the cap screw, adjust the knurled knob to bring the tool in alignment, then, while holding the knurled knob in place, re-tighten the cap parts of the MODEL T10167 are case hardened and coated with a black oxide finish for long life. on a regular basis and when changing a holder , use a stiff brush and mineral spirits to clean away any chips and grime. take extra care with the drill chuck assembly to ensure that chips do not inter-fere with its PART #DESCRIPTIONREF PART #DESCRIPTION1PT10167001 tool POST BODY12 PAW04 MHEX WRENCH 4MM2 PCAP31 MCAP SCREW X 2513 PAW06 MHEX WRENCH 6MM3 PCAP24 MCAP SCREW X 1614PT10167014 SQUARE tool holder 1/2"4PT10167004 KNURLED KNOB SQUARE/ROUND tool holder 1/2"5PT10167005 KNURLING tool HOLDER16 PCAP20 MCAP SCREW X 146PT10167006 KNURLING WHEEL PIN17PT10167017 PARTING tool holder 1/2"7PT10167007 MEDIUM KNURLING WHEEL18PT10167018 PARTING tool PLATE8PT10167008 COARSE KNURLING WHEEL19PT10167019 BORING tool holder 1/2"9PT10167009 FINE KNURLING WHEEL20 PSS24 MSET SCREW X 2510PT10167010 PARTING tool HSS 3/32" X 1/2" X 3-1/2"21PT10167021 CHUCK KEY11PT10167011 DRILL CHUCK 3/8" W/1/2" SHANK ASSY
