94540 Rocker Tool Post - Harbor Freight Tools

1 Rocker tool PostASSEMBLY AND OPERATING INSTRUCTIONS3491 Mission Oaks Blvd., Camarillo, CA 93011 Visit our Web site at 2006 by Harbor Freight Tools . All rights reserved. No portion of thismanual or any artwork contained herein may be reproduced in any shape or formwithout the express written consent of Harbor Freight technical questions and replacement parts, please call 1-800-444-335394540 Machine tool shown in photo not included. Due to continuing improvements, actual product may differ slightly from the product described 94540 For technical questions please call 1-800-444-3353 Page 2 SpecificationsSave This ManualYou will need the manual for the safety warnings and precautions, assembly instructions,operating and maintenance procedures, parts list and diagram.

2 Keep your invoicewith this manual. Write the invoice number on the inside of the front cover. Keep themanual and invoice in a safe and dry place for future Warnings and PrecautionsWARNING: When using tool , basic safety precautions should always be followedto reduce the risk of personal injury and damage to all instructions before using this tool ! work area clean. Cluttered areas invite work area conditions. Do not use machines or power Tools indamp or wet locations. Don t expose to rain. Keep work area well lit. Do notuse electrically powered Tools in the presence of flammable gases or children away.

3 Children must never be allowed in the work area. Donot let them handle machines, Tools , or extension idle equipment. When not in use, Tools must be stored in a drylocation to inhibit rust. Always lock up Tools and keep out of reach the right tool for the job. Do not attempt to force a small tool orattachment to do the work of a larger industrial tool . There are certainapplications for which this tool was designed. It will do the job better and moresafely at the rate for which it was intended. Do not modify this tool and do notuse this tool for a purpose for which it was not intended.

4 :noitcurtsnoCleetSdenihcaM:eziSredloHloo T" -1x" mumixaMknahs:kcolBgnitnuoMH"8/3xW"2xL"8/ 7-1:lenaPrekcoRH"8/3xW" xL" -2:retemaiDesaBH"8/1-1xretemaid" -2:retemaiDedisnIesaB"8/3-1gnitnuoMlartn eC:dutSdaeHerauqS"61/7gnikcoLtsoPlartneC :eziSpirtS"61/3tsoPlartneC:snoisnemiDret emaid"8/3-1xL"8/1-3:tolSlartneCtsoPL"8/7 -1xW"61/31 "61/11-1:dutSgnikcoLtsoPretemaid"61/5xL" 61/3:eziSehtaLmumixaM"31 94540 For technical questions please call 1-800-444-3353 Page properly. Do not wear loose clothing or jewelry as they can be caughtin moving parts. Protective, electrically non-conductive clothes and non-skidfootwear are recommended when working.

5 Wear restrictive hair covering tocontain long eye and ear protection. Always wear ANSI approved impact safetygoggles. Wear a full face shield if you are producing metal filings or woodchips. Wear an ANSI approved dust mask or respirator when working aroundmetal, wood, and chemical dusts and not overreach. Keep proper footing and balance at all times. Do notreach over or across running Tools with care. Keep Tools maintained and clean for better andsafer performance. Follow instructions for lubricating and changingaccessories. The handles must be kept clean, dry, and free from oil andgrease at all adjusting keys and wrenches.

6 Check that keys and adjustingwrenches are removed from the tool or machine work surface before plugging it alert. Watch what you are doing, use common sense. Do not operateany tool when you are for damaged parts. Before using any tool , any part that appearsdamaged should be carefully checked to determine that it will operateproperly and perform its intended function. Check for alignment and bindingof moving parts; any broken parts or mounting fixtures; and any othercondition that may affect proper operation. Any part that is damaged shouldbe properly repaired or replaced by a qualified technician.

7 Do not use the toolif any switch does not turn On and Off against electric shock. Prevent body contact with grounded surfacessuch as pipes, radiators, ranges, and refrigerator parts and accessories. When servicing, use only identicalreplacement parts. Use of any other parts will void the warranty. Only useaccessories intended for use with this tool . Approved accessories areavailable from Harbor Freight not operate tool if under the influence of alcohol or drugs. Readwarning labels on prescriptions to determine if your judgment or reflexes areimpaired while taking drugs. If there is any doubt, do not operate the For your safety, service and maintenance should be performedregularly by a qualified 94540 For technical questions please call 1-800-444-3353 Page 4 Warning: The warnings, cautions, and instructions discussed in this instructionmanual cannot cover all possible conditions and situations that may occur.

8 Itmust be understood by the operator that common sense and caution are factorswhich cannot be built into this product, but must be supplied by the unpacking, check to make sure that the product is intact and any parts are missing or broken, please call Harbor Freight Tools at the numberon the cover of this tool posts are useful for increased rake angle of the cutting tool . They arealso helpful when machining in a tight or hard to reach Rocker tool post fits into a standard top slide tool post holder whichaccepts a maximum shank size of x 1- . the Rocker tool post into position on your tool post holder (notincluded).

9 Your selected tool (not included) in the Rocker tool post , adjust itsposition, and tighten in place. Position the tool post assembly and your workmaterial in your machine tool according to safe machining with your machining completed, remove the tool from the Rocker tool post . Remove theRocker tool post from the tool post use, brush all metal chips and debris from the Rocker tool cleaning, apply a light coating of machine oil to prevent the Rocker tool post holder in a safe and secure 94540 For technical questions please call 1-800-444-3353 Page 5 NOTE: Some parts are listed and shown for illustration purposes only and are notavailable individually as replacement READ THE FOLLOWING CAREFULLYTHE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAMIN THIS MANUAL AS A REFERENCE tool ONLY.

10 NEITHER THE MANUFACTURER NORDISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THEBUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT ORTHAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT,THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRSAND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED ANDLICENSED TECHNICIANS AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISKAND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCTOR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATIONOF REPLACEMENT PARTS List(4) Shank(3) Base(2) RockerMachine tool (not included)(1) Central Mounting Stud#traPnoitpircseD1dutSgnitnuoMlartneC 2rekcoR3esaB4knahSSKU 94540 For technical questions please call 1-800-444-3353 Page 6 Harbor Freight Tools Co.