MODELS: TG8S / TGLS FEATURES - UPGNET

1 363658-CTG-H-0616. DESCRIPTION. These compact units employ induced combustion, reliable hot surface ignition and high heat transfer aluminized tubular heat exchangers. The units are factory shipped for installation in upflow or horizontal applications and may be converted for downflow applications. These furnaces are designed for residential installation in a TECHNICAL GUIDE basement, closet, alcove, attic, recreation room or garage and are also ideal for commercial applications. All units are factory GAS-FIRED RESIDENTIAL assembled, wired and tested to assure safe dependable and SINGLE STAGE MULTI-POSITION economical installation and operation.

2 GAS FURNACES These units are Category I listed and may be common vented STANDARD &Low NOx MODELS with another gas appliance as allowed by the National Fuel Gas Code. MODELS: TG8S / TGLS. FEATURES . NATURAL GAS Easily applied in upflow, horizontal left or right, or downflow 40 - 130 MBH INPUT installation with minimal conversion necessary. Compact, easy to install, ideal height 33" tall cabinet. Blower-off delay for cooling SEER improvement. Easy access to controls to connect power/control wiring. Built-in, high level self diagnostics with fault code displays standard on integrated control module for reliable operation. Low unit amp requirement for easy replacement application.

3 Single wire twinning or staging feature available. All models are convertible to use propane (LP) gas. Electronic Hot Surface Ignition saves fuel cost with increased dependability and reliability. 100% shut off main gas valve for extra safety. 4 speed, direct drive PSC motor. 24V, 40 VA control transformer and blower relay supplied for add-on cooling. Hi-tech tubular aluminized steel primary heat exchanger. Timed on, adjustable off blower capability for maximum com- fort. Blower door safety switch. Low NOx models have been designed to meet specific code requirements. Airflow leakage less than 1% of total airflow at duct perfor- mance testing conditions.

4 No knockouts to deal with, making installation easier. Movable duct connector flanges for application flexibility. Quiet inducer operation. Due to continuous product improvement, specifications Inducer rotates for easy conversion of venting options. are subject to change without notice. Fully supported blower assembly for easy access and Visit us on the web at removal of blower. Additional rating information can be found at External air filters used for maximum flexibility in meeting customers IAQ needs. Venting applications - may be installed as a common vent WARRANTY with other gas-fired appliances or use a masonry chimney.

5 20-year limited warranty on the heat exchanger. 1/4 turn knobs provided for easy door removal. 10-year heat exchanger warranty on commercial applications. Standard 5-year limited Parts warranty. Extended 10-year limited parts warranty when product is registered online within 90 days of purchase for replace- ment or closing for new home construction. FOR DISTRIBUTION USE ONLY - NOT TO BE USED AT POINT OF RETAIL SALE. 363658-CTG-H-0616. LEFT SIDE Vent Connection FRONT RIGHT SIDE. Electrical Outlet Entry Vent Electrical Connection Entry Outlet Gas Pipe Gas Pipe Entry Entry 33 . 23 . Thermostat Thermostat Wiring Wiring 14 . A 1.

6 4 Diameter .5 Vent Connection .5 . Outlet .5 . B B. C..5 20 . SUPPLY END RETURN END. Cabinet and Duct Dimensions Approximate Nominal Cabinet Cabinet Dimensions (Inches). Models Operating Weights CFM (m3/min) Size A B C Lbs TG(8,L)S040A08MP11 800 A 14 1/2 13 3/8 89. TG(8,L)S060A10MP11 1000 A 14 1/2 13 3/8 91. TG(8,L)S060A12MP11 1200 A 14 1/2 13 3/8 94. TG(8,L)S080B12MP11 1200 B 17 1/2 16 3/8 103. TG(8,L)S080C16MP11 1600 C 21 19 7/8 114. TG(8,L)S080C22MP11 2200 C 21 19 7/8 119. TG(8,L)S100B12MP11 1200 B 17 1/2 16 3/8 108. TG(8,L)S100C16MP11 1600 C 21 19 7/8 118. TG(8,L)S100C20MP11 2000 C 21 19 7/8 122. TG(8,L)S120C16MP11 1600 C 21 19 7/8 123.

7 TG(8,L)S120C20MP11 2000 C 21 19 7/8 129. TG(8,L)S130D20MP11 2000 D 24 1/2 23 3/8 135. Ratings & Physical / Electrical Data Air Temp. Max. Outlet Max Min. wire Size Input Output Blower Blower Total Unit Models AFUE Rise Air Temp Over-Current (awg) @ 75 ft Size Amps MBH MBH F F HP Amps Protect one way TG(8,L)S040A08MP11 40 32 25-55 190 1/5 9x8 10 14. TG(8,L)S060A10MP11 60 48 25-55 190 1/3 9x8 10 14. TG(8,L)S060A12MP11 60 48 30-60 190 1/3 11 x 8 10 14. TG(8,L)S080B12MP11 80 64 35-65 190 1/3 11 x 8 10 14. TG(8,L)S080C16MP11 80 64 25-55 190 1/2 11 x 10 15 14. TG(8,L)S080C22MP11 80 64 25-55 190 1 11 x 11 20 12. TG(8,L)S100B12MP11 100 80 40-70 190 1/3 9x8 10 14.

8 TG(8,L)S100C16MP11 100 80 35-65 190 1/2 11 x 10 15 14. TG(8,L)S100C20MP11 100 80 25-55 190 1 11 x 11 20 12. TG(8,L)S120C16MP11 120 96 40-70 190 1/2 11 x 10 15 14. TG(8,L)S120C20MP11 120 96 30-60 190 1 11 x 11 20 12. TG(8,L)S130D20MP11 130 104 35-65 190 1 11 x 11 20 12. Nominal external static pressure is at furnace outlet ahead of cooling coils. Annual Fuel Utilization Efficiency (AFUE) numbers are determined in accordance with DOE Test procedures. Wire size and over current protection must comply with the National Electrical Code (NFPA-70-latest edition) and all local codes. 2 Johnson Controls Unitary Products 363658-CTG-H-0616.

9 HORIZONTAL sidewall VENTING Recommended Filter Sizes For applications where vertical venting is not possible, the only Cabinet Side Bottom approved method of horizontal venting is the use of an auxiliary CFM. Size (in) (in). power vent. Auxiliary power venters must be approved by CSA, 800 A 16 x 25 14 x 25. UL, or other recognized safety agencies. Follow all application and installation details provided by the manufacturer of the 1000 A 16 x 25 14 x 25. power vent. 1200 A 16 x 25 14 x 25. 1200 B 16 x 25 16 x 25. FILTER PERFORMANCE. 1600 B 16 x 25 16 x 25. The airflow capacity data published in the Blower Perfor- 1600 C 16 x 25 20 x 25.

10 Mance tables shown represents blower performance WITH- 2000 C (2) 16 x 25 20 x 25. OUT filters. 2200 C (2) 16 x 25 20 x 25. All applications of these furnaces require the use of field 2000 D (2) 16 x 25 22 x 25. installed air filters. All filter media and mounting hardware or provisions must be field installed external to the furnace cabi- 1. Air velocity through throwaway type filters may not exceed 300 feet per min- ute ( m/min). All velocities over this require the use of high velocity fil- net. DO NOT attempt to install any filters inside the furnace. ters. 2. Do not exceed 1800 CFM using a single side return and a 16x25 filter.