Nitoprime 25 constructive solutions - Noble Corp

1 Nitoprime 25constructive solutionsNitoprime 25 UsesNitoprime 25 is suitable for priming concrete surfaces priorto the application of any of the Nitoflor SL2000/4000, TS / TFrange of resin based floor toppings, Nitocote range ofprotective coatings or Nitomortar range of epoxy Can be applied even on damp surfaces Improves the adhesion of epoxy floor toppings and mortarswith the 25 is a two component epoxy based primer withgood penetrating properties for concrete supportFosroc provides a countrywide technical advisory servicesupported by a team of specialists in the life90 mins30 minsApplication instructionsSurface preparationThorough surface preparation is vital.

2 For best results Fosrocrecommends mechanical preparation techniques. (Forexample, mechanical scarifying, grit-blasting, sand blasting).For flooring and tanking works, care must be taken to ensurethat the substrate does not suffer from rising dampness. Ifsuch conditions exist, consult concrete floorsShould be at least 28 days old or have a moisturecontent ofless than 5% before proceeding with epoxy and deposits on new concrete floors are bestremoved by light grit blasting, mechanical scabbling orgrinding. On smaller areas thorough etching usingReebaklens may be considered.

3 After etching the floor, itshould be thoroughly washed with clean water and thenallowed to concrete floorsAgain, mechanical cleaning methods are stronglyrecommended on old concrete floors, particularly where heavycontamination by oil and grease has occurred or existingcoatings are present. These may well have been absorbedseveral millimeters deep into the concrete. To ensure goodadhesion all contamination should be removed and thesurface thoroughly cleaned of all dust and loose debris. Athorough detergent wash is also recommended followed bythorough cleaning with clean water and mopping it off to a the entire contents of the hardener tin to the base andmix thoroughly for 3 mins.

4 Until homogeneous, using a slowspeed drill ( 400 - 500 rpm) fitted with a suitable mixing mixed the primer should be applied immediately in athin continuous film to the clean prepared surface. Work theprimer into the surface using a stiff brush or roller. Excessapplication and puddling should be avoided. On poroussurfaces Nitoprime 25 will be absorbed very quickly leavingcharacteristic light coloured dry patches. it is recommendedthat a second priming coat be applied to these dry not only helps to ensure good adhesion but also preventsair release from the porous substrate which may causebubbles in the final epoxy topping Nitoflor SL2000 / 4000 applications, leave the Nitoprime25 to dry overnight.

5 For Nitoflor TF, Nitomortar and Nitocote,allow the solvent in the Nitoprime 25 to evaporate and becometacky. the relevant datasheets may please be referred to, toensure limitationsRecommended application range is 100C - 400C. Fosrocshall be consulted where application or service is outside therange of 50C to and coverageNitoprime 25 is available in 1 and 4 litre coverage rate - m2/ltrEpoxy resin based primer for concrete surfacesNitoprime 25 INDIA/2004/0501/DImportant note :Fosroc products are guaranteed against defective materials and manufacture and are sold subjectto its standard terms and conditions of sale, copies of which may be obtained on request.

6 WhilstFosroc endeavours to ensure that any advice, recommendation specification or information it maygive is accurate and correct, it cannot, because it has no direct or continuous control over whereor how its products are applied, accept any liability either directly or indirectly arising from theuse of its products whether or not in accordance with any advice, specification, recommendationor information given by fax e-mail++91 80-22240018/120 ++91 80-22233474 Chemicals (India) Pvt.

7 Office111/3, Hafeeza Chamber II Floor,K H Road, PBNo. 2744, Bangalore Denotes the trademark of Fosroc International Limited Regional OfficesBangaloreMumbai Delhi KolkataShankar House, IV Floor208/209, PersepolisFirst floor,1/2 East Patel Nagar30/B Jodhpur Park1 & 18, RMV ExtensionSector 17, VashiOpp: Vivek Cinema, Main Patel RdGround FloorBangalore 560 080 Navi Mumbai 400 703 New Delhi 110 008 Kolkata 700 068Ph:080-2361 3161/2361 2004Ph:022-2789 6412/14Ph:011-25884903/4Ph: 033 2472 5482 Fax : 080-2361 7454 Fax: 022 - 2789 6413 Fax: 011- 25884422 Fax: 033-2472 9921email: : (079) 26762799 zAnkleshwar.

8 (02646) 220704/224687 z Bhubaneshwar : (0674) 2521176 z Chennai (044) 24899949/24853383zChandigarh : (0172) 2639360 z Cochin : (0484) 2356668 zCoimbatore : (0422) 2472966 zGoa : (0832) 2542465 zGuwahati (0361) 2548793zHyderabad : (040) 27662324/27662425 z Hubli (0836) 3402597 zIndore : (0731) 504339/5061477 z Jaipur : (0141) 2235349 z Lucknow :(0522)22239044z Nagercoil (04652) 2224849 z Mangalore: (0824) 22272234 z Visakhapatnam : (0891) 2564850 StorageNitoprime 25 has a shelf life of 12 months when stored inunopened containers under normal warehouse & Safety instructionsNitoprime 25 should not come into contact with skin andeyes or be swallowed.

9 Avoid prolonged inhalation of people are sensitive to epoxy resins, hardeners andsolvents. Gloves, goggles and barrier creams shouldtherefore be used while handling the product. Adequateventilation should be ensured and if working is enclosedareas, suitable breathing apparatus must be used. If theresin comes in contact with skin, it must be removed beforeit hardens with a resin removing cream, followed by washingwith soap and water - solvent should not be Sol should be washed from skin immediately withsoap and water. Should accidental eye contamination occurwith any of the above products, it should be washed well withplenty of water and medical advice should be sought.

10 Ifswallowed medical attention should be sought should not be tools and equipments should be cleaned with Nitoflor Solimmediately after use. Spillages should be absorbed withsand or sawdust and disposed off in accordance with Sol, Nitoprime 25 are flammable. Do not expose tonaked flames or other sources of ignition. Do not smokewhile handling the materials. Containers should be tightlysealed when not in use. In the event of fire, extinguish withCO2 or foam type cream, followed by washing with soap and water -solvent should not be Sol should be washed from skin immediately withsoap and water.