Nitofill EPLV constructive solutions - Noble Corp

1 Nitofill EPLV constructive solutionsNitofill EPLVLow viscous epoxy injection resin groutUsesNitofill EPLV is used for injecting into cracks, honeycombs andcavities in concrete structures. It can also be used for groutingbase plates with very narrow gaps ( <10mm).Advantages Low viscosity - can be injected into fine cavities and narrowgaps. High mechanical strength - performs even under heavyloads and stresses. Excellent adhesive strength - Good bonding with substrate Two part system - easy to mix and handle Non shrink - complete filling of voids and cracks Chemical resistant - can be used in EPLV is a two part system comprising of liquid base andhardener. It is designed for injecting into narrow gaps, cracksand voids ranging from to supportFosroc offers a comprehensive range of high performance, highquality concrete repair and construction products. In addition,Fosroc offers technical support service to specifiers, end- usersand contractors, as well as on-site technical assistance inlocations all over the following results are typical for the hardened grout at (kg/m3) 1100 Compressive strength (N/mm2) 1D 3D 7 DBS6319 Part 2 45 60 70 Tensile strength (N/mm2)BS6319 Part 7 (7 days) 18 Flexural strength (N/mm2)BS6319 Part 4 (7 days) 55 Pot life60 minutes @ 200C30 minutes @ 300 CChemical resistanceNitofill EPLV is resistant to oil, grease, fats, most chemicals,mild acids and alkalis, fresh and sea water.

2 Fosroc shall becontacted when exposure to solvent or concentrated chemicalsis epoxy products will develop a temperature rise on extent will be a function of the volume to surface ratio, theambient temperature as well as the mass and thermalconductivity of the surrounding materials. Fosroc shall becontacted for specific clausesPerformance specificationAll epoxy injection must be carried out with a two component lowviscous epoxy resin system. The epoxy resin shall have sufficientlylow viscosity ( 150-300 cps) to ensure easy injection into cracksand voids. The epoxy injection grout shall develop a compressivestrength exceeding 60N/mm2 @ 7days, tensile strengthexceeding 15N/mm2 and flexural strength exceeding 50 mixed epoxy shall have a pot life exceeding 30 minutes specificationAll epoxy injection must be carried out using Nitofill EPLV manufactured by Fosroc and used in accordance with themanufacturer's storage, handling and placement of the grout must be instrict accordance with the manufacturer's instructionsSurface preparationThe area to be injected shall be cleaned to remove all loosematerial, laitence.

3 Grease and other injection holesInjection holes of 8 - 10mm dia shall be drilled at fixed intervalsalong the crack length or in a grid pattern incase of grouting ofvoids in holes shall be cleaned to remove all dust and loose materialby blowing compressed NipplesSuitable injection nipples of GI/PVC shall be fixed in these holesusing an epoxy sealing putty . The cracks shall also be sealedwith this of resinThe two components of Nitofill EPLV injection grout shall beindividually stirred and then mixed and injected into the nipplesthrough a suitable injection pump exerting a a uniform shall be carried out till it flows from the adjacent nippleand then stopped. The same operation shall be carried out forthe next EPLVINDIA/2004/00444/AImportant note :Fosroc products are guaranteed against defective materials and manufacture and are sold subjectto its standard terms and conditions of sale, copies of which may be obtained on request.

4 WhilstFosroc endeavours to ensure that any advice, recommendation specification or information it maygive is accurate and correct, it cannot, because it has no direct or continuous control over whereor how its products are applied, accept any liability either directly or indirectly arising from theuse of its products whether or not in accordance with any advice, specification, recommendationor information given by fax e-mail++91 80-22240018/120 ++91 80-22233474 Chemicals (India) Pvt. Office111/3, Hafeeza Chamber II Floor,K H Road, PBNo. 2744, Bangalore Denotes the trademark of Fosroc International Limited Regional OfficesBangaloreMumbai Delhi KolkataShankar House, IV Floor208/209, PersepolisFirst floor,1/2 East Patel Nagar30/B Jodhpur Park1 & 18, RMV ExtensionSector 17, VashiOpp: Vivek Cinema, Main Patel RdGround FloorBangalore 560 080 Navi Mumbai 400 703 New Delhi 110 008 Kolkata 700 068Ph:080-2361 3161/2361 2004Ph:022-2789 6412/14Ph:011-25884903/4Ph: 033 2472 5482 Fax : 080-2361 7454 Fax: 022 - 2789 6413 Fax: 011- 25884422 Fax: 033-2472 9921email: : (079) 26762799 zAnkleshwar :(02646) 220704/224687 z Bhubaneshwar : (0674) 2521176 z Chennai (044) 24899949/24853383zChandigarh : (0172) 2639360 z Cochin : (0484) 2356668 zCoimbatore : (0422) 2472966 zGoa : (0832) 2542465 zGuwahati (0361) 2548793zHyderabad : (040) 27662324/27662425 z Hubli (0836) 3402597 zIndore : (0731) 504339/5061477 z Jaipur : (0141) 2235349 z Lucknow.

5 (0522)22239044z Nagercoil (04652) 2224849 z Mangalore: (0824) 22272234 z Visakhapatnam : (0891) 2564850 After all the holes are completed, the nipples are removed nextday and the holes shall be sealed with a high strength : For grouting under base plates with very narrow gaps,either injection grouting or normal grouting by pouring, can beresorted to. For details, Fosroc shall be tools and equipment should be cleaned immediately after use with Nitoflor Sol. Spillages should be absorbedwith sand or sawdust and disposed in accordance with EPLV : 1 litre packStorageShelf life12 months in unopened container under normal and Safety instructionsNitofill EPLV epoxy grout contains resins which may causesensitisation by skin contact. Contact with skin and eyes andinhalation of vapour shall be avoided. Use of suitable protectiveclothing, gloves and eye/face protection is creams provide additional skin protection.

6 Shouldaccidental skin contact occur, it shall be removed immediatelywith a resin removing cream, followed by soap and should not be used. Incase of contact with eyes,immediate rinsing with plenty of clean water is suggested andmedical attention shall be sought immediately - Vomitingshould not be Sol is flammable. In the event of fire, use of fireextinguishers like Carbon dioxide or foam is point : 330 CAdditional informationThe Fosroc range of associated products includes high strengthcementitious, epoxy grout, polyester resin based mortar forrapid presetting of steel shimsto level or for direct bedding of small base plates; ResinAnchoring systems for same day anchoring of bolts in drilledholes in concrete or rock. Also available a range of products foruse in construction; viz., admixtures, curing compounds, releaseagents, flooring systems and repair mortars.

7 Separatedatasheets are available on these products.