Example: dental hygienist
NON-CONTACT VOLTAGE TESTER (NCVT-1) OwNER’S …
Scenario 1 – Powering on the tester: The “power on” LED in the tip of the tester changes from a steady green to a blinking green and a series of beeping sounds is generated. The tester then turns off. The unit is now deactivated and is not operational; the batteries require replacement. To …
Tags:
Information
Domain:
Source:
Link to this page:
Documents from same domain
INSTRUCTION MANUAL Digital AC/DC Voltage & …
data.kleintools.comINSTRUCTION MANUAL ET250 600V FRANÇAIS pg. 17 ESPAÑOL pg. 9 Digital AC/DC Voltage & Continuity Tester • AUTOMATICALLY SELECTS MEASUREMENT MODE
Screwdrivers, Nut Drivers and Accessories - Klein Tools
data.kleintools.comScrewdrivers, Nut Drivers and Accessories Offering a variety of tip types, hex sizes, shaft lengths, and handle designs, Klein has the screwdrivers
CABLE STRIPPERS - data.kleintools.com
data.kleintools.com• wire stripper/crimpers • cable strippers • pliers • nut driver • folding jab saw • knives • hybrid multi-tool • pocket thermometer
INSTRUCTION MANUAL Digital Circuit Breaker Finder
data.kleintools.comThe Klein Tools ET310 is a digital circuit breaker finder used to locate the correct circuit breaker in a panel to which an electrical outlet or fixture is connected. The transmitter is connected to the electrical ... the frequency of the audible beeps will increase. When located, the audible beep will sound continuously, the circuit status ...
Manual-Ranging Digital Meter - Klein Tools
data.kleintools.comDC VOLTAGE (LESS THAN 600V) 1. Insert RED test lead into V˚ jack 5, and BLACK test lead into COM jack 4, and rotate function selector switch 2 to the highest V DC ( ) setting (600V). 2. Measure voltage and rotate the function selector switch to successively lower V DC ( ) settings to obtain higher resolution measurements.
Test & Measurement - Klein Tools
data.kleintools.comvoltage, resistance, continuity, frequency, capacitance, and tests diodes via test-leads, and temperature via a thermocouple probe. It features a super bright high visibility dual-line OLED display screen that optimizes viewability in dark or bright environments and when viewed at indirect angles Features CL110 CL210 CL310 CL330
FIG. 1 INSTRUCTIONS – Dual-range Non-Contact Voltage ...
data.kleintools.comINSTRUCCIONES – Probador de voltaje sin contacto de rango dual (Español: página 3) INSTRUCTIONS – Testeur de tension sans contact à double plage (Français : page 4) DURABILITY / DURABILIDAD / DURABILITÉ Drop Protection Protección ante caídas Protection contre les chutes 6.6 ft. (2 m) Safety Rating Clasificación de seguridad Cote de ...
Wrenches - Klein Tools
data.kleintools.com7-Piece Combination Wrench Set - Metric 68500 Cat. No. Set Contains Weight 68500 1.2 lbs. (0.54 kg) Cat. No. Size Length Box End Point 68507 7 mm 5-1/8" (130.2 mm) 12
Auto-Ranging Digital Multimeter True RMS Technology
data.kleintools.com5 ELECTRICAL SPECIFICATIONS OTHER MEASUREMENT APPLICATIONS Maximum Input: 100V RMS in Voltage setting, 600V DC or 600V AC RMS in all other settings • Diode Test: 1.5 mA max, open circuit voltage 3.0V DC • Continuity Check: Audible signal when resistance <50Ω, max test current 0.35mA
Auto-Ranging Digital Multimeter - Klein Tools
data.kleintools.comAudible Continuity Diode Capacitance Hz Frequency % Duty-cycle Double Insulated Class II °F/°C Temperature (Fahrenheit / Celsius) Ground Fuse (with rating below symbol) Warning or Caution To ensure safe operation and service of this meter, follow all warnings and instructions detailed in this manual. Risk of Electrical Shock
Related documents
DUAL RANGE NON-CONTACT VOLTAGE TESTER (NCVT-2) …
www.kleintools.comThe unit will beep 3 times and the power-on LED will switch from blue to green or green to blue. The tester will start in whichever mode it was last powered off in. Checking for the presence of AC voltage: Prior to use, test on known live circuit to verify tester functionality. Place tip of the tester near an AC voltage and refer
The Transistor Tester user manual
img.banggood.comThe Transistor Tester user manual Power： Transistor Tester can be powered from 6.8V – 12V DC. This can be achieve by a 9V layer-built battery. Two 3.7V Lithium-ion battery in series. Or AC adapter. When power on , the current is about 30mA at DC 9V. Control:
NS-468 Cable Manaual
ftaelectronics.comNS-468 Cable Tester Instruction Manual Revision 1.0 4-23-2008 Page -3- Testing RJ11 4 Conductor Phone Cables Phone cables are connected from Pin to Pin on the opposite end, 2-2, 3-3, and so forth. See diagram. NOTE: Pin 1 and Pin 6 are not connected. When testing RJ11 phone cables: Tester will test each pin sequentially.
Multi-function Tester (TC-V2.12k)
www.circuitspecialists.comShort press: Press the key and not less than 10 ms, release key within 1.5 seconds Long press: Press the key more than 1.5 seconds 2.2 Power on In the power off state, short press the multifunction key, the tester is turned on and automatically measured. Power on & measurement interface 2.3 Detect transistor
The Complete Guide to Electrical Insulation Testing
www.instrumart.comFigure 3–Typical scale on the Megger insulation tester. HoW To InTERPRET RESISTAnCE REAdInGS As previously mentioned, insulation resistance readings should be considered relative. They can be quite different for one motor or machine tested three days in a row, yet not mean bad insulation. What really matters is the trend
VIAVI Solutions Data Sheet VIAVI
www.viavisolutions.comSmartOTDR Handheld Fiber Tester ... Pulse widths 5 ns to 20 µs 5 ns to 20 µs 3 ns to 20 µs Event dead zone4 1.35 m 1.35 m 0.9 m Attenuation dead zone5 4 m 4 m 2.5 m Splitter attenuation dead zone Not available Not available 45 m after 15 dB splitter loss CW Light Source9
Manual-Ranging Digital Meter - Klein Tools
data.kleintools.com8 ENGLISH OPERATING INSTRUCTIONS DC CURRENT 200mA to 10A 1. For DC currents more than 200mA and less than 10A, insert RED test lead into 10A jack 3, and BLACK test lead into COM jack 4, and rotate function selector switch 2 to the 10A DC setting.
TESTING FOR VOLTAGE DROP
drivcat.com1. Connect the positive test lead of a Digital Volt/Ohm meter (DVOM) to the power source. Use of an analog meter is not recommended because damage to the meter could result from improper polarity. 2. Connect the negative test lead to the other end of the wire for the circuit being tested ( pointA). 3. Operate the circuit and observe the meter ...