Optocoupler, Phototransistor Output, AC Input, …

1 TCMT1600, TCMT4600, Semiconductors Rev. , 21-Jul-151 Document Number: 83512 For technical questions, contact: DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT , Phototransistor output , AC Input, Single / Quad Channel, Half Pitch Mini-Flat PackageDESCRIPTIONThe low profile miniflat package includes an optocoupler with ac input and transistor output . It is available in single channel (4 pin) TCMT1600 or quad channel (16 pin) Low profile package (half pitch) AC isolation test voltage 3750 VRMS Low coupling capacitance of typical pF Low temperature coefficient of CTR Wide ambient temperature range Material categorization: for definitions of compliance please see APPLICATIONS Programmable logic controllersAGENCY APPROVALS UL1577, file no.

2 E76222, double protection cUL component acceptance service no 5A, double protection DIN EN 60747-5-5 (VDA 0884-5) FIMKO: FI EN 60950-1:2006 BSI: BS EN 60065:2002; BS EN60950-1:2006 CQC GB 8898-2011, GB (suitable for installation altitude below 2000 m)Notes Available only on tape and reel.(1)Product is rotated 180 in tape and reel PIN16 PIN1289 ORDERING INFORMATIONTCMT#60#PART NUMBERAGENCY CERTIFIED/PACKAGECTR (%)SINGLE CHANNELQUAD CHANNELUL, cUL, FIMKO, BSI, VDE80 to 30080 to 300100 to 300 SOP-4 TCMT1600--SOP-4 TCMT1600T3 (1)--SOP-16-TCMT4600 TCMT4606 SOP-16-TCMT4600T0 (1)-ABSOLUTE MAXIMUM RATINGS (Tamb = 25 C, unless otherwise specified)PARAMETERTEST CONDITIONSYMBOLVALUEUNITINPUTF orward currentIF 60mAForward surge currenttp 10 sIFSM dissipationPdiss100mWJunction temperatureTj125 C7 mmSOP-#TCMT1600, TCMT4600, Semiconductors Rev.

3 , 21-Jul-152 Document Number: 83512 For technical questions, contact: DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT Stresses in excess of the absolute maximum ratings can cause permanent damage to the device. Functional operation of the device is not implied at these or any other conditions in excess of those given in the operational sections of this document. Exposure to absolute maximum ratings for extended periods of the time can adversely affect reliability.(2)Wave soldering three cycles are allowed. Also refer to Assembly Instructions ( ).Note Minimum and maximum values are testing requirements. Typical values are characteristics of the device and are the result of engineering evaluation. Typical values are for information only and are not part of the testing emitter voltageVCEO70 VEmitter collector voltageVECO7 VCollector currentIC50mACollector peak currenttp/T = , tp 10 msICM100mAPower dissipationPdiss150mWJunction temperatureTj125 CCOUPLERAC isolation test voltage (RMS)VISO3750 VRMST otal power dissipationPtot250mWOperating ambient temperature rangeTamb-40 to +100 CStorage temperature rangeTstg-40 to +125 CSoldering temperature (1)Tsld260 CELECTRICAL CHARACTERISTICS (Tamb = 25 C, unless otherwise specified)

4 PARAMETERTEST voltageIF = 50 capacitanceVR = 0 V, f = 1 MHzCj-8-pFOUTPUTC ollector emitter voltageIC = 100 AVCEO70--VEmitter collector voltageIE = 100 AVECO7- -VCollector dark currentVCE = 20 V, IF = 0 ICEO--100nACOUPLERC ollector emitter saturation voltageIF = 10 mA, IC = 1 frequencyVCE = 5 V, IF = 10 mA,RL = 100 fc-100-kHzCapacitance ( input to output )f = 1 pFCURRENT TRANSFER RATIO (Tamb = 25 C, unless otherwise specified)PARAMETERTEST = 5 V, IF = 5 mATCMT1600 CTR80300%TCMT4600 CTR80300%TCMT4606 CTR100300%ABSOLUTE MAXIMUM RATINGS (Tamb = 25 C, unless otherwise specified)PARAMETERTEST CONDITIONSYMBOLVALUEUNITTCMT1600, TCMT4600, Semiconductors Rev. , 21-Jul-153 Document Number: 83512 For technical questions, contact: DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT Fig.

5 1 - Test Circuit, Non-Saturated OperationFig. 2 - Test Circuit, Saturated OperationFig. 3 - Switching TimesSWITCHING CHARACTERISTICS (Tamb = 25 C, unless otherwise specified)PARAMETERTEST timeVS = 5 V, IC = 2 mA, RL = 100 (see figure 1)td-3- sRise timeVS = 5 V, IC = 2 mA, RL = 100 (see figure 1)tr-3- sFall timeVS = 5 V, IC = 2 mA, RL = 100 (see figure 1) sStorage timeVS = 5 V, IC = 2 mA, RL = 100 (see figure 1) sTurn-on timeVS = 5 V, IC = 2 mA, RL = 100 (see figure 1)ton-6- sTurn-off timeVS = 5 V, IC = 2 mA, RL = 100 (see figure 1)toff-5- sTurn-on timeVS = 5 V, IF = 10 mA, RL = 1 k (see figure 2)ton-9- sTurn-off timeVS = 5 V, IF = 10 mA, RL = 1 k (see figure 2)toff-18- s100 50 Channel IIChannel IIC = 2 mA; Adjusted ThroughInput Amplitude+ 5 VIFIF0RG = 50 tptp = 50 sT= = 1 M CL = 20 pF152341 k 50 Channel IIChannel I+ 5 VIF0RG = 50 tptp = 50 sT= = 1 M CL = 20 pF15235IF = 10 mAtptt0010 %90 %100 %trtdtontstftoffIFICtpPulse durationtdDelay timetrRise timeton(= td + tr) Turn-on timetsStorage timetfFall timetoff(= ts + tf)Turn-off time96 11698 TCMT1600, TCMT4600, Semiconductors Rev.

6 , 21-Jul-154 Document Number: 83512 For technical questions, contact: DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT As per IEC 60747-5-5, , this optocoupler is suitable for safe electrical insulation only within the safety ratings. Compliance with the safety ratings shall be ensured by means of protective circuits. TYPICAL CHARACTERISTICS (Tamb = 25 C, unless otherwise specified)Fig. 4 - Total Power Dissipation vs. Ambient TemperatureFig. 5 - Forward Voltage vs. Forward CurrentSAFETY AND INSULATION RATINGSPARAMETERTEST CONDITIONSYMBOLVALUEUNITC limatic classification (according to IEC 68 part 1)55/110/21 Comparative tracking indexCTI175 Maximum rated withstanding isolation voltage40 % to 60 % RH, AC test of 1 minVISO3750 VRMSM aximum transient isolation voltageVIOTM6000 VMaximum repetitive peak isolation voltageVIORM707 VInsulation resistanceVIO = 500 V, Tamb = 100 CRIO1011 Isolation resistance (under fault conditions)VIO = 500 V, Tamb = TSIRIO109 output safety powerPSO350mWInput safety currentISI200mAInput safety temperatureTSI175 CApparent charge test voltage (method A)VIORM x = VPR, type and sample test tm = 60 s, partial discharge < 5 pCVPR1132 VpeakApparent charge test voltage (method B)

7 VIORM x = VPR, 100 % production test with tm = 1 s, partial discharge < 5 pCVPR1326 VpeakCreepage distance 5mmClearance distance 5mmInsulation thicknessDTI (pollution degree in accordance to DIN VDE 0109)205010015020025030004080120 Ptot - Total Power Dissipation (mW)Tamb - Ambient Temperature ( C)96 11700 Coupled 1 10 100 IF - Forward Current (mA) VF - Forward Voltage (V) Tamb = 110 C Tamb = 75 C Tamb = 25 C Tamb = 0 C Tamb = -55 C TCMT1600, TCMT4600, Semiconductors Rev. , 21-Jul-155 Document Number: 83512 For technical questions, contact: DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT 6 - Collector Current vs. Collector Emitter Voltage Fig. 7 - Leakage Current vs. Ambient TemperatureFig. 8 - Collector Current vs.

8 Collector Emitter VoltageFig. 9 - Normalized Current Transfer Ratio (non-saturated) TemperatureFig. 10 - Normalized Current Transfer Ratio (saturated) TemperatureFig. 11 - Collector Emitter Voltage vs. Ambient Temperature 0 5 10 15 20 25 30 35 40 45 50 55 0 1 2 3 4 5 6 7 8 9 10 IC - Collector Current (mA) VCE - Collector Emitter Voltage (non-sat) (V) IF = 30 mA IF = 35 mA IF = 1 mA IF = 20 mA IF = 15 mA IF = 10 mA IF = 5 mA IF = 25 mA 000 ICE0- Leakage Current (nA)Tamb- Ambient Temperature ( C)IF= 0 mAVCE= 40 VVCE= 24 VVCE= 12 V-60 -40 -20 020 40 60 Collector Current (mA)VCE- Collector Emitter Voltage (V)IF= 1 mAIF= 10 mAIF= 5 mAIF= 2 mA0 NCTR - Normalized CTR (non-saturated)Tamb - Ambient Temperature ( C) Normalized to CTR value: IF = 5 mA, VCE = 5 V, Tamb = 25 C IF = 5 mA -60 -40 -20 020 40 60 801201000 NCTR - Normalized CTR (sat) Tamb - Ambient Temperature ( C) IF= 5 mA Normalized to CTR value.

9 IF= 5 mA, VCE= 5 V, Tamb= 25 C-60 -40 -20 020 40 60 VCEsat - Collector Emitter Voltage (V) Tamb - Ambient Temperature ( C) Ic = 1 mA Ic = 2 mA Ic = 5 mA IF = 10 mA-60 -40 -20 020 40 60 80120100 TCMT1600, TCMT4600, Semiconductors Rev. , 21-Jul-156 Document Number: 83512 For technical questions, contact: DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT 12 - Normalized CTR (non-saturated) vs. Forward CurrentFig. 13 - Normalized CTR (saturated) vs. Forward CurrentFig. 14 - FCTR vs. Phase AngleFig. 15 - FCTR vs. Collector CurrentFig. 16 - Switching Time vs. Load Normalized CTR (NS)IF- Forward Current (mA)Tamb= 0 CTamb= 100 CTamb= 75 CTamb= -55 CTamb= 25 CNormalized to:IF = 5 mA, VCE = 5 V,Tamb = 25 Normalized CTR (sat)IF- Forward Current (mA)VCE= VNormalized to:IF= 5 mA,VCE= 5 V,Tamb= 25 CTamb= 0 CT= 75 CTamb= -55 C-Tamb= 25 CTamb= 100 Camb-160-140-120-100-80-60-40-2001 10 100 1000 Phase Angle (deg) f - Frequency (kHz) VCE= 5 V RL = 100 RL = 1000 1 10 100 1000 1 10 100 FCTR (kHz) IC (mA) VCC = 5 V 1 10 100 1000 0 5 10 15 20 ton, toff Switching Time ( s) RL - Load Resistance (k ) toff ( s) ton ( s) VCE = 5 V, IC = 2 mA TCMT1600, TCMT4600, Semiconductors Rev.

10 , 21-Jul-157 Document Number: 83512 For technical questions, contact: DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT DIMENSIONS in + footprintPin One , TCMT4600, Semiconductors Rev. , 21-Jul-158 Document Number: 83512 For technical questions, contact: DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT MARKINGPACKAGING INFORMATION (TAPE AND REEL) in millimetersFig. 17 - Tape and Reel Shipping MediumFig. 18 - Tape and Reel Packing (3000 parts per reel)MT1600V YWW 68 TCMT4600V YWW 68 Top cover 12 , TCMT4600, Semiconductors Rev. , 21-Jul-159 Document Number: 83512 For technical questions, contact: DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE.