Optocoupler, Phototransistor Output, AC Input - …

1 SFH620A, Semiconductors Rev. , 31-Aug-151 Document Number: 83675 For technical questions, contact: DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT , Phototransistor output , AC InputDESCRIPTIONThe SFH620A (DIP) and SFH6206 (SMD) feature a high current transfer ratio, low coupling capacitance and high isolation voltage. These couplers have a GaAs infrared diode emitter, which is optically coupled to a silicon planar Phototransistor detector, and is incorporated in a plastic DIP-4 or SMD coupling devices are designed for signal transmission between two electrically separated circuits. The couplers are end-stackable with mm lead spacing. Creepage and clearance distances of > 8 mm are achieved with option 6.

2 This version complies with IEC 60950 (DIN VDE 0805) for reinforced insulation to an operation voltage of 400 VRMS or Good CTR linearity depending on forward current Isolation test voltage, 5300 VRMS High collector emitter voltage, VCEO = 70 V Low saturation voltage Fast switching times Low CTR degradation Temperature stable Low coupling capacitance End-stackable, " ( mm) spacing High common-mode interference immunity Material categorization: for definitions of compliance please see AGENCY APPROVALSThe safety application model number covering all products in this datasheet is SFH620A and SHF6206. This model number should be used when consulting safety agency documents. UL1577, file no. E52744 system code H, double protection CSA 93751 BSI EN 60950, EN 60065 DIN EN 60747-5-5 (VDE 0884-5), available with option 1 CQC GB8898-2011, Additional options may be possible, please contact sales office.

3 (1)Also available in tubes; do not add T to INFORMATIONSFH620x -#X0##TPART NUMBERCTR BINPACKAGE OPTIONTAPEANDREELAGENCY CERTIFIED/PACKAGECTR (%) 10 mASFH620 ASFH6206UL, cUL, BSI40 to 12563 to 200100 to 32040 to 12563 to 200100 to 320 DIP-4 SFH620A-1 SFH620A-2 SFH620A-3---DIP-4, 400 mil, option 6 SFH620A-1X006 SFH620A-2X006 SFH620A-3X006---SMD-4, option 7-SFH620A-2X007T (1)-- --SMD-4, option 9---SFH6206-1T (1)SFH6206-2T (1)SFH6206-3T (1)VDE, UL, CUL, BSI40 to 12563 to 200100 to 32040 to 12563 to 200100 to 320 DIP-4 SFH620A-1X001 SFH620A-2X001 SFH620A-3X001---DIP-4, 400 mil, option 6-SFH620A-2X016 SFH620A-3X016---SMD-4, option 7-SFH620A-2X017T----SMD-4, option 9----SFH6206-2X001T (1)SFH6206-3X001T (1)> mm> mmDIP-# Option 7 Option 6 Option 9 SFH620A, Semiconductors Rev.

4 , 31-Aug-152 Document Number: 83675 For technical questions, contact: DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT Stresses in excess of the absolute maximum ratings can cause permanent damage to the device. Functional operation of the device is not implied at these or any other conditions in excess of those given in the operational sections of this document. Exposure to absolute maximum ratings for extended periods of the time can adversely affect reliability.(1)Refer to reflow profile for soldering conditions for surface mounted devices (SMD). Refer to wave profile for soldering conditions for through hole devices (DIP). Note Minimum and maximum values are testing requirements.

5 Typical values are characteristics of the device and are the result of engineering evaluation. Typical values are for information only and are not part of the testing requirements. Still air, coupler soldered to PCB or MAXIMUM RATINGS (Tamb = 25 C, unless otherwise specified)PARAMETERTEST CONDITIONSYMBOLVALUEUNITINPUTDC forward currentIF 60mASurge forward currenttp 10 sIFSM dissipationPdiss100mWOUTPUTC ollector emitter voltageVCEO70 VEmitter collector voltageVECO7 VCollector currentIC50mAtp 1 sIC100mAPower dissipationPdiss150mWCOUPLERT otal power dissipationPtot250mWStorage temperature rangeTstg-55 to +150 CAmbient temperature rangeTamb-55 to +100 CJunction temperatureTj100 CSoldering temperature (1)max. 10 s, dip soldering distance to seating plane mmTsld260 CELECTRICAL CHARACTERISTICS (Tamb = 25 C, unless otherwise specified)PARAMETERTEST Forward voltageIF = 60 = 0 V, f = 1 MHzCO50pFThermal resistanceRthja750K/WOUTPUTC ollector emitter capacitanceVCE = 5 V, f = 1 resistanceRthja500 C/WCOUPLERC ollector emitter saturation voltage IF = 10 mA, IC = emitter leakage currentVCE = 10 VSFH620A-1 ICEO250nASFH6206-1 ICEO250nASFH620A-2 ICEO250nASFH6206-2 ICEO250nASFH620A-3 ICEO5100nASFH6206-3 ICEO5100nASFH620A, Semiconductors Rev.

6 , 31-Aug-153 Document Number: 83675 For technical questions, contact: DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT 1 - Switching Times Linear Operation (without Saturation)Note As per DIN EN 60747-5-5, , this optocoupler is suitable for safe electrical insulation only within the safety ratings. Compliance with the safety ratings shall be ensured by means of protective TRANSFER RATIO (Tamb = 25 C, unless otherwise specified)PARAMETERTEST = 5 V, IF = 10 mASFH620A-1 CTR40125%SFH6206-1 CTR40125%SFH620A-2 CTR63200%SFH6206-2 CTR63200%SFH620A-3 CTR100320%SFH6206-3 CTR100320%VCE = 5 V, IF = 1 mASFH620A-1 CTR1330%SFH6206-1 CTR1330%SFH620A-2 CTR2245%SFH6206-2 CTR2245%SFH620A-3 CTR3470%SFH6206-3 CTR3470%SWITCHING CHARACTERISTICS (Tamb = 25 C, unless otherwise specified)

7 PARAMETERTEST timeRL = 75 , IF = 10 mA, VCC = 5 Vton3 sRise timeRL = 75 , IF = 10 mA, VCC = 5 Vtr2 sTurn-off timeRL = 75 , IF = 10 mA, VCC = 5 sFall timeRL = 75 , IF = 10 mA, VCC = 5 Vtf2 sCut-off frequencyRL = 75 , IF = 10 mA, VCC = 5 Vtctr208kHzSAFETY AND INSULATION RATINGS PARAMETERTEST CONDITIONSYMBOLVALUEUNITC limatic classificationAccording to IEC 68 part 155/115/21 Pollution degreeAccording to DIN VDE 01092 Comparative tracking index Insulation group IIIaCTI175 Maximum rated withstanding isolation voltageAccording to UL1577, t = 1 min VISO4470 VRMST ested withstanding isolation voltageAccording to UL1577, t = 1 s VISO5300 VRMSM aximum transient isolation voltageAccording to DIN EN 60747-5-5 VIOTM8000 VpeakMaximum repetitive peak isolation voltageAccording to DIN EN 60747-5-5 VIORM890 VpeakIsolation resistanceTamb = 25 C, VIO = 500 VRIO 1012 Tamb = 100 C, VIO = 500 VRIO 1011 output safety power PSO700mWInput safety current ISI400mAInput safety temperature TS175 CCreepage distanceDIP-4 7mmClearance distanceDIP-4 7mmCreepage distanceDIP-4, 400 mil, option 6 8mmClearance distanceDIP-4, 400 mil, option 6 8mmCreepage distanceSMD-4, option 7 and option 9 7mmClearance distanceSMD-4, option 7 and option 9 7mmInsulation thickness DTI VCC=5 V47 IFICSFH620A, Semiconductors Rev.

8 , 31-Aug-154 Document Number: 83675 For technical questions, contact: DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT CHARACTERISTICS (Tamb = 25 C, unless otherwise specified)Fig. 2 - Current Transfer Ratio (CTR) vs. TemperatureFig. 3 - output Characteristics (Typ.) Collector Current Emitter VoltageFig. 4 - Diode Forward Voltage (Typ.) vs. Forward CurrentFig. 5 - Transistor Capacitance (Typ.) vs. Collector Emitter VoltageFig. 6 - Permissible Pulse Handling Capability Forward Current vs. Pulse WidthFig. 7 - Permissible Power Dissipation vs. Ambient Temperature(%)103102101- 257525050TA ( C)isfh620a_01IF = 10 mA, VCC = 5 V123 ICIF3010200015105 VCE (V)isfh620a_02IF = 14 mAIF = 12 mAIF = 10 mAIF = 6 mAIF = 8 mAIF = 4 mAIF = 2 mAIF = 1 mAIC (mA) = f (IF)25 C50 C75 CIF (mA)VF (V)1020510152010-210-1100101102C (pF)Ve (V)isfh620a_04f = 1 MHzCCE10110210310410-510-410-310-210-110 0101isfh620a_05tpIFTTD = tpD = 0 cycleD = (mA)tp (s)0501001502000501007525isfh620a_06 TransistorDiodeTA ( C)Ptot (mW)SFH620A, Semiconductors Rev.

9 , 31-Aug-155 Document Number: 83675 For technical questions, contact: DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT 8 - Permissible Diode Forward Current TemperaturePACKAGE DIMENSIONS in millimetersDIP-4, Standard03060901200501007525isfh620a_07 Ptot = f (TA)IF (mA)TA ( C) one to 9 SFH620A, Semiconductors Rev. , 31-Aug-156 Document Number: 83675 For technical questions, contact: DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT , Option 6 SMD-4, Option one one , Semiconductors Rev.

10 , 31-Aug-157 Document Number: 83675 For technical questions, contact: DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT , Option 9 PACKAGE MARKING (example)Notes Only options 1 and 7 are reflected in the package marking. The VDE logo is only marked on option1 parts. Tape and reel suffix (T) is not part of the package PROFILESFig. 9 - Wave Soldering Double Wave Profile According to J-STD-020 for DIP-8 DevicesFig. 10 - Lead (Pb)-free Reflow Solder Profile According to J-STD-020 for SMD-8 one H 68 SFH620A-1V X0012 K/ssecondwavefirst wavewaveca. 5 K/s5 sfull line: typicaldotted line:process limitsTime (s)Temperature ( C)30025020015010050005010015020025094 8626 Lead temperature235 C to 260 C100 C to 130 Cca.