Parameter list Vector Control - samsebeplc.ru

1 Parameter list Vector Status1 Visualization Parameter for the current status of the converteor inverter. The converter status is, for example, determinedby the Control commands for the internal sequence Control (see Control word 1 and 2r550,r551) and by menu selection = Power section definition1 = Initialization of converter or inverter2 = Hardware initialization3 = Drive system initialization4 = Board configuration5 = Drive setting6 = Selection of several drive test functions7 = St rung8 = Start inhibt9 = Ready for ON10 = Precharging of Dc link bus11 =Ready for operation12 = Ground fault test13 = "Flying restart" is active14 = Operation15 = OFF1 is active16 = OFF3 is active17 = "DC braking" is active18 = Motor data identification at standstill is active19 = Optimization of speed controller20 = "Synchronization" active21 = : 0 Unit: -Indices: -Type: O2 Menus.

2 - Parameter menu + General parameters + Motor/encoder + Encoder data + Control /gating unit + Position Control + Diagnostics + Trace + Technology + Synchronism + Positioning- Fixed settings- Quick parameterization- Board configuration- Drive setting- Download- Upread/free access- Power section definitionr002 Rot Freq2 Visualization Parameter for the speed actual value in Hz (multiplied by the pole pair number P109 of the drive)Display quantity for the PMU parameterizing unit and the OP(see P049).In function , , : 3 Unit: HzIndices: -Type: I4 Menus: - Parameter menu + General parameters - Upread/free accessr003 Output Volts3 Visualization Parameter for the output voltage of the converter or inverter (fundamental rms)In function , : 1 Unit: VIndices: -Type: I2 Menus: - Parameter menu + General parameters - Upread/free accessr004 Output Amps4 Visualization Parameter for the output current of the converter or inverter (fundamental rms)In function , : 1 Unit: AIndices: -Type: I4 Menus.

3 - Parameter menu + General parameters - Upread/free accessr005 Output Power5 Visualization Parameter for the ouput active display value is normalized to the reference power whicis derived from the product of reference frequency P352 andreferencetorque function , : 1 Unit: %Indices: -Type: I2 Menus: - Parameter menu + General parameters - Upread/free access1 SIMOVERT MASTERDRIVES Compendium Vector ControlSiemens AG 6SE7087-6QX60 (Edition AE)ParameterDescriptionDataRead/writer00 6DC Bus Volts6 Visualization Parameter for DC link quantity for the PMU parameterizing unit and the OP (r049).In function , : 0 Unit: VIndices: -Type: I2 Menus: - Parameter menu + General parameters - Upread/free accessr007 Motor Torque7 Visualization Parameter for torque, related to the reference torque (P354) : 1 Unit: %Indices: -Type: I2 Menus: - Parameter menu + General parameters - Upread/free accessr008 Motor Parameter for thermal motor utilization (calculated value).

4 Precondition:P383 >= 100 s and no temperature sensor overload protection derived from this Parameter is only effective if sufficient cooling of the motor is : 0 Unit: %Indices: -Type: O2 Menus: - Parameter menu- Upread/free accessr009 Motor Parameter for the current motor correct display is only possible if the motor temperature is measured with a KTY84 temperature sensor or BICO Parameter P385 is softwired to a connector which provides the temperature signal in the normalization 1 =40 : P380 > 1 orP381 > 1 orP386 = 2 and P381 > 1 In function : 0 Unit: CIndices: -Type: I2 Menus: - Parameter menu + General parameters + Functions- Upread/free accessr010 Drive Parameter for the current thermal utilization of the converter or utilization is determined byan i2t calculation of the outpucurrent.

5 A value of 100 % is achieved in continuous operation with the rated a 100 % utilization is exceeded, an alarm message (A024)is tripped and the output current is reduced to 89 % of the rated : 0 Unit: %Indices: -Type: O2 Menus: - Parameter menu + General parameters - Upread/free accessr011act. MotDataSet11 Visualization Parameter for the currently active motor data = Data set 12 = Data set 23 = Data set 34 = Data set 4A motor data set is selected with Control word bits 18 and 19 The relevant BICO parameters for linking the Control word bits are P578 and function : 0 Unit: -Indices: -Type: O2 Menus: - Parameter menu + General parameters - Drive setting- Upread/free access2 SIMOVERT MASTERDRIVES Compendium Vector ControlSiemens AG 6SE7087-6QX60 (Edition AE)ParameterDescriptionDataRead/writer01 2 Active BICO DSet12 Visualization Parameter for the currently active BICO data se1 = Data set 12 = Data set 2A BICO data set is selected with Control word bit 30.

6 The relevant BICO Parameter for linking the Control word bit is function : 0 Unit: -Indices: -Type: O2 Menus: - Parameter menu + General parameters - Upread/free accessr013 Active FuncDSet13 Visualization Parameter for the currently active function =Data set 12 = Data set 23 = Data set 34 = Data set 4A function data set is selected with Control word bits 16 and 17. The relevant BICO parameters for linking the Control word bits are P576 and function : 0 Unit: -Indices: -Type: O2 Menus: - Parameter menu + General parameters - Upread/free accessr014 Setp Speed14 Visualization Parameter for the speed setpoint at the speed controller input or at the frequency input of the v/f function , , , : 1 Unit: 1/minIndices: -Type: I4 Menus: - Parameter menu + General parameters - Upread/free accessr015n(act)15 Visualization Parameter for the speed actual function , , : 1 Unit: 1/minIndices: -Type: I4 Menus.

7 - Parameter menu + General parameters - Upread/free accessP028*SrcDispPowerConn28 BICO Parameter for selecting connectors which contain a power and are to be displayed in visualization Parameter r02in (%). The connector numbers entered in the respective index are displayed in the same index of Parameter function : 0 Unit: -Indices: 5 Type: L2 ,KMenus: - Parameter menu + General parameters - Upread/free accessChangeable in: - Drive setting- Readyr029 DispPowerConn29 Visualization Parameter for displaying connectors given in P028 in (%). The connectors displayed in the respective index have been selected in the same index of Parameter P028. Normalization is determined in P352 and P354.

8 In function : 1 Unit: %Indices: 5 Type: I4 Menus: - Parameter menu + General parameters - Upread/free accessP030*Src Disp Binec30 BICO Parameter for selecting binectors which are to be shown in visualization Parameter r031. The binector numberentered in the respective index are displayed in the same index of Parameter r031. In function diagram: : 0 Unit: -Indices: 5 Type: L2 ,BMenus: - Parameter menu + General parameters - Upread/free accessChangeable in: - Drive setting- Readyr031 Display Binector31 Visualization Parameter for displaying the binectors given in P030. The binectors displayed in the respective index have been selected in the same index of Parameter function : 0 Unit: -Indices: 5 Type: O2 Menus: - Parameter menu + General parameters - Upread/free access3 SIMOVERT MASTERDRIVES Compendium Vector ControlSiemens AG 6SE7087-6QX60 (Edition AE)ParameterDescriptionDataRead/writeP03 2*Src Disp Conn32 BICO Parameter for selecting connectors which are to be displayed in visualization Parameter r033 in [%].

9 The connector numbers shown in the respective index are displayed in the same index of Parameter function : 0 Unit: -Indices: 5 Type: L2 ,K ,KMenus: - Parameter menu + General parameters - Upread/free accessChangeable in: - Drive setting- Readyr033 Display Conn33 Visualization Parameter for displaying the connectors given iP032. The connnectors displayed in the respective index have been selected in the same index of Parameter P032. Aconnector value of 4000 H or 4000 0000 H is shown at 100 %.In function : 3 Unit: %Indices: 5 Type: I4 Menus: - Parameter menu + General parameters - Upread/free accessP034*SrcDispVoltsConn34 BICO Parameter for selecting connectors which contain a voltage and are to be displayed in visualization Parameter r035 in [V].

10 The connector numbers entered in the respectiveindex are displayed in the same index of Parameter function : 0 Unit: -Indices: 5 Type: L2 ,KMenus: - Parameter menu + General parameters - Upread/free accessChangeable in: - Drive setting- Readyr035 Disp Volts Conn35 Visualization Parameter for displaying connectors given in P034 in [V]. The connectors displayed in the respective indehave been selected in the same index of Parameter P034. The normalization is specified in P351. The following methodof calculation must be used:r035 = P351 xConnector Value in [%]/100%.In function : 1 Unit: VIndices: 5 Type: I4 Menus: - Parameter menu + General parameters - Upread/free accessP036*SrcDispAmpsConn36 BICO Parameter for selecting connectors which contain a current and are to be displayed in visualization Parameter r037 in [A].