PARTS & INSTALLATION INSTRUCTIONS E-47 & E-47H …

1 Form No. 1-642R5 July,2001E - 47E - 47H1 1/2" x 10"1 1/2" x 12"2" x 12" and Ass'y. (Complete) 12 volt15516S15516S15505S1 Lift and Ass'y. (Complete) 24 volt11574215742157431 Lift Ass'y. (Unit only) 12 volt1574715747157441 Lift Ass'y. (Unit only) 24 volt21568015680156801 Harness and Fuse Ass' Starter Solenoid - 12 volt3b1544615446154461 Starter Solenoid - 24 volt40701907021070231 Ram with Hose & Fittings0581005437057521 Ram5a2214422144221441 Hose Ass'y. 1/4 x 45" 1/4 x 90 Degree Elbow7a2229122291222911 Coupler 1/4 - Male Half8a2232522325223251 Coupler Cap Low Spill90702007022070241 Ram with Hose & Fittings0581005437057521 Ram5b2214422144221441 Hose Ass'y.

2 1/4 x 45" 1/4 x 90 Degree Elbow7b2229222292222921 Coupler 1/4 - Female Half8b2232622326223261 Coupler Plug Low Spill101567015670156701 Pigtail Ass' Power Cable - 63" - RED121567215672156721 Ground Cable - 42" - BLACK130502405024050241 Power Cable - 36"141566915669156691 Weather Plug - Solenoid Wires153624836248362481 Weather Plug - Power Cables160847308473084731 Relief Valve Kit - Reservoir1567915679156791 Hardware Bag172209222092220921 Controller, Single Lever181567315673156731 Bracket for Single Lever Control192209022090220901 Decal, Single Lever Control201567615676156761 Backup Plate211567515675156751 Clamp Plate221542715427154271 Light Switch Bracket232209122091220911 Decal - Lights242031220312203122 Locknut 1/4 - 20252084120841208412 S.

3 Tapping Screw #12 - 14 x 1/2" Machine Screw 1/4 - 20 x 1" RND. S. Tapping Screw 1/4 - 14 x 3/4"282140021400214001 Lockwasher INT/Ext Tooth 5/16292183221832218321 Bushing - Split302195321953219531 Decal - Danger (Mount on Dashboard)311510215102151021 Bolt 5/16" - 18 x 1/2" Gr. 20836308364083641 Hardware Bag ( Rams)32a20146------------4 Bolt H 5/8 - 11 x 3 1/4" Gr. 532b------20147201474 Bolt H 5/8 - 11 x 3 1/2" Gr. 5332030920309203094 Locknut 5/8 - 1134------20357203572 Flatwasher 5/8 GENERAL INFORMATION:CAUTION: Always disconnect battery prior to contents against the PARTS list to determine all are correctand included. When ordering PARTS , furnish Part No.

4 , Name andDescription, Type of Hydraulic Unit and Moldboard PRECAUTIONS should be used when ELECTROTOUCH is in OPERATION and plow is in a RAISED plow to ground when vehicle is and SERVICE INFORMATION is covered on ELECTRO TOUCH Unit maintenance, refer to "Owner'sManual."Meyer Products reserves the right, under its continuing product improvement program, to change construction or design details, specificationsand prices without notice or without incurring any :1. Connect ground cable to negative side of battery for a solidconnection to Caution: Route all cables away from moving engine PARTS ,Manifolds, and sharp sheet For weather protection, tape all electrical connections at frontof The vehicle must be equipped with a "Heavy Duty Battery" (70 Amp.)

5 Hr. Min.) 550 and "Alternator" (60 amp. Min.) to obtainmaximum Follow these INSTRUCTIONS explicitly. Warranty does not apply toa Meyer product which has been negligently or improperlyassembled or & INSTALLATION INSTRUCTIONSE-47 & E-47 HMEYER ELECTRO TOUCH PARTS LISTP arts indented are included in the carton, bag or assembly under which they are indented. 2001 Printed in the Products18513 Euclid Ave. Cleveland, Ohio 44112-1084 Phone 486-1313 (Area Code a convenient location for the control switch(17). The light switch (found in light carton) can alsobe located wherever desired by using light switchbracket (22) and Self Tapping Screws (25).

6 If LightSwitch Bracket is used apply Light Decal (23).G. If the desired location is the dashboard, there aretwo methods of INSTALLATION . The first is to mount thecontrol switch directly in a 3/4" diameter hole in thedash. This is practical on dashboards that are madeof steel with no padding. On plastic dashes, installBracket (18) by drilling 2 holes in the dashboard andsecure using Round Head Machine Screws (26) andLocknuts (24). Install Back-up Plate (20) behind dashfor added stiffness. See illustration. Also applyDanger Decal (30) to To mount control to shift lever, use Bracket (18),Clamp Plate (21), Round Head Machine Screws (26)and locknuts (24).

7 See Figure After the selected bracket is installed, apply ControlSwitch Decal (19). If Light Switch Bracket (22) isused, also apply Light Decal (23).J. Use Bushing (29) where Harness (2) is routedthrough firewall and radiator support panel. Requires7/8" diameter hole. Be certain to route all wiringaround hot or moving engine PARTS , and any sharpsheet metal. Protection must be provided to guardagainst wire damage at these points. All excess orloose wire must be neatly secured using wire lead from Wiring Harness (2) must beattached to terminal in fuse panel that is activatedonly when the ignition key is "on.

8 " The three coloredwires in Harness (2) must be routed through grill toE-47 Install Starter Solenoid (3) to metal surface in enginecompartment using Screws (27). (Solenoid must begrounded to operate). Slide Weather Plugs (14 & 15)over Power Cable (11) and Ground Cable (12).Attach Red Power Cable (11) to a large terminal onStarter Solenoid (3) and route plug-end to front ofgrill area of truck. Attach Black Ground Cable (12)to negative (-) terminal of battery and route plug-end to front grill area. Attach 36" Power Cable (13)to positive (+) terminal of battery and remaininglarge terminal on Starter Solenoid (3). Attach smallBlack wire with white stripe from harness (2) to smallterminal on Starter ANGLING CYLINDERS:Attach Power Angling Cylinders (4 & 9) to Sector andA-Frame using bolts (32) and locknuts (33).

9 When using1-1/2" x 12" rams also install washer (34) at Piston endof Rams (4 & 9).Make certain Ram (4) with hose (5) and Male-half ofcoupler (7) is on Driver's side and Ram (9) with Hose(5) and Female-half of coupler (7) is on the : When the Moldboard Assembly is removed fromthe vehicle, to prevent contamination to the Couplersand Hydraulic system, the and Power AnglingHoses must be re-attached by plugging the coupler (7a,7b) together. Also where the power angling hoses wereuncoupled at the hydraulic unit, attach Coupler Cap (8a)and Plug (8b) to the female and male halves of Angling Cylinders furnished with the ELECTRO-TOUCH have been factory filled with the properamount of fluid.

10 If for any reason it is necessary to addfluid to Reservoir or to bleed the Power AnglingCylinders, proceed as follows:a. Remove Relief Valve (16) from Reservoir to add fluidduring charging and Temporarily loosen both hose connections at , Power Angling Cylinders. Base end of Cylindermust be higher than Rod end to enable trapped air Angle the Plow in both directions until fluid leaks outat both points in a steady Retighten the hose :Proper fluid level is 1-1/2" below fbe checked withthe lift arm fully retracted (down).ADDITIONAL BATTERY CONNECTIONS:a. When atteching cables to battery with side postterminals, use Adaptor Part #21976 and attach asshown in Figure Figure 2 illustrates the method of using a repair typeterminal connector which is original equipment on 1 Fig.