Example: bachelor of science
PLEASE KEEP THESE INSTRUCTIONS FOR FUTURE …
B149 installation code (Canada) or National Fuel Gas Code ANSI Z223.1.2 (USA) • To prevent injury, do not allow anyone who is unfamiliar with the stove to operate it. • To prevent injury, if the pilot or pilot and burners have gone out on their own, open the glass door and wait 5 minutes to air out before attempting to re-light the stove.
Tags:
Information
Domain:
Source:
Link to this page:
Documents from same domain
PELLET STOVE EF3 - Enviro
enviro.com6 Operating Instructions automatic Safety featuReS: Your pellet Stove has the following safety features: A. The stove will shut off when the fire goes out …
Instruction Pellet Service Manual - Enviro - Home
enviro.com4 Introduction This is a service guide designed by SHERWOOD INDUSTRIES LTD. We hope this manual will assist you to identify and correct operational concerns you might experience in
FOR INSTALLERS AND SERVICE TECHNI CIANS ONLY GAS …
enviro.comTHE UNIT WILL SOOT. Check air shutter on the burner tube (venturi). Make sure there are no leaks in the venting system. Seal venting if necessary. Improper venting configuration. Correct if necessary. Make sure that manifold (outlet). Pressure is correct. Use a manometer to check gas pressure. SEE PAGE 5 FIGURE 7.
GAS - Enviro
enviro.comSMALL GAS STOVE Westley CAST IRON GAS STOVE Westport CAST IRON / STEEL STOVE S40 LARGE GAS STOVE Berkeley Minimum distance to the stove's sides 8" 10 1/4” 11” 113/ 8" 12" Minimum distance behind the stove 4" 5” 2.5” 5" 5" Minimum alcove height to top of stove 12" 35” 32½” 285/ 8" 27½" Minimum distance corner to wall 3” 5” 2.5 ...
OWNER’S MANUAL - Enviro
enviro.comThe performance of your pellet stove is greatly affected by the type and quality of wood pellets being burned. As the heat output of various quality wood pellets differs, so will the performance and heat output of the pellet stove. CAUTION: It is important to select and use only pellets that are dry and free of dirt or any impurities
Related documents
Heat-N-Glo Fireplace
downloads.hearthnhome.comThe glass door assembly . MUST . be in place and sealed, and the trim door assembly. MUST . be in place on the fireplace before the unit can be placed into safe operation. DO NOT OPERATE . this appliance with the glass door removed, cracked, or broken. Replacement of the glass door should be performed by a licensed or qualified service person ...
ODC 3453135556 eng - Overhead Door
www.overheaddoor.comtypical sectional door installation for help-1.800.929.3667 or overheaddoor.com typical support bracket extension spring or torsion spring safe-t-beam® braces added header bracket mounting board typical 1-piece door installation 48" power cord to 120v grounded outlet 4 1 6 3 2 3 5 sectional door 1-piece door
Vissani MDFF7SS User Mannual (8.5x11)
images.thdstatic.comPre-Installation 5 6 Put the refrigerating door on bottom hinge, assemble the middle hinge, hole caps and the sleeve pipe of refrigerating door. Put the freezer door on the middle hinge, assemble the top hinge, the top hinge cover assemble the sleeve pipe of the freezer door and hole cap on the other side. Part Description Quantity A Hole cap 1 ...
SHOWER BASE DIMENSIONS AND INSTALLATION …
images.thdstatic.comShower Base Installation - Preparation 1. Ensure that the floor and the studs are at right angles. Provide a 5”×5” opening in the sub-floor for the drain. The 2” PVC waste pipe should extend above the surface of the sub-floor according to the drain installation instructions and the height of the Shower base. Refer to the product drawings and
CLASSIC REFRIGERATION USE AND CARE GUIDE
www.subzero-wolf.comGlass shelves should warm to room temperature before immersing in warm water. Glass shelf removal Refrigerator Storage STORAGE DRAWERS To remove a storage drawer, pull forward until the drawer stops. Lift the front of the drawer slightly, then pull forward. Refer to the illustration below. For French door models, the drawer slides may need to be
ICC PEI LLC
p-e-i.com5. For Fire Resistance details and construction methods, refer to UL Design #U415 System A and the USG installation instructions. Two-Hour Cavity Shaft Wall (Non-Load Bearing), See Figure 2 1. A minimum 2-1/2-in deep 24 gauge floor and ceiling J-runners, attached to structure as described above.
Rocket® - Home Cleaning Products by Shark®
m.sharkclean.comdoor on the cord, pull the cord around sharp corners, or leave the cord near heated surfaces 13. DO NOT put any objects into nozzle or accessory openings DO NOT use with any opening blocked; keep free of dust, lint, hair, and anything that may reduce airflow 4. 1 DO NOT use if nozzle or accessory airflow is restricted If the air