Power-Assisted Bicycle - Land Transport Authority
when overtaking, to avoid a collision. Avoid shining your lights onto the face of other path users. Keep both hands on the handlebars. Signal your intention to change course or make a turn ahead of time. Ride on cycling paths and bicycle crossings when available. Park your device at designated parking places such as bicycle racks and yellow boxes.
Tags:
Information
Domain:
Source:
Link to this page:
Please notify us if you found a problem with this document:
Documents from same domain
E-Scooter
www.lta.gov.sg1.3.1 Non-Motorised Bicycles A bicycle, also called a bike or cycle, is a human-powered or motor-powered, pedal-driven vehicle, having two wheels attached to a frame, one behind the other. a) c) b) d) e) Road Bicycles Mountain Bicycles Track Bicycles / Fixed Gear Bicycles Hybrid Bicycles Foldable Bicycles Types of non-motorised bicycles:
YOUR GUIDE TOINTRA-TOWN CYCLING - Land …
www.lta.gov.sg5 Before you set off… Attire Wear bright visible clothing to ensure you are seen especially during the hours of darkness. Wear cycling safety helmet.
Guide, Your, Town, Your guide tointra town cycling, Tointra, Cycling
ENGINEERING GROUP CIVIL DESIGN CRITERIA FOR ROAD …
www.lta.gov.sgengineering group civil design criteria for road and rail transit systems e/gd/09/106/a1 controlled document a1 feb 2010 ... chapter 11 station and tunnel services for rail projects ... chapter 21 lighting …
Design, Road, Engineering, Tunnel, Group, Criteria, Lighting, Civil, Engineering group civil design criteria
ENGINEERING GROUP CIVIL DESIGN CRITERIA FOR ROAD …
www.lta.gov.sg7.6 PERMANENT TUNNEL LININGS REQUIREMENTS 7.6.1 Cast In-situ & Segmental Permanent Tunnel Liningsl 7.6.2 Additional Requirements for Segmental Linings 7.7 TEMPORARY TUNNEL LININGS REQUIREMENTS 7.8 SPRAYED CONCRETE LININGS (SCL) 7.9 SUPPORT SYSTEM IN ROCK 7.10 DETAILING 7.10.1 Fixings 7.10.2 Taper Rings 7.10.3 …
Design, Engineering, Tunnel, Group, Criteria, Civil, Lining, Tunnel lining, Engineering group civil design criteria
ENGINEERING GROUP MATERIALS & WORKMANSHIP …
www.lta.gov.sg7.3 soil improvement using jet grouting 7.4 deep soil mixing (dsm) 7.5 lime or chemico-lime piles . ... 9.15 tape extensometer 9.16 vibrating wire piezometers 9.17 casagrande piezometer standpipe 9.18 water standpipes 9.19 vibration meter 9.20 temperature sensor 9.21 strain gauge
Materials and Workmanship Specification For Architectural ...
www.lta.gov.sg60 Metals and Prefinishes 1-7 70 Heavy Duty Galvanized Coatings 1-4 ... Retain quality records for 7 years from the date of the final certificate unless identified otherwise in the schedule below. ... Tests carried out on an item identical with a production item, before delivery to the site. - Production tests: Tests carried out on the ...
SECTION 4 COMMUTER FACILITIES DESIGN REQUIREMENTS
www.lta.gov.sgand mitigation provisions shall be catered for prior to the construction of the bus interchange. 2.1.4 Design Principles and Considerations (a) All design principles and requirements outlined in all other relevant sections of the ADC shall be complied. Specifically; i. Interfacing development requirements in ADC Section 2 – Chapter 10,
Section 2 ARCHITECTURAL DESIGN REQUIREMENTS
www.lta.gov.sgDoors astride the tactile route shall be automatic or permanently fixed open. Automatic doors shall be sliding in preference to swing doors. All doors accessed by the public shall require a maximum force of 22N to open or close. Any straight portion of an underground paid link between two MRT Stations which is 75m or greater in
Land Transport Authority (LTA)
www.lta.gov.sgsupport for cantilever directional signs (sheet 3 of 3) typical steel brackets for 4.5m height limit sign (900mm x 900mm) support for traffic sign (for arterial & expressway) ... traffic informatory signs (sheet 16 of 17) traffic informatory signs (sheet 17 of 17) traffic informatory signs
LTA ANNUAL REPORT 2020/21
www.lta.gov.sg4 Goh Teck Seng Deputy Chief Executive, Corporate & Development 6 Yeo Teck Guan Senior Group Director, Public Transport 8 Chan Boon Fui Group Director, Active Mobility 9 Paul Fok Chief Engineer (Civil) 10 Helen Lim Group Director, Corporate Communications 5 Sim Wee Meng Senior Group Director, Rail Group Director, Rail Infrastructure & Expansion ...
Related documents
A Practical Guide to Computer Network & Internet …
baburd.com.np11 Basic Frame Relay Implementation with PVC 54 12 DNS, Web, DHCP, FTP server configuration 58 ... cable managers, racks, CAT6 straight and crossover wiring standards, LAN meter/tester, RJ-45) Network Hardware: Crimper/clamper, RJ-45 jack male/female, LAN/Cable tester, UTP, Fiber cable, ... switches reduce traffic and divide the collision ...
Guide, Network, Computer, Practical, Rack, Internet, Frame, Collision, Practical guide to computer network amp internet
E-Scooter - Land Transport Authority
www.lta.gov.sgwhen overtaking, to avoid a collision. Avoid shining your lights onto the face of other path users. Keep both hands on the handlebars. Signal your intention to change course or make a turn ahead of time. Ride on cycling paths and bicycle crossings when available. Park your device at designated parking places such as bicycle racks and yellow boxes.
Guide for Unpacking Shipping Containers - SafeWork NSW
www.safework.nsw.gov.auracks, crates, wrapping, strapping or a combination of these • goods are packed on pallets or slip-sheets to enable the use of a forklift to unload. Bulk bags may also be appropriate • each load of sheet material is individually secured on an A-Frame. If you …
NPR 45/55-155 TRADEPACK - Isuzu
www.isuzu.com.auCHASSIS FRAME TYPE Cold rivetted ladder frame. SAPH440 steel sidemembers. Parallel side rails and rivetless top flange. DIMENSIONS Side rail (mm): 216 x 70 x 6.0 Rear frame width (mm): 850 FUEL TANK TYPE Frame mounted steel fuel tank CAPACITY 100L FUEL CAP Lockable ELECTRICAL SYSTEM TYPE 24 volt ALTERNATOR 90 amp STARTER MOTOR …
Subject: Wheel Alignment Specifications, Requirements and ...
www.genuinegmparts.com• Racks must be kept level to within 1.6 mm (1/16 in). • If any instrument that is part of the alignment machine is dropped or damaged in some way, check the calibration immediately. Check with the manufacturer of your specific equipment for their recommended service/calibration schedule. Wheel Alignment Process