Programming and Installation Instructions

1 Programming and Installation InstructionsPassed ISO9001-2000 international system ratificationTMFEATURES Waterproof seals protecting electronic components Backlit keypad for use in low light Up to 10 changeable codes including passage, user and master levels Deadlatch assembly with adjustable backset DIY Installation ( Instructions included) LED indicators for code entry 50 event audit trail recording Anti spy code encryption Low battery warning with emergency power jump overrideACCESS code INSTRUCTIONSThe YL-99 electronic lock is capable of storing up to 10 accesscodes; 1 Master code , 1 Passage code and 8 user codes are allocated a starting number or sequencenumber. The master code is 0 , the passage code is 9 andthe user codes are 1-8 . The master code must be set up in order to input user CODEThe master code is the most important code in the series as itis needed to set up all user codes and the passage codes can be a maximum of 15 digits including theallocated sequence allocated sequence number for the master code is 0 ,therefore you must ensure this is the first digit of your codeand the remainder may be any combination of digits from 0-9.

2 The manufacturers default code is 0123 .To unlock the lock, enter the code 0123 and press the # key. The lock will sound and the green indicator will light. Thehandle is unlocked while the beep is sounding and will returnto the locked position once the beep THE MASTER CODEStep the default master code ( 0123 ) or the currentmaster code , and press the # until the beeping sound stops but the blue backlightremains a new master code that starts with 0 and press the * two beeps are heard the new master code has beensaved : Door should always be ajar when adding /changing THE MASTER CODEThe reset button is located on the battery pack andshould only be used when the master code is lost orforgotten. Press and hold the reset button for fiveseconds until three beeps are heard. The master codewill return to the manufacturer default code 0123 . user CODES AND PASSAGE CODESThe user and passage codes can be any number andcombination of 0 - 9 with a maximum of 15 digits.

3 Only the master code can have 0 as the first digit andonly the passage code can have 9 as the first THE user CODES AND PASSAGE CODEStep the current master code and press the # until the beeping sound stops and the bluebacklight remains a new user code beginning with that codessequence number and press the * key. the firstuser code will begin with 1 .Once you hear two beeps the first user code has beensaved into the the second user code starting with sequencenumber 2 and press the * key. Once you hear two beeps the second user code hasbeen saved into the THE user CODES AND PASSAGE code contd ..Repeat these steps until all eight user codes and thepassage code have been successfully set. Note: Each user code must be entered while the bluebacklight is on. If light goes out, you must re-enter themaster code to unlock the lock user CODESIn addition to the master code , each user code has theability to change their own the user code you want to change and press the # the beep stops and before the blue backlight goesoff, enter the new user code and press the * key.

4 (Eg. Ifuser one is resetting their code , the new code mustagain begin with 1 )Once you hear two beeps the new user code has beensaved into the lock. Note: Door should always be ajar when adding /changing A user CODEIf you want to delete alluser the master code and press the # key. Step the beep stops and before the blue backlight goesoff, enter 0 five times and press the * you hear two beeps all codes will be erased andonly the master code will be able to operate the you want to delete an individualuser the master code and press the # key. Step the beep stops and before the blue backlight goesoff, enter 0000 and the sequence number of the codeyou want to delete and press the * key. (Eg. To deletecode one - enter 00001 )Once you hear several beeps, the user code selectedwill be this procedure for any other user codes you wishto MODE - ONE DIGIT ACCESSThe YL-99 has the ability to be set to passage mode byentering a passage passage mode, all users can press any key to openthe door without requiring a user to enter passage modeStep the passage code (beginning with sequencenumber 9 ) then press #.

5 Step the beep stops and before the blue backlight goesoff, press * then # in quick you hear two beeps the lock is in passage to cancel passage modeStep any key to activate the the beep stops and before the blue backlight goesoff, press * then # in quick you hear two beeps passage mode is function is an added security feature which is aimedat preventing codes being observed while the first digit of the code you want to any sequence of digits to confuse the the balance of the user code , followed by the # : user code is 83557373 . Enter the first digit: 8 Enter any digits to confuse the observer: 564778458 Enter the balance of the original user code : 3557373and press # user code AUDIT TRAILThe lock will record the last 50 events. Please contact your distributor for more INFORMATIONThe lock requires four AAA alkaline batteries which arehoused in the internal lock has a low battery indicator which whenunlocking the door will sound a continuous beep,followed by a single batteries should be installed within approximatelytwo battery life is approximately 180 days and alltime measurements are calculated on twenty uses the batteries are completely dead, you can use theemergency backup battery pack (supplied) to powerthe lock, however ensure that the batteries in the lockare replaced COMPONENTSA : Outside KnobB : Outside Rose PlateC : Latch AssemblyD : Inside Rose PlateE : Mounting ScrewsF : Battery BoxG : Inside Knob CoverH : Cover Plate ScrewsJ : Strike PlateK : Wrought BoxL : Latch FaceplateM : LED IndicatorN : KeypadP : Emergency Power JackQ : Reset KeyNPACLJKFQGEDBMH6 Installation INSTRUCTIONSStep 1.

6 Mark DoorUsing template, markhole on both sides ofdoor at requiredbackset, then marklatch hole on 3. Install LatchInsert latch into hole andmark a line around edge oflatch plate and removelatch. (Fig. 3a)Chisel approx. 3mm deep oruntil latch plate sits flush withdoor edge. (Fig. 3b)Insert latch then drill 2 x 3mmholes for mounting screwsand fasten latch. (Fig. 3c)Step 2. Drill HolesBore a 54mm hole ondoor face, then drill25mm hole in dooredge to intersect withcenter of 54mm : Drill 54mm holefrom both sides ofdoor to stop woodsplintering(Fig. 3a)(Fig. 3b)(Fig. 3c)78 Step 5. Install OutsideKnobFeed the power cablethrough latch and guidespindle through untiloutside rose sits 4. Install StrikeClose door and mark horizontal centre of latch on to doorframe. Mark vertical line where door edge meets frameand measure in half of door thickness to find verticalcentre. (Fig. 4a) Extend both lines until they intersect and drill a 25mm holeto 15mm strike plate and mark around frame to approx depth or until strike sits 2 x 3mm screw holes and fix strike to frame.

7 (Fig. 4b)(Fig. 4a)(Fig. 4b)Step 6. Install Inside KnobFeed power cable throughhole in knob and guidespindle into handle. (Fig 6a)Screw inside knob to outsideknob using mounting screws.(Fig. 6b)Step 7. Plug in Battery BoxInsert power cable into batterybox and position box in linewith cover screw 8. Install Inside CoverPlatePosition cover plate overbattery box and align withscrew screws to secure cover plate to inside knob.(Fig. 6a)(Fig. 6b)9 WARRANTY TERMS and PROCEDURER etain your receipt as proof of purchase. Failure to retain proof of purchase voids this Centurion code LockTMis covered by a 12 month replacement Warranty. Should your code LockTMrequire replacement during this time due to faulty performance please return the complete unit, with (theoriginal or a copy of) your receipt, to receive a new Centurion code LockTM. The 12 month replacementWarranty does not cover malfunctions due to incorrect Installation of the Centurion code Warranty applies to the original purchaser when the code LockTMunit is purchased from an AuthorisedDealer of Centurion code LockTM.

8 It is not transferrable or International Wholesalers Pte. Ltd. will not cover the cost of removal or re- Installation of theCenturion code LockTM. Centurion International Wholesalers Pte. Ltd. will not cover the cost of transport of theunit to and from your Authorised code template to door, aligning fold correctly on door edge. Distributed by:Centurion International Wholesalers Pte. Horne Road #02-01 Singapore