RJP-301B Remote Jack Pack - LG Electronics

1 RJP-301 BRemote Jack PackInstallation & Setup GuideWarranty Copyright 2009, LG Electronics , Customer Support/Service, please call: exclamation point within an equilateral triangle is intended to alert the user to the presenceof important operating and maintenance (servicing) instructions in the literature accompanyingthe :TO REDUCE THE RISK OF ELECTRIC SHOCK - - USE ONLY INDOORSATTENTION:RISQUE DE CHOCS LECTRIQUE - - POUR installation L INT RIEUR SEULEMENTWARNING:TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS PRODUCT TO RAIN OR shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be placed on the :L appareil ne doit pas tre expos des gouttements d eau ou des claboussures et de plus qu aucun objet rempli de liquide tel que des vases ne doit tre plac sur l INFORMATION:This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential equipment generates, uses and can radiate radio frequency energy and, if not installed and usedin accordance with the instruction manual, may cause harmful interference to radio , there is no guarantee that interference will not occur in a particular installation .

2 If thisequipment does cause harmful interference to radio or television reception, which can be determinedby turning the equipment off and on, the user is encouraged to try to correct the interference by oneor more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiveris connected. Consult the dealer or an experienced radio/TV technician for :Do not attempt to modify this product in any way (except as noted herein) without written authorization from LG Electronics , Inc. Unauthorized modification could void the user sauthority to operate this :The responsible party for this product s compliance is:LG Electronics , Inc., 2000 Millbrook DriveLincolnshire, IL 60069, USA Phone: and Distributed in the United States by LG Electronics , Millbrook Drive, Lincolnshire, IL 60069 Copyright 2009, LG Electronics , Warnings.

3 2 Table of Contents .. 3 Overview .. 4 - 5 Accessories ..6-7 InstallationInstallation in Wall Cutout .. 8 Installer Connections .. 9 installation Mixed Signal Breakout Cable ..10 Connections to TV Display Panel .. 11 End-User OperationEnd-User Connections Overview ..12 End-User Multi-Media Interface Connections .. 13 End-User Connectable External Source Devices .. 14 Specifications .. 15 TroubleshootingTroubleshooting .. 16 Troubleshooting Flow Chart .. 17 RJP-301B Scaler RJP Supported Timing List .. 18 Quick Setup Guide .. 19 Warranty .. Back CoverTable of Contents34 OverviewThe Remote Jack Pack (RJP) contains circuitry to determine the presence of a signalat each input jack.(Note: Audio In, Audio In L-R and Video In inputs detect the presence of the insertedplug, regardless if a signal is present or not.)When a source is detected, its priority is compared to the priority of other sourceswhich may be present. If the newly-connected active source is of higher priority thanthe existing source(s), the RJP directs the TV display panel to that and audio are monitored and switched is supplied to the RJP by the TV display panel via the control signal CAUTION:Since the end-user jack panel is exposed, use extreme caution whencleaning.

4 Do not use liquid cleaners on the connections panel. Donot allow liquids to be spilled, sprayed onto or otherwise come intocontact with the connections panel on both the end-user side andthe installer side. Clean with a slightly damp installed right in the room where guests will stay, the LG RemoteJack Pack, (RJP) multi-media interface is available to end-users to connect audio,video and computer devices to hear and view on the in-room TV display RJP can be set up to interface with the TV display panel to show the imageand/or sound from a portable DVD/CD Player, Camcorder, MP-3 Player, Notebookcomputer, or portable Video Game Player. Or, devices with digital video outputsuch as DVD players. If the end-user does not connect any devices, then theinroom TV display panel will remain on the source selected. When the end-userconnects a device, the interface switches the TV display panel to the new RJP interface is designed to be able to process audio from one source, andvideo separately from a different source, if required.

5 (The end-user can work on alaptop computer while listening to music from an MP-3 player.) However, onlyone audio and one video source can be heard/seen at the same end-user can simply plug in its Audio/Video cable(s) to the RJP input jack(s)and turn the device on. The RJP completes the connection between the newlyconnected audio and/or video source and the TV display panel. No end-usermenus are involved, all connections are made directly to the RJP continually monitors its source inputs. When a signal is detected, (adevice is plugged into one of the RJP inputs) the interface sends a message tothe TV display panel to switch to the newly-connected source (if the new sourceis of higher priority). The interface allows only the higher priority audio andvideo to be heard and seen on the TV display panel. The control cable supplies12 Volt DC power from the TV display panel to operate the that the following accessories are included with your AccessoriesMixed Signal Cable AssemblyInstallation & Setup GuideDigital Video ExtenderCable ( feet)Side Cover (2EA)Option Extras7 Mixed Signal Breakout CableMixed Signal Breakout Power Cable (Left/Right) Cable (8-pin RJ-45) Video CableGender Signal Cable (L - R) PowerCable8 installation in Wall CutoutallWWallWallThe RJP can only be installed in a vertical position into thecutout provided in the wall.

6 Vertical mounting in the cutoutis required so that a liquid will not be able to flow into theRJP. The Digital Video cable will need to be connected to theRJP. Route Digital Video cable to avoid damage fromchaffing, binding etc. The RJP must onlybe installed in the cutoutopening. It will then need to be secured with the two retainer clipsand machine screws : The connector set with right angle connectors is for connectingto the Instructions1. Route Digital Video Connect Digital Video cableto Preset retainer screw/clips to vertical position to pass throughwall cutout Insert the RJP into the wall cutout Rotate screws to position clips horizontally to engage wall Tighten screws provided to hold the RJP securely in place. Check to assure that the RJP is securely Replace screw : The Digital Video cableshould be handled care-fully to avoid damage, as it is routed between displaypanel and the : The actual appearance of the cable, cabinet, mounting hardware etc., may be different than shown inthese ConnectionsMixed Signal outAUDIOOUTiPod DOCK PORTA udio Output Jack(For future)Connect to Audio input on TVdisplay Signal CableMixed Signal Cable from MixedSignal Breakout Cable assemblymust connect to Mixed SignalOut damage will RJP cables listed below are to be connected to the TV display panel and external : Be sure the TV display panel power is turned off before attempting to connect the RJPcables to the TV display Dock Port(10-Pin RJ-50 For future)For future iPod Dock Connectionand USB Dock(Optional)1010 installation Mixed Signal Breakout CableCAUTION: Be sure power is turned off before attempting to connect the RJP to the TV : The actual appearance of the cable, cabinet, hardware etc.

7 , may be different than shown in Take off the two-sided tape that isattached to the Mixed Signal Attach the Mixed Signal Breakout cableto TV display panel on the Connect the Mixed Signal cable to MixedSignal Breakout Connect the Mixed Signal Breakoutcable to the TV display to TV Display PanelAfter completing connections between the RJP and the TV display panel, be sure the installer menu items havebeen updated to enable the RJP. Installer Menu item 040 Auto Camport needs to be set to 000 and 093 RJPA vailable needs to be set to 005 or 006. (See TV installation guide for complete instructions on new TV installations.) A brief description of each of theavailable RJP connections is provided Power Cable(Future Use)USB Cable(Future Use)Digital VideoCableAudio Cable(L-R)ControlCable-TV/STB Installer Menu Item 093 RJP Available must have options 005 and 006 to be sure to make all RJP connections beforesetting installer : -The actual appearance of the TV display panelconnections etc.

8 , may be different than shownin this Menu Item 093 RJP Available(HDMI) for HDMI set to005(Digital video & Audio) for DVI set to006iPod Dock(Optional)12 The end-user simply plugs a device such as a laptop computer with the appropriatecables, as shown in the example, into the RJP connection panel. The Remote JackPack senses the new source connection and switches the TV to the newly-connectedsource. The device s sound and image are then presented on the in-room TV displaypanel. The TV display panel adjusts automatically to the computer output the laptop is disconnected, the interface directs the TV to revert back to theprevious source for video and end-user has severalaudio/video connectionoptions available for connect-ing external devices. Theguest/user can connect aportable DVD Player, CDPlayer, Camcorder, MP-3 Player, Notebook Computer,Portable Video Game Player, end-user could connectand hear audio from onedevice and connect and viewvideo from a different RJP offers two differentstereo audio input jacks toaccommodate various enduserdevices.

9 However, only thehigher priority audio sourcewill be selected and , multiple videoinputs are available, but onlythe higher priority videosource will be selected anddisplayed. (See page 13 inputpriorities.) AUDIO INVIDEO INAUDIO INL RPC VIDEO INDIGITAL VIDEO INToday'sReportToday'sReportTypicalIn-Ro om TVDisplay PanelEnd-UserConnection PanelMounted on WallEnd-User Connections Overview1213 End-User Multi-Media Interface ConnectionsDigital Video Input PortConnection for digitalvideo sources. (portableDVD)PC Video (RGB) Input PortConnection for PC Input JacksConnection for Left-RightAudio/composite mm Stereo AudioInput JackConnection for MP-3 playeror PC audio.(Note: Audio In, Audio In L-R and Video In inputs detect the presence of an inserted plug,regardless if a signal is present or not.)AUDIO INAUDIO INVIDEO INPC VIDEO INDIGITAL VIDEO INEnd-User Audio/Video Input PrioritiesNote: The highest priority is listed Inputs/Sources1st. mm Stereo Audio Jack2nd. Left - Right Audio Jacks3rd.

10 Digital Video Audio4th. TV Display Panel Tuner Audio (Audio Default)Video Inputs1st. Digital Video2nd. PC Video3rd. Video Composite jack4th. TV Display Panel Tuner Video (Video Default)14 End-User Connectable External Source Devices PC Laptop/Notebook Computers Portable Video Game Players Portable DVD/CD Players Camcorders Digital Cameras MP-3 Audio PlayersThe End-User Can Connect:Examples of devices a guest/end-usercan connect are shown to the available to the hotel s guests, a multi-media interface to the in-room TV display panel. Audio/Videoinput jacks are provided for guest devices such as DVD/CD Players, Laptop Computers, Camcorders, Connections(RJP Back)Mixed Signal OutMixed Signal Connector(only connect to Mixed Signal Breakout Cable)iPod Dock Port10-Pin RJ-50 Audio Stereo Audio Jack(TV Display Back)Mixed Signal Breakout Digital Video CableCable Audio L-R Control Cable (8-pin RJ-45)Supplied Accessories List(Cable Assembly) Mixed Signal Cable Assembly ( ft)(Misc.)