Example: bachelor of science
SAFETY AND PROCEDURAL REQUIREMENTS FOR TYPE …
(dedicated, bi-fuel & dual fuel) (version 5) and ais-028 code of practice for use of cng/bio-cng/lng fuel in internal combustion engined vehicles (version 5) printed by the automotive research association of india p.b. no. 832, pune 411 004 on behalf of automotive industry standards committee under
Tags:
Information
Domain:
Source:
Link to this page:
Documents from same domain
Fire Detection and Alarm System (FDAS) & Fire Detection ...
hmr.araiindia.comand design of the control or of the unit on which the fire detection and alarm system acts. 2.1.3 A vehicle representative of the type to be approved shall be submitted to
Performance Requirements and Test Procedures of Braking ...
hmr.araiindia.comPerformance Requirements and Test Procedures of Braking Systems for ... ISO 6016::2008 Earth-moving machinery-Methods of measuring the weights of whole machines, their equipment and components ... Energy-absorption device normally used to control machine speed.
AUTOMOTIVE INDUSTRY STANDARD - ARAI India
hmr.araiindia.comIEC 60364-4-41:2005 Low-voltage electrical installations – Part 4-41: Protection for safety – Protection against electric shock. IS/IEC 60529: 2001 Degrees of protection provided by enclosures (IP Code). IS 15382 (Part 1): 2014/ IEC 60664-1:2007 Insulation coordination for equipment within low-
Electric Power Train Vehicles - CMVR Type Approval for ...
hmr.araiindia.comAnnex: A Requirements of Brake and Braking Systems for Electric Power Train Vehicles 5/19 Annex: B Proposed Amendments to IS 14464: 1999 for Braking System to incorporate the Features for 3 Wheelers of 1 to 1.5T GVW 7/19 Annex: C Definitions 9/19 Annex: D Criteria for Extension 15/19 Annex: E Delhi Driving Cycle for Buses 16/19
AUTOMOTIVE INDUSTRY STANDARD - ARAI India
hmr.araiindia.com3.3 Braking System – The combination of parts whose function is progressively to reduce the speed of a moving vehicle or bring it to a halt, or to keep it stationary, if it is already halted; these functions are specified in 5.1.2.
AUTOMOTIVE VEHICLES - REQUIREMENTS FOR …
hmr.araiindia.comAnnex 10 Method(s) of testing for emission of voltage changes, voltage fluctuations and flicker on AC power lines from vehicle. 102/149 Annex 11 Method(s) of testing for emission of radiofrequency conducted disturbances on AC or DC power lines from vehicles. 105/149 Annex 12 Method(s) of testing for emission of radiofrequency
Specific Requirements for Electric Power Train of Vehicles
hmr.araiindia.comtogether, whose potential is taken as reference. 2.14. "Electrical circuit" means an assembly of connected live parts which is designed to be electrically energized in normal operation. 2.15. "Electrical protection barrier" means the part providing protection against direct contact to the high voltage live parts. 2.16.
AUTOMOTIVE INDUSTRY STANDARD - ARAI India
hmr.araiindia.comAUTOMOTIVE INDUSTRY STANDARD Test Method, Testing Equipment and Related Procedures for Type Approval and Conformity of Production (COP) Testing of L2 category Vehicles for Bharat Stage VI emission norms as per CMV Rules 115, 116 and 126 PRINTED BY THE AUTOMOTIVE RESEARCH ASSOCIATION OF INDIA P.B. NO. 832, PUNE 411 004 ON …
AUTOMOTIVE INDUSTRY STANDARD - ARAI India
hmr.araiindia.com1.2 If a vehicle is tested for type approval on chassis dynamometer having reference mass up to 2,610 kg, manufacturer may seek type approval extensions up to reference mass of 2,840 kg for its variants, even if intended variant GVW exceeds beyond 3,500 kg. This Part should be read in conjunction with applicable Gazette
AUTOMOTIVE INDUSTRY STANDARD - ARAI India
hmr.araiindia.comVI) emission norms for 2, 3 and 4 wheeled vehicles. The Committee Composition for formulation of this standard is given in Annexure 1 After approval of the standard by SCOE, The Automotive Research Association of India, (ARAI), Pune, being the Secretariat of the AIS Committee, has published this standard.
Related documents
Power Trim and Tilt Systems - West Virginia University
web.statler.wvu.eduDual Solenoid System Pump Protection A dual solenoid trim pump is generally usedIn each system, a bi-metal switch built into the when an in-handle trim control is required or whenbrush lead protects the pump motor from the harness length would cause an excessive voltageoverheating. If the motor continues to operate after drop.
BOOST CONTROL INSTRUCTIONS - Holley
documents.holley.comNov 07, 2012 · people running dual port wastegates we recommend using the dual Holley solenoid setup with a sensor dedicated to measuring dome pressure. We also recommend using PWM- outputs to drive the solenoids. If you’d rather use a PWM+ output, use the ones on the J2B connector. The other PWM+ outputs (the only ones
V-316 SERIES - Versa Products
www.versa-valves.comSolenoid-Pilot Design Direct acting valve integrated on pilot valve The V-316 Series solenoid valve utilizes a high performance solenoid-pilot design. This design utilizes available media pressure/force to shift valve assuring positive shifting. This design also produces the lowest wattage ratings in the industry. High Performance Solenoid
MG996R High Torque Metal Gear Dual Ball Bearing Servo
www.electronicoscaldas.comMetal Gear Dual Ball Bearing Servo This High-Torque MG996R Digital Servo features metal gearing resulting in extra high 10kg stalling torque in a tiny package. The MG996R is essentially an upgraded version of the famous MG995 servo, and features upgraded shock-proofing and a redesigned PCB and IC
Over 40 New Products in this Catalogue - Sun Hydraulics
www.sunhydraulics.comsolenoid, pneumatic or manual valve to be fitted into the cartridge to select the valve in the open or closed condition. Page 107: The DV*N-8 is a vent-to-operate two-position two-way, normally closed directional valve with a T-8A cavity in the end and external drain. This enables a Sun pilot solenoid, pneumatic or manual valve to be fitted ...