Section 4: Metal Products, Machinery and ranspo …

1 Section 4: Metal Products, Machinery and General List of Activities Eligible for Investment Promotion Transport equipment Activities Conditions Incentives Division Manufacture of Metal products including Metal parts Products from Metal or Project must have sintering process. A3 3. alloy powder Metal products or Metal 3. Project must have Metal forming process A3. parts continuing from iron/steel casting process (using induction furnace) or iron/steel forging process, machining and stamping within the same project. Other Metal products 1. Continuous forming process from including other Metal pressing, pulling casting or forging of A4 3.

2 Parts non-ferrous Metal within the same project. 2. Forming process, machining and B1. stamping. Surface treatment or anodized surface treatment (except coating or coloring treatment for decoration purpose). Plating, Coating, A4 3. modifying or changing the surface using Advanced Technologies Plating, Coating, B1 3. modifying or changing the surface using Basic Technologies Heat Treatment Cyanide is prohibited in the process A4 3. of heat treatment. Manufacture of multi-purpose 1. Project must have forming process of A4 2. engines and equipment main engine parts, cylinder head, crank case, crankshaft, camshaft, connecting rod, piston and flywheel.

3 B1. 2. Assembling of multipurpose engine or equipment . Manufacture of Machinery , equipment and parts 2. Automation Machinery and/ or automation equipment with engineering design Activities Conditions Incentives Division General List of Activities Eligible for Investment Promotion Automation A1 2. Machinery and/or automation equipment with engineering design, including automation system integration and control system configuration Automation A2 2. Machinery and/or automation equipment with engineering design, including control system configuration Machinery , equipment Projects must have part forming A3 2.

4 And parts and/or repair process and/or with engineering of mould and die design. Assembling of Projects must have assembling A4 2. Machinery and process as approved by the Board. Machinery equipment A3 2. Assembling of Robots or Automation equipment and/or Automation Parts Manufacture of general automobile Not eligible for merit-based incentives. B1 2. Manufacture of automobile engines Manufacture of automobile 1. Must have forming process of not less A3 2. engines than 4 out of 5 parts as follows: Cylinder Head, Cylinder Block, Crankshaft, Camshaft and Connecting Rod. 2. A4. 2. Must have engine assembly process A3 2.

5 Manufacture of motorcycle 1. Must have forming process of not less engines than 4 out of 5 parts, as follows: Cylinder Head, Cylinder Block, Crankshaft, Camshaft and Connecting Rod. Must have forming process of not less than 4 out of 6 parts for manufacturing engine that have a cylinder capacity starting from 248 cc. but not exceeding 500 cc. Activities Conditions Incentives Division General List of Activities Eligible for Investment Promotion Must have forming process of not less than 2 out of 6 parts for manufacturing of engine that have a cylinder capacity of 500 cc. or more. 2.

6 Must have engine assembly process. A4. Manufacture of vehicle parts Manufacture of vehicle A2 2. parts using high technology including: Substrate for Catalytic A2 2. Converter Electronic Fuel Injection A2 2. System A2 2. Automotive Transmission Electronic Control Unit A2 2. (ECU). Manufacture of 2. automobile safety and energy-saving parts A2 2. Anti-Lock Brake System (ABS) or Electronic Brake Force Distribution (EBD). Electronic A2 2. Stability Control (ESC). Regenerative 2. A2. Braking System Idling Stop A2 2. System Autonomous A2 2. Emergency Braking System Manufacture of parts for Hybrid, Electric Vehicle (EV) and Plug-in Hybrid Electric Vehicles (PHEV).

7 Battery A2 2. Traction Motor A2 2. Activities Conditions Incentives Division General List of Activities Eligible for Investment Promotion Air-condition A2 2. system Battery 2. A2. Management Systems (BMS). A2 2. Drive Control Units (DCU). A2 2. On-Board Charger EV Connector 2. A2. with plug and socket A2 2. DC/DC. Converter A2 2. Inverter Portable Electric Vehicle Charger A2 2. Electrical Circuit Breaker A2 2. EV Smart A2 2. Charging System Development A2 2. Front/rear axle for battery electric bus A2 2. Manufacture of rubber tire for vehicle Manufacture of Fuel System Parts including Projects must have part forming process and assembling process as A3 2.

8 Fuel Pump approved by the Board. A3 2. Injection Pump A3 2. Injector A4 2. Fuel Pipe/Tube Manufacture of Transmission System Parts including 2. A3. Sun Gear A3 2. Ring Gear Shift Gear A3 2. Activities Conditions Incentives Division General List of Activities Eligible for Investment Promotion Projects must have part forming process A3 2. Transfer Case and assembling process as approved by the Board. A3 2. Torque Converter Projects must have part forming process and assembling process as approved by the Board. Projects must have part forming process A3 2. Carrier and assembling process as approved by the Board.

9 Propeller Shaft Projects must have part forming process A3 2. and assembling process as approved by the Board. Driver Shaft A3 2. Projects must have part forming process and assembling process as approved by the Board. Universal Join Projects must have part forming process A3 2. and assembling process as approved by the Board. Differential A3 2. Projects must have part forming process and assembling process as approved by the Board. A3 2. Transmission Case Manufacture of Engine System Parts including A3 2. Turbocharger Projects must have part forming process and assembling process as approved by the Board.

10 Turbocharger A4 2. Parts including Turbine Blade, Turbine Housing and Bearing Housing A4 2. Cylinder Head A4 2. Cylinder Block Crankshaft A4 2. Camshaft A4 2. Connecting Rod 2. A4. Activities Conditions Incentives Division General List of Activities Eligible for Investment Promotion Valve A4 2. Piston A4 2. Gear A4 2. Starting Motor or Parts A4 2. Alternator or parts A4 2. Rocker Arm A4 2. Waste Gate A4 2. Actuator Manufacture of Safety Parts including Air Bag/Safety A4 2. Belt Air Bag Inflator, A3 2. Gas Generator, Gas Generant Parts for Air Bag, 2. A4. Initiator and Coolant Filter Parts for Safety A4 2.