SMCJ Series e3 - littelfuse.com

1 Transient Voltage Suppression Diodes 2015 littelfuse , are subject to change without notice. Revised: 11/20/15 Surface Mount 1500W > SMCJ seriesTVS devices are ideal for the protection of I/O Interfaces, VCC bus and other vulnerable circuits used in Telecom, Computer, Industrial and Consumer electronic SMCJ Series is designed specifically to protect sensitive electronic equipment from voltage transients induced by lightning and other transient voltage Pulse Power Dissipation at TA=25 C by 10/1000 s Waveform ( )(Note 1), (Note 2), (Note 5)PPPM1500 WPower Dissipation on Infinite Heat Sink at TL= Forward Surge Current, Single Half Sine Wave (Note 3)IFSM200 AMaximum Instantaneous Forward Voltage at 100A for Unidirectional Only (Note 4)

2 Temperature RangeTJ-65 to 150 CStorage Temperature RangeTSTG-65 to 175 CTypical Thermal Resistance Junction to LeadR JL15 C/WTypical Thermal Resistance Junction to AmbientR JA75 C/WNotes:1. Non-repetitive current pulse , per Fig. 4 and derated above TJ (initial) =25OC per Fig. Mounted on copper pad area of ( x ) to each Measured on single half sine wave or equivalent square wave for unidirectional device only, duty cycle=4 per minute VF < for single die parts and VF< for stacked-die The PPPM of stacked-die parts is 2000W and please contact littelfuse for the detail stacked-die Ratings and Thermal Characteristics (TA=25OC unless otherwise noted)Agency ApprovalsAGENCYAGENCY FILE NUMBERE230531 1500W peak pulse power capability at 10/1000 s waveform, repetition rate (duty cycles)

3 Excellent clamping capability Low incremental surge resistance Typical IR less than 1 A when VBR min>12V For surface mounted applications to optimize board space Low profile package Built-in strain relief Typical failure mode is short from over-specified voltage or current Whisker test is conducted based on JEDEC JESD201A per its table 4a and 4c IEC-61000-4-2 ESD 30kV(Air), 30kV (Contact) ESD protection of data lines in accordance with IEC 61000-4-2 EFT protection of data lines in accordance with IEC 61000-4-4 Fast response time: typically less than from 0V to BV min Glass passivated chip junction High temperature to reflow soldering guaranteed: 260 C/40sec VBR @ TJ= VBR@25 C x (1+ T x (TJ - 25))( T:Temperature Coefficient, typical value is ) Plastic package is flammability rated V-0 per Underwriters Laboratories Meet MSL level1, per J-STD-020, LF maximun peak of 260 C Matte tin lead free plated Halogen free and RoHS compliant Pb-free E3 means 2nd level interconnect is Pb-free and the terminal finish material is tin(Sn) (IPC/JEDEC )SMCJ SeriesUni-directionalBi-directionalFunct ional DiagramBi-directional Uni-directional Cathode AnodeRoHSPbe3 DatasheetAdditional InfomarionResourcesSamplesTransient Voltage Suppression Diodes 2015 littelfuse , are subject to change without notice.

4 Revised: 11/20/15 Surface Mount 1500W > SMCJ seriesElectrical Characteristics (TA=25 C unless otherwise noted)Part Number (Uni)Part Number (Bi)MarkingReverseStand offVoltage VR(Volts)Breakdown Voltage VBR (Volts) @ ITTest CurrentIT (mA)Maximum Clamping Voltage VC @ Ipp(V)Maximum Peak Pulse Current Ipp (A)Maximum Reverse Leakage IR @ VR( A)Agency 0 7. 7. 7. 0 0 parts without A , the VBR is 10% and VC is 5% higher than with A partsFor bidirectional type having VR of 10 volts and less, the IR limit is Voltage Suppression Diodes 2015 littelfuse , are subject to change without notice. Revised: 11/20/15 Surface Mount 1500W > SMCJ seriesI-V Curve CharacteristicsVoltage TransientsTimeVoltage Across TVSC urrent Through TVSV oltage or CurrentFigure 1 - TVS Transients Clamping WaveformRatings and Characteristic Curves (TA=25 C unless otherwise noted)td-Pulse Width (ms)PPPM-Peak Pulse Power (kW)

5 , 2kW at 10x1000 s, 25 CTJ initial = TambSingle die, at 10x1000 s, 25 CFigure 2 - Peak Pulse Power RatingVcVBRVRIRITIppVUni-directionalVFVc VBRVRIRITIppVVcVBRVRIppIRITBi-directiona lPPPM Peak Pulse Power Dissipation -- Max power dissipation VR Stand-off Voltage -- Maximum voltage that can be applied to the TVS without operationVBR Breakdown Voltage -- Maximum voltage that flows though the TVS at a specified test current (IT)VC Clamping Voltage -- Peak voltage measured across the TVS at a specified Ippm (peak impulse current)IR Reverse Leakage Current -- Current measured at VRVF Forward Voltage Drop for Uni-directional continues on next Voltage Suppression Diodes 2015 littelfuse , are subject to change without notice.

6 Revised: 11/20/15 Surface Mount 1500W > SMCJ seriesIPPM- Peak Pulse Current, % IRSM005010 01501. secPeak ValueIPPMIPPM2TJ=25 CPulse Width(td) is definedas the point where the peak current decays to 50% of IPPM10/1000 sec. Waveformas defined by (ms)Half ValueIPPM( )1101001000100001000001101001000 Uni-directional V=0V Bi-directional V=0 VBi-directional V=VRUni-directional V=VR Cj(pF)VBR-Reverse Breakdown Voltage(V)Figure 4 - Pulse WaveformFigure 5 - Typical Junction Capacitance02040608010012014016018020011 0100 Number of Cycles at 60 HzIFSM - Peak Forward Surge Current (A)Figure 7 - Maximum Non-Repetitive Peak Forward Surge Current Uni-Directional OnlyFigure 3 - Peak Pulse Power Derating CurveRatings and Characteristic Curves (TA=25 C unless otherwise noted) (Continued)0204060801000255075100125175 Peak Pulse Power (PPP) or Current (IPP)Derating in Percentage %150TJ - Initial Junction Temperature ( C) Thermal Impedance ( C/W)

7 T -Pulse Duration (s)PFigure 6 - Typical Transient Thermal ImpedanceIF-Peak Forward Current(A)VF-Peak Forward Voltage(V) dieFigure 8 - Peak Forward Voltage Drop vs Peak Forward Current (Typical Values)Transient Voltage Suppression Diodes 2015 littelfuse , are subject to change without notice. Revised: 11/20/15 Surface Mount 1500W > SMCJ seriesPhysical ounce, gramsCaseJEDEC DO214AB. Molded plastic body over glass passivated junctionPolarityColor band denotes positive end (cathode) except Tin-plated leads, Solderable per JESD22-B102 DimensionsSoldering ParametersTemperature (T)Time (t)Ts(min)Ts(max)TLTPtsPreheattLtpRamp-u pCritical ZoneTL to TPRamp-downt 25 C to Peak25 CReflow ConditionLead free assemblyPre Heat- Temperature Min (Ts(min))150 C - Temperature Max (Ts(max))200 C- Time (min to max) (ts)60 180 secsAverage ramp up rate (Liquidus Temp (TA) to peak3 C/second maxTS(max) to TA - Ramp-up Rate3 C/second maxReflow- Temperature (TA) (Liquidus)217 C - Time (min to max) (ts)60 150 secondsPeak Temperature (TP)260+0/-5 CTime within 5 C of actual peak Temperature (tp))

8 20 40 secondsRamp-down Rate6 C/second maxTime 25 C to peak Temperature (TP)8 minutes not exceed260 1 1 SpecificationsHigh Temp. StorageJESD22-A103 HTRBJESD22-A108 Temperature CyclingJESD22-A104 MSLJEDEC-J-STD-020, Level 1H3 TRBJESD22-A101 RSHJESD22-A111(all dimensions in mm)ILKJS older PadsDO-214AB (SMC J-Bend)BFGHECDAC athode Band(for Uni-directional products only)Transient Voltage Suppression Diodes 2015 littelfuse , are subject to change without notice. Revised: 11/20/15 Surface Mount 1500W > SMCJ seriesPart Numbering SystemPackagingPart numberComponent Package QuantityPackagingOptionPackaging SpecificationSMCJxxxXXDO-214AB3000 Tape & Reel - 16mm tape/13 reelEIA STD RS-481 Part Marking SystemVR VOLTAGEBI-DIRECTIONAL5% VBR VOLTAGE TOLERANCESERIESSMCJXXXCAFXXXYMXXXM arking CodeTrace Code Marking Y:Year Code M: Month Code XXX: Lot CodeLittelfuse LogoCathode Band(for Uni-directional products only)Tape and Reel Specification ( ) ( ) ( ) ( ) ( ) Arbor Hole (330) Dimensions are in inches(and millimeters).

9 Direction of DIA( )Cover tapeCatho