Example: marketing
SP339E DS - maxlinear.com
SP339E 3 REV. 1.0.6 RS-232/RS-485/RS-422 TRANSCEIVER WITH INTERNAL TERMINATION PIN DESCRIPTIONS BY MODE (MODE1, MODE0) Pin Name 00, Figure1 01, Figure2 10, Figure3 11, Figure4 1 L1 R1 Output 1 1 2 L2 R2 Output R1 Output R1 Output
Information
Domain:
Source:
Link to this page:
Documents from same domain
SP3222E / SP3232E Data Sheet - maxlinear.com
www.maxlinear.comTrue 3.0V to 5.5V RS-232 Transceivers SPE SPE REV 1.0.2 1/22 FEATURES Meets true EIA/TIA-232-F standards from a 3.0V to 5.5V power supply Minimum 120kbps data rate under full load 1μA low power shutdown with receivers active (SP3222E) Interoperable with RS-232 down to a 2.7V power source
SP3222E / SP3232E Datasheet - MaxLinear
www.maxlinear.comThe SP3222E and SP3232E series are RS-232 transceiver solutions intended for portable or hand-held applications such as notebook or palmtop computers. The SP3222E / SP3232E series has a high-efficiency, charge-pump power supply that requires only 0.1µF capacitors in 3.3V operation. This charge pump allows the SP3222E
8201, 8202, 8203, 8204 - maxlinear.com
www.maxlinear.com8201, 8202, 8203, 8204 Acceleration Processor Data Sheet, DS-0157-05 Page 3 Exar Confidential compliance with particular requirements of Buyer or Buyer's customer ...
XR33052/XR33053/XR33055/XR33058 Data Sheet
www.maxlinear.com±60V Fault Tolerant 3.0V to 5.5V RS-485/RS-422 Transceivers R 33052R 33053R 33055R 33058 REV2C 1/20 Description The XR33052, XR33053, XR33055, and XR33058 (XR3305x) are a family of high performance RS-485/RS-422 devices designed for
Related documents
±15kV ESD-Protected, Slew-Rate-Limited, Low-Power, RS …
datasheets.maximintegrated.comdesigned for full-duplex communications, while the MAX481E, MAX483E, MAX485E, MAX487E, and MAX1487E are designed for half-duplex applications. For applications that are not ESD sensitive see the pin-and function-compatible MAX481, MAX483, MAX485, MAX487–MAX491, and MAX1487. Applications Low-Power RS-485 Transceivers Low-Power RS-422 Transceivers
MAX481/MAX483/MAX485/ MAX487–MAX491/MAX1487 …
datasheets.maximintegrated.comMAX1487 transceivers on the bus. Full-duplex communi-cations are obtained using the MAX488–MAX491, while the MAX481, MAX483, MAX485, MAX487, and MAX1487 are designed for half-duplex applications. _____Applications Low-Power RS-485 Transceivers Low-Power RS-422 Transceivers Level Translators Transceivers for EMI-Sensitive Applications
MAX13487E/MAX13488E Half-Duplex RS-485-/RS-422- …
datasheets.maximintegrated.comMAX13487E/MAX13488E Half-Duplex RS-485-/RS-422-Compatible Transceiver with AutoDirection Control www.maximintegrated.com Maxim Integrated | 3 Electrical Characteristics (continued) (VCC = +5V ±5%, TA = TMIN to TMAX, unless otherwise noted. Typical values are at VCC = +5V and TA = +25°C.) (Note 1) PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS ...
PL-2303HX Edition (Chip Rev D) USB to Serial Bridge ...
www.prolific.com.two One, one and a half, or two stop bits o Parity error, frame error, and serial break detection o Programmable baud rate from 75 bps to 12M bps o External RS232 driver power down control o Independent power source for serial interface Supports RS-422/RS-485 like serial interface (TXD, DTR_N, and RTS_N pins should be
RS-485 Reference Guide (Rev. A) - TI.com
www.ti.comRS-485 uide 44 Texas Instruments 2014 RS-485 Reference Guide Selection Table Device TX/ RX Duplex Supply (V) Features Signaling Rate (Mbps) HBM ESD (kV) Receiver Fail-Safe Nodes Package(s)
IEEE P802.3ae MDC/MDIO
www.ieee802.orgCopenhagen, Denmark Sept 17-19, 2001 May 4, 2000IEEE P802.3ae MDC/MDIO Slide – V1.03 IEEE 802.3ah Task Force Slide 3 What is MDIO for ? ‘..a simple, two -wire, serial interface to connect a management entity and a