SP3222E / SP3232E Datasheet - MaxLinear

SP3222E / SP3232E Data Sheet - maxlinear.com

True 3.0V to 5.5V RS-232 Transceivers SPE SPE REV 1.0.2 1/22 FEATURES Meets true EIA/TIA-232-F standards from a 3.0V to 5.5V power supply Minimum 120kbps data rate under full load 1μA low power shutdown with receivers active (SP3222E) Interoperable with RS-232 down to a 2.7V power source

  Transceiver, 232 transceivers

SP339E DS - maxlinear.com

SP339E 3 REV. 1.0.6 RS-232/RS-485/RS-422 TRANSCEIVER WITH INTERNAL TERMINATION PIN DESCRIPTIONS BY MODE (MODE1, MODE0) Pin Name 00, Figure1 01, Figure2 10, Figure3 11, Figure4 1 L1 R1 Output 1 1 2 L2 R2 Output R1 Output R1 Output

XR33052/XR33053/XR33055/XR33058 Data Sheet

±60V Fault Tolerant 3.0V to 5.5V RS-485/RS-422 Transceivers R 33052R 33053R 33055R 33058 REV2C 1/20 Description The XR33052, XR33053, XR33055, and XR33058 (XR3305x) are a family of high performance RS-485/RS-422 devices designed for

  Fault, Transceiver

8201, 8202, 8203, 8204 - maxlinear.com

8201, 8202, 8203, 8204 Acceleration Processor Data Sheet, DS-0157-05 Page 3 Exar Confidential compliance with particular requirements of Buyer or Buyer's customer ...

  2018

EX2300 Switch Hardware Guide - Juniper Networks

Sep 02, 2021 · Remove a Transceiver. 225. Remove a QSFP28 Transceiver. 227. Install a Transceiver. 229. Install a QSFP28 Transceiver. 232. Maintain Fiber-Optic Cables. 234. Connect a Fiber-Optic Cable. 234. Disconnect a Fiber-Optic Cable. 235. How to Handle Fiber-Optic Cables. 236. Troubleshooting Hardware. Troubleshooting EX2300 Components. 239

  Network, Transceiver, Juniper, Juniper networks

MAX3160/MAX3161/MAX3162 +3.0V to+5.5V, 1µA, RS-232/ …

as a 2TX/2RX RS-232 interface or a single RS-485/422 transceiver. The MAX3162 is configured as a 2TX/2RX RS-232 interface and a single RS-485/422 transceiver simultaneously. All devices incorporate a proprietary low-dropout trans-mitter output stage and an on-board dual charge pump to allow RS-232 and RS-485/422 compliant perfor-

  Transceiver

© Copyright 2015 2021 Xilinx

6. The GTY transceiver line rate in the F1924 footprint is package limited to 16.3Gb/s. Refer to data sheet for details. 7. These 52.5x52.5mm packages have the same PCB ball footprint as the 47.5x47.5mm packages and are footprint compatible. 8. GTYs in quads 224-230 and 232 are limited to 16Gb/s. Page 4 XMP103 (v2.0)

  Xilinx, Transceiver

CP2102/9

232 designs to USB using a minimum of components and PCB space. The CP2102/9 includes a USB 2.0 full-speed function controller, USB transceiver, oscillator, EEPROM or EPROM, and asynchronous serial data bus (UART) with full modem control signals in a compact 5 x 5 mm QFN-28 package. No other external USB components are required.

  Transceiver

USBXpress™ Family 1.2 Specification) - Silicon Labs

updating RS-232 designs to USB using a minimum of components and PCB space. CP2102N includes a USB 2.0 full-speed function controller, USB transceiver, oscillator, and Universal Asynchronous Receiver/Transmitter (UART) in packages as small as 3 mm x 3 mm. No other external USB components are required for development. All cus-

  Transceiver

Dell EMC PowerSwitch S4100–ON Series Installation Guide ...

transceiver ports. Avoid exposure to laser radiation. Do not stare into open apertures. NOTE: Read this guide before unpacking the switch. For more information, see Unpack the switch. Topics: • Related documents • Information symbols. Related documents. For more information about the S4100-ON Series, see the following documents:

  Transceiver