Standard Test Methods for Downhole Seismic Testing1
explosives, hammers, or air guns, are all acceptable P-wave generators. To produce an identifiable S wave, the source ... significantly different properties may impact the test results. Larger horizontal offsets of 4 to 6 m (12 to 20 ft) for the 2 For referenced ASTM standards, visit the ASTM website, ...
Tags:
Tests, Standards, Seismic, Methods, Impact, Hammer, Downhole, Standard test methods for downhole seismic testing1, Testing1
Information
Domain:
Source:
Link to this page:
Please notify us if you found a problem with this document:
Documents from same domain
Chapter 11 SEISMIC DESIGN CRITERIA - Civil …
www.ce.memphis.eduP1: JsY ASCE003-11.tex ASCE003/SIE-v1.cls September 29, 2005 17:5 Chapter 11 SEISMIC DESIGN CRITERIA 11.1 GENERAL 11.1.1 Purpose. Chapter 11 presents criteria for the design and
Design, Seismic, Chapter, Criteria, Chapter 11 seismic design criteria
Chapter 6. Compression Reinforcement - Flexural …
www.ce.memphis.eduCIVL 4135 118 Compression Reinforcement Chapter 6. Compression Reinforcement - Flexural Members Ifabeamcrosssectionislimitedbecauseofarchitecturalorotherconsiderations,itmayhap-
Chapter, Members, Chapter 6, Compression reinforcement flexural, Compression, Reinforcement, Flexural, Compression reinforcement flexural members
Review of Engineering Fundamentals - University …
www.ce.memphis.eduReview of Engineering Fundamentals CIVL 4197. Course Format ... FE Chemical 853 77% FE Civil 4,874 70% FE Electrical & Computer 1,217 …
Chemical, Engineering, Review, Fundamentals, Review of engineering fundamentals
ASCE Requirements for Citations f13 - Civil …
www.ce.memphis.eduASCE Requirements for Citations Books Feld, J. and Carper, K. (1997). Construction Failure, 2nd Ed., Wiley, New York. Book references must include author, book title, publisher, and the publisher’s
Requirements, Case, Citation, Asce requirements for citations f13, Asce requirements for citations
2 - Aggregate Gradation and Sampling - Civil …
www.ce.memphis.eduCIVL 3137 3 Gradation Analysis percent coarser or percent retained percent finer or percent passing
Analysis, Sampling, Aggregate, Aggregate gradation, Gradation
BEAM DESIGN - University of Memphis
www.ce.memphis.edu6 2. SHEAR DESIGN IN FLAT PLATES AND FLAT SLABS When two-way slabs are supported directly by columns, as in flat slabs and flat plates, or when slabs carry concentrated loads, as in footings, shear near the columns is of critical
Topic 14 - Foundation Design - Civil Engineering
www.ce.memphis.eduInstructional Materials Complementing FEMA 451, Design Examples Foundation Design 14-7 Reinforced Concrete Footings: Basic Design Criteria (concentrically loaded) d/2 …
Curing Concrete, Chapter 12 - The University of …
www.ce.memphis.edu221 Chapter 12 Curing Concrete 3. Methods that accelerate strength gain by supplying heat and additional moisture to the concrete. This is usually accomplished with live steam, heating coils,
Chapter, Concrete, Chapter 12, Curing, Curing concrete, Chapter 12 curing concrete
AAA CE4135 ver2 - Civil Engineering
www.ce.memphis.eduCIVL 4135 Chapter 1. Introduction • 2 A problem unique to the design of reinforced concrete structures is the need to detail each member throughout.
Aggregates for Concrete - Department of Civil …
www.ce.memphis.eduT 27). The range of particle sizes in aggregate is illustrated in Fig. 5-4. The aggregate particle size is determined by using wire-mesh sieves with square openings.
Related documents
GARAGE/SHOP SAFETY CHECKLIST
www.keeptruckingsafe.orgImpact tools, hammers kept free of splinters/mushrooms? Extension + straight ladders extend 3’ beyond landing? Hoists inspected monthly and documented? Stepladder or commercial stepstool used for high access? Hoists inspected annually by outside service?
‘Struck-By’ Hazards
www.osha.govjack hammers, pavement saws 6. Working with powder-actuated tools 7. Pushing or pulling objects that may become airborne ... or use impact tools with mushroomed heads; the head could fl y off, striking you or others. Operators of powder-actuated tools (gunpowder) must be trained and licensed. Train all workers on safe operation of tools, and ...
Hand and Power Tool Safety - Wisconsin Department of ...
doa.wi.govHammers and Striking Tools – (Ex. Nail, soft-faced, ball-peen, chipping, sledge, setting, etc.) Use the correct hammer head, weight and size tailored to its designed purpose. Strike the surfaces squarely, avoid hitting at an angle because doing so could result in sparks occurring.
Safety, Power, Tool, Hands, Hammer, Hand and power tool safety
Metallurgical Aspects of HIGH- CHROMIUM WHITE IRONS
www.foundry-planet.comii) When conditions of repeated impact are anticipated, the lower-carbon alloys, class I type B (Ni-Hard 2), are recommended because they have lesscarbideand,therefore,greatertoughness. iii) A special grade, class I type C, has been developed for producing grindingballsandslugs.Herethenickel-chromiumalloycompositionhas
High, Aspects, Impact, Metallurgical, Chromium, Metallurgical aspects of high chromium
5 NOISE SOURCES - WHO
www.who.intimpact induced resonant free vibration of a surface. 5.2.2. Fluid Noise Air turbulence and vortices generate noise, especially at high air flow velocities. Turbulence can be generated by a moving or rotating solid object, such as the blade tip of a ventilator fan, by