Technical Data Sheet

1 ^(ValidationDate)7207201,2silicone acrylicTechnical Data SheetSolvalittProduct descriptionThis is a one component physically drying silicone acrylic coating . It is heat resistant up to 600 C. Can be used as primer, mid coat or finish coat in atmospheric environments. Suitable for properly prepared carbon steel,galvanised steel, stainless steel and aluminium to colour to variations in the thermal stability of pigments, slight colour changes can occur when the coating is heated. Note that such a colour change will not affect the performance of the useOther variants availableSolvalitt AluProtective:Designed as a heat resistant coating .

2 Suitable for insulated and non insulated surfaces. Recommended as finish coat for insulated surfaces, in systems with suitable to separate TDS for each dataPropertyTest/StandardDescriptionSoli ds by volumeGloss level (GU 60 )ISO 2813 VOC-US/Hong KongUS EPA method 24 (tested)(CARB(SCM)2007, SCAQMD rule 1113, Hong Kong)VOC-EUIED (2010/75/EU) (theoretical)43 Flash pointISO 3679 Method 126 Cmatt (0-35)520 g/l483 3233 VOC-ChinaGB/T 23985-2009 (tested)473 g/lVOC-KoreaKorea Clean Air Conservation Act (tested)(Max.)

3 Thinning ratio included)492 g/l 2 %The provided data is typical for factory produced products, subject to slight variation depending on description: According to Jotun Performance Coatings' : Heat resistant topcoats can be tinted in a range of colours. However, due to its pigmentation certain colours will appear less gloss and colour stable than of issue:16 July 2021 Page: 1/5 This Technical Data Sheet supersedes those previously Technical Data Sheet (TDS) is recommended to be read in conjunction with the Safety Data Sheet (SDS) and the Application Guide (AG) for this product.

4 For your nearest local Jotun office, please visit our website at Data SheetSolvalittFilm thickness per coatDry film thicknessWet film thicknessTheoretical spreading rateTypical recommended specification range205021307014 m mm /l---Surface preparation summary tableSubstrateMinimumRecommendedSa 2 (ISO 8501-1)Carbon steelSa 2 (ISO 8501-1)Stainless steelThe surface shall be sweep blast-cleaned with the nozzle angle at 45-60 from perpendicular at reduced nozzle pressure to create a sharp and angular surface profile using approved nonmetallic abrasive surface shall be sweep blast-cleaned with the nozzle angle at 45-60 from perpendicular at reduced nozzle pressure to create a sharp and angular surface profile using approved nonmetallic abrasive surface shall be hand or machine abraded with non-metallic abrasives or bonded fibre

5 Machine or hand abrasive pads to impart a scratch pattern to the abrasive blast cleaning to sspc -SP 13/NACE No. steelThe surface shall be clean, dry and appear with a rough and dull blast-cleaning using non-metallic abrasive leaving a clean,rough and even surfacesClean, dry and undamaged compatible coatingClean, dry and undamaged compatible coatingSurface preparationApplication methodsThe product can be applied bySpray:Use air spray or airless :Recommended for stripe coating and small areas. Care must be taken to achieve the specified dry film :May be used for small areas.

6 Not recommended for first primer coat. Care must be taken to achieve the specified dry film preparationTo secure lasting adhesion to the subsequent product all surfaces shall be clean, dry and free from any of issue:16 July 2021 Page: 2/5 This Technical Data Sheet supersedes those previously Technical Data Sheet (TDS) is recommended to be read in conjunction with the Safety Data Sheet (SDS) and the Application Guide (AG) for this product. For your nearest local Jotun office, please visit our website at Data SheetSolvalittSingle packProduct mixingThinner/Cleaning solventThinner:Jotun Thinner No.

7 7 Jotun Thinner No. 10/Nozzle tip (inch/1000):Pressure at nozzle (minimum):Guiding data for airless spray15-17100 bar/1450 psiDrying and Curing timeSurface (touch) dryWalk-on-dry1 h45 min30 min15 min4 h3 h2 hSubstrate temperature10 C23 C40 C5 CDry to over coat, minimum8 h5 h4 h3 hWalk-on-dry: Minimum time before the coating can tolerate normal foot traffic without permanent marks,imprints or other physical and curing times are determined under controlled temperatures and relative humidity below 85 %, and at average of the DFT range for the applied Solvalitt film may have slightly reduced mechanical properties.

8 This effect can however be overcome by heating the paint system to 200 C for approx. 1 to over coat, minimum: The recommended shortest time before the next coat can be (touch) dry: The state of drying when slight pressure with a finger does not leave an imprint or reveal maximum overcoating intervals, refer to the Application Guide (AG) for this , atmosphericHeat resistance C600 ContinuousPeak-Date of issue:16 July 2021 Page: 3/5 This Technical Data Sheet supersedes those previously Technical Data Sheet (TDS) is recommended to be read in conjunction with the Safety Data Sheet (SDS) and the Application Guide (AG) for this product.

9 For your nearest local Jotun office, please visit our website at Data SheetSolvalittProduct compatibilityPrevious coat:Subsequent coat:epoxy, zinc silicate, silicone acrylic, multipolymeric matrixsilicone acrylicPackaging (typical)The volume stated is for factory made colours. Note that local variants in pack size and filled volumes can vary due to local of containers(litres)Solvalitt55 Storage The product must be stored in accordance with national regulations. Keep the containers in a dry, cool, well ventilated space and away from sources of heat and ignition.

10 Containers must be kept tightly closed. Handle with life at 23 C24 Solvalittmonth(s)In some markets commercial shelf life can be dictated shorter by local legislation. The above is minimum shelf life, thereafter the paint quality is subject to (litres)Depending on the actual exposure of the coating system, various primers and topcoats can be used in combination with this product. Some examples are shown below. Contact Jotun for specific system product is for professional use only. The applicators and operators shall be trained, experienced and have the capability and equipment to mix/stir and apply the coatings correctly and according to Jotun's Technical documentation.