Example: stock market
TECHNICAL DATA SHEET - Henry
Air Permeance - Material @1.57psf (75Pa) 0.0001 cfm/ft² (0.0005 L/[sec-m²]) ASTM E2178 Air Leakage - Assembly Pass ASTM E2357 Elongation 250% ASTM D412 Tensile Strength 140 psi (965 kPa) ASTM D412 Flame Spread Index 10, Class A ASTM E84 Smoke Developed 15, Class A ASTM E84 Fire Testing Complies with NFPA 285 in various wall
Tags:
Information
Domain:
Source:
Link to this page:
Documents from same domain
TECHNICAL DATA SHEET - Henry
henry.comImpermeable to air, moisture vapor and water Compatible with Henry® Air-Bloc fluid applied air barriers Self-gasketing when penetrated and under compression with self-tapping screws Usage Blueskin SA is designed for use as a self-adhered air, vapor and water resistive barrier. It can also be used as a transition sheet
TECHNICAL DATA SHEET
henry.comREVISION: 11/17/15 Henry Company, 999 N. Sepulveda Blvd., Ste. 800, El Segundo, CA 90245 Technical Services - Phone: (800) 486-1278 – Email: techservices@henry.com www.henry.com Henry CM100 Fast Curing, Elastomeric Fluid Membrane Uses Henry CM100 may be used as a waterproofing and roofing membrane on horizontal or vertical surfaces. Ideal alternative to hot
TECHNICAL DATA SHEET - Henry
henry.comcast-in-place concrete, concrete block, steel, aluminum and galvanized metal. Strike masonry joints full-flush. Concrete surfaces must be smooth and without large voids, spalled areas or sharp protrusions. Concrete must be cured a minimum of 14 days. Curing
TECHNICAL DATA SHEET Blueskin WP200 - Henry
henry.comREVISION: 02/27/17 Henry Company 999 N. Sepulveda, Ste 800, El Segundo CA 90245-2754 Technical Services- Phone (800) 486-1278 – Email: techservices@henry.com www.henry.com Blueskin WP 200 Self-Adhesive Waterproofing Membrane Uses Blueskin WP200 is designed for use as a self-adhered s heet waterproofing membrane in above or below grade applications.
HE784 - AQUA-BLOC® WB - henry.com
henry.comLimited Warranty We, the manufacturer, warrant only that this product is free of defects, since many factors which affect the results obtained from this product - such as weather, workmanship, equipment utilized and prior condition of the substrate - are
Henry Blueskin VP160 Air Barrier System Installation Manual
henry.com3 1. Introduction This installation manual includes materials and installation procedures for Henry® Blueskin® VP160 Self-Adhered Water Resistive Air Barrier system. Blueskin® VP160 meets the current IBC and IECC air barrier requirements for a water resistive barrier (WRB) as referenced in ICC ESR-2975.
Henry 925 BES Sealant
henry.comHenry® 925 BES Sealant is a premium, moisture cure sealant for construction joints subject to dynamic joint movement. This one-part, low odor, moisture cure product provides excellent weathering resistance, flexibility, very low VOC, through use of a silyl-terminated polyether (STPE) polymer. Upon curing, it is paintable with latex based paints.
Air-Bloc All Weather STPE
henry.comHenry® Air-Bloc All-Weather STPE is a low VOC, UV and fire-resistant fluid applied, elastomeric membrane designed to provide a vapor permeable, water resistive air barrier when applied to above-grade wall assemblies. It is single-component, moisture cure
Air & Water Barrier Membrane - Henry
henry.comConcrete . ASTM C836 load suction pressure-Low Temperature Flexibility and Crack Bridging @ –20°C . ASTM C836 -Aging-Long Term Flexibility . CGSB 71 -GP-24M -Nail Sealability . ASTM D1970 --Resistance to Mold, Mildew & Fungal growth . ASTM D5590 . ASTM E84-VOC Content . Gray . 60% . 10.8 lbs/gal (1.3 kg/l) 2 Hours to touch dry . 24 Hours to ...
WATERPROOFING SYSTEMS - Henry
henry.comSecondary Containment Structures • Tunnels • Underground ... Drainage & Irrigation Channels • Potable Water Reserves • Seals Embedded Steel, PVC or HDPE Pipe Penetrations HENRY DRAINAGE COMPOSITES: A BETTER ENGINEERED SOLUTION FOR MANAGING THE FLOW OF WATER ... highway drainage systems.
Related documents
Ventilation for buildings — Calculation methods for the ...
www.cres.grEN 12237, Ventilation for buildings — Duct work — Circular sheet metal air ducts — Strength and leakage — Requirements for testing EN 12792, Ventilation for buildings — Symbols, units and terminology EN 13053, Ventilation for building — Air handling units – Ratings and performance for components and sections
Guideline on Through Penetration Firestopping
www.smacna.orgThe Sheet Metal and Air ... Society Testing Materials (ASTM) E 814 or Underwriters Laboratories, Inc. (UL) Standard 1479] ... air leakage test. It is a measure of the ability of a fire resistive assembly to resist air or smoke infiltration resulting from pressure differences. L …
Fire Separations & Fire resistance Ratings
cwc.caprotection, using firestop systems. More information on firestop systems can be found in the W Fire Fact Sheet entitled “Fire Stops and Fire locks.” Fire-Resistance Ratings For an assembly or a structural member that is required to have a fire-resistance rating, Subsection 3.1.7. of the N specifies that the fire-resistance rating shall be
1756 ControlLogix I/O Specifications - Rockwell Automation
literature.rockwellautomation.comOpen wire Off-state leakage current 1.5 mA min Loss of power Transition range 46…85V AC Time stamp of diagnostics ±1 ms Technical Specifications - 1756-IA8D Attribute 1756-IA8D Inputs Eight diagnostic (4 points/group) Operating voltage range(1) 79…132V AC, 47…63 Hz Input delay time (screw to backplane) Off to On On to Off
DESIGN AND INSTALLATION GUIDE - Gastite
www.gastite.comair ducts within the premises will provide additional safety.” Gastite recommends that all continuous metallic systems be bonded and grounded. The owner should confirm with an electrical or construction specialist that each continuous metallic system in a structure has been bonded and grounded by an electrical professional
MasterProtect H 1000 - Master Builders Solutions
assets.master-builders-solutions.comAir, substrate, and material temperatures should be 20 °F (-7 °C) and rising at the time of the application. Substrate must be frost free. Do not apply sealer when temperatures are expected to fall below 20 °F (-7 °C) within 12 hours or when rain is expected within 4 hours following application. Maximum application temperature is 95 °F (35 ...