Example: marketing
TECHNICAL DATA SHEET - Henry
Mortar joints on CMU walls should be struck full and flush with block surface. Cracks in masonry and concrete up to ½” ... Refer to the Safety Data Sheet prior to using this product. The Safety Data Sheet is available at www.henry.com or by emailing
Tags:
Information
Domain:
Source:
Link to this page:
Documents from same domain
TECHNICAL DATA SHEET - Henry
henry.comcast-in-place concrete, concrete block, steel, aluminum and galvanized metal. Strike masonry joints full-flush. Concrete surfaces must be smooth and without large voids, spalled areas or sharp protrusions. Concrete must be cured a minimum of 14 days. Curing
TECHNICAL DATA SHEET - Henry
henry.comImpermeable to air, moisture vapor and water Compatible with Henry® Air-Bloc fluid applied air barriers Self-gasketing when penetrated and under compression with self-tapping screws Usage Blueskin SA is designed for use as a self-adhered air, vapor and water resistive barrier. It can also be used as a transition sheet
TECHNICAL DATA SHEET
henry.comREVISION: 11/17/15 Henry Company, 999 N. Sepulveda Blvd., Ste. 800, El Segundo, CA 90245 Technical Services - Phone: (800) 486-1278 – Email: techservices@henry.com www.henry.com Henry CM100 Fast Curing, Elastomeric Fluid Membrane Uses Henry CM100 may be used as a waterproofing and roofing membrane on horizontal or vertical surfaces. Ideal alternative to hot
TECHNICAL DATA SHEET Blueskin WP200 - Henry
henry.comREVISION: 02/27/17 Henry Company 999 N. Sepulveda, Ste 800, El Segundo CA 90245-2754 Technical Services- Phone (800) 486-1278 – Email: techservices@henry.com www.henry.com Blueskin WP 200 Self-Adhesive Waterproofing Membrane Uses Blueskin WP200 is designed for use as a self-adhered s heet waterproofing membrane in above or below grade applications.
HE784 - AQUA-BLOC® WB - henry.com
henry.comLimited Warranty We, the manufacturer, warrant only that this product is free of defects, since many factors which affect the results obtained from this product - such as weather, workmanship, equipment utilized and prior condition of the substrate - are
Henry Blueskin VP160 Air Barrier System Installation Manual
henry.com3 1. Introduction This installation manual includes materials and installation procedures for Henry® Blueskin® VP160 Self-Adhered Water Resistive Air Barrier system. Blueskin® VP160 meets the current IBC and IECC air barrier requirements for a water resistive barrier (WRB) as referenced in ICC ESR-2975.
Henry 925 BES Sealant
henry.comHenry® 925 BES Sealant is a premium, moisture cure sealant for construction joints subject to dynamic joint movement. This one-part, low odor, moisture cure product provides excellent weathering resistance, flexibility, very low VOC, through use of a silyl-terminated polyether (STPE) polymer. Upon curing, it is paintable with latex based paints.
Air-Bloc All Weather STPE
henry.comHenry® Air-Bloc All-Weather STPE is a low VOC, UV and fire-resistant fluid applied, elastomeric membrane designed to provide a vapor permeable, water resistive air barrier when applied to above-grade wall assemblies. It is single-component, moisture cure
Air & Water Barrier Membrane - Henry
henry.comConcrete . ASTM C836 load suction pressure-Low Temperature Flexibility and Crack Bridging @ –20°C . ASTM C836 -Aging-Long Term Flexibility . CGSB 71 -GP-24M -Nail Sealability . ASTM D1970 --Resistance to Mold, Mildew & Fungal growth . ASTM D5590 . ASTM E84-VOC Content . Gray . 60% . 10.8 lbs/gal (1.3 kg/l) 2 Hours to touch dry . 24 Hours to ...
WATERPROOFING SYSTEMS - Henry
henry.comSecondary Containment Structures • Tunnels • Underground ... Drainage & Irrigation Channels • Potable Water Reserves • Seals Embedded Steel, PVC or HDPE Pipe Penetrations HENRY DRAINAGE COMPOSITES: A BETTER ENGINEERED SOLUTION FOR MANAGING THE FLOW OF WATER ... highway drainage systems.
Related documents
PRODUCT DATA SHEET: HI-BUILD EPOXOLINE II - SERIES N69
production.tnemec.comCMU Allow mortar to cure for 28 days. Level protrusions and mortar spatter. ... Safety Data Sheet for important health and safety information prior to the use of this product. ... Dense Concrete & Masonry: From 100 to 150 sq ft (9.3 to 13.9 m²) per gallon. CMU: From 75 to 100 sq ft (7.0 to 9.3 m²) per gallon. ...
FOR PROFESSIONAL USE ONLY SPEC DATA SHEET - EaCo …
www.eacochem.comNMD 80 is a buffered acid-based new masonry cleaner designed for cleaning mortar smears off of new masonry structures. NMD 80 can be used on ... Read the Safety Data Sheet for additional safety and health hazard information prior to use. Do not get in eyes, on skin, or on clothing. Do not wear contact lenses when
PRODUCT DATA SHEET SikaTop®-122 Plus
usa.sika.comConcrete, mortar, and masonry products must be clean ... Sheet and Safety Data Sheet which are available at usa.sika.com or by calling SIKA’s Technical Service Department at 1-800-933-7452. Nothing contained in any SIKA literature or materials relieves the user of the
Safety Data Sheet (SDS) – Masonry Cement Mortars
www.specmix.comPage 1 of 10 Safety Data Sheet (SDS) – Masonry Cement Mortars . SECTION I: PRODUCT IDENTIFICATION . SPEC MIX, LLC . 1230 Eagan Industrial Rd. Ste 160
SAFETY DATA SHEET General Purpose Cement - Cement …
www.cementaustralia.com.auSAFETY DATA SHEET General Purpose Cement Section 1: Identification of the Material and Supplier ... General Purpose Cement is used as a binder in concrete, concrete masonry, mortar and grouts. It is also used in the manufacture of fibre cement products, in soil stabilisation in building construction ... Industrial Safety Gloves and Mittens ...
TECHNICAL DATA SHEET - Henry
henry.comSurface Prep: All surfaces to receive Blueskin SA must be clean of oil, dust and excess mortar. Acceptable substrates are exterior-grade gypsum sheathing, plywood, OSB, precast or cast-in-place concrete, concrete block, primed steel, aluminum mill finish, anodized aluminum and galvanized metal. Strike masonry joints flush.
Sure Klean - Prosoco
prosoco.comRead “Preparation” and the Safety Data Sheet before use. ALWAYS TEST a small area (minimum 4-ft x 4-ft) of each surface to confirm suitability and desired results before beginning overall application. Test each type of masonry and each type of stain. Test with the same equipment, recommended surface
A guide to BS EN 998 -1 - Mortar
www.mortar.org.ukMasonry mortar (BS EN 998-2) a The requirements for the properties of fresh masonry mortar are set out in Table 4. The mortar should be sampled in accordance with BS EN 1015-2. b For thin layer mortars the correction time determined in accordance with BS