Example: tourism industry
Technical Data Sheet - Jotun
Technical Data Sheet Solvalitt Alu Film thickness per coat Dry film thickness Wet film thickness Theoretical spreading rate Typical recommended specification range 20 50 20 30 75 13 μm μm m²/l---Surface preparation summary table Substrate Minimum Recommended Carbon steel Sa 2½ (ISO 8501-1) Sa 2½ (ISO 8501-1) Stainless steel The surface ...
Tags:
Information
Domain:
Source:
Link to this page:
Documents from same domain
Technical Data Sheet Jotamastic 87 Aluminium
www.jotun.comPackaging (typical) The volume stated is for factory made colours. Note that local variants in pack size and filled volumes can vary due to local regulations. Size of containers Jotamastic 87 Wintergrade Comp B 4 5 (litres) Jotamastic 87 Standard Comp B 2.7 Jotamastic 87 Aluminium Comp A 14.7 20 3 Volume (litres) Date of issue:27 June 2017 Page ...
Technical Data Sheet Application Guide
www.jotun.comApplication Guide 3140;3240;4320 1,2 3140 Scope The Application Guide offers product details and recommended practices for the use of the product. The Application Guide (AG) must be read in conjunction with the relevant specification, Technical Data Sheet (TDS) and Safety Data Sheet (SDS) for all the products used as part of the coating system.
Technical Data Sheet - Jotun
www.jotun.comPackaging (typical) The volume stated is for factory made colours. Note that local variants in pack size and filled volumes can vary due to local regulations. Size of containers (litres) Aluminium Paint H.R. 5 5 Storage Volume (litres) Depending on the actual exposure of the coating system, various primers and topcoats can be used in
Technical Data Sheet - Jotun
www.jotun.comTechnical Data Sheet Hardtop Flexi The provided data is typical for factory produced products, subject to slight variation depending on colour. Gloss description: According to …
Technical Data Sheet
www.jotun.comTechnical Data Sheet Epoxy HR Surface preparation summary table Substrate Minimum Recommended Carbon steel St 2 (ISO 8501-1) Sa 2½ (ISO 8501-1) Stainless steel The surface shall be hand or machine
Technical Data Sheet - Jotun
www.jotun.comOptimum performance, including adhesion, corrosion protection, heat resistance and chemical resistance is achieved with recommended surface preparation. Date of issue:22 March 2021 Page: 3/7 This Technical Data Sheet supersedes those previously issued.
Technical Data Sheet Application Guide
www.jotun.comEpoxy HR Product description This is a two component polyamine cured phenolic/novolac epoxy coating. It is heat resistant up to 205 °C (401 °F) and can be applied on hot substrates up to 150 °C (302 °F).
Technical Data Sheet
www.jotun.comLEED®v4 (2013) MR credit: Building product disclosure and optimization - Material Ingredients, Option 2: Material Ingredient Optimization, International Alternative Compliance Path - REACH optimization: Fully inventoried chemical ingredients to 100 …
Technical Data Sheet
www.jotun.comThis is a two component amine cured epoxy coating. It is a fast drying, zinc phosphate pigmented, high solids, high build product. Specially designed for new construction where short dry to handle and over coating times are required. Can be used as primer, mid coat, finish coat or as single coat system in atmospheric environments.
SAFETY DATA SHEET - Jotun
www.jotun.com1.3 Details of the supplier of the safety data sheet Product type :Liquid. Product description :Paint. 1.2 Relevant identified uses of the substance or mixture and uses advised against SECTION 1: Identification of the substance/mixture and of the company/ undertaking Product code :3140 1.4 Emergency telephone number SAFETY DATA SHEET
Related documents
NBS - Reference Specification - SE Controls
www.secontrols.comH72 ALUMINIUM STRIP OR SHEET COVERINGS AND FLASHINGS 92 ... Reference specification: Not all clauses in the Reference specification apply to this project. If in doubt about the applicability of a ... Read with A90 General technical requirements. PRODUCTS Aluminium alloy framing sections Standard: To relevant parts of BS EN 515, BS EN 573, BS …
TECHNICAL SPECIFICATION FOR L.T.XLPE POWER CABLE …
dhbvn.org.inTechnical specification of LT single core, two core, three core, 3.5 core and four core,Cross linked Polyethylene (XLPE) insulated,FRLS,, PVC sheathed, armoured power cables. ... stranded aluminium to form compacted and circular shaped conductor having resistance within /
TECHNICAL SPECIFICATION FOR ISOLATORS - OPTCL
www.optcl.co.inTECHNICAL SPECIFICATION FOR ISOLATORS 400KV HCB SINGLE ISOLATOR WITH 1 EARTH SWITCH ... insulators and complete in all respect with bimetallic / aluminium connectors arcing horns operating mechanism, auxiliary switches, indicating devices, fixing detail etc. as described herein after.
DETAILED TECHNICAL SPECS - WATERPROOFING
ipwtwaterproofing.comDETAILED TECHNICAL SPECS - WATERPROOFING CONSTRUCTION SPECIFICATIONS INSTITUTE (CSI) FORMAT 1 PART 1 – GENERAL 1.01 SUMMARY A. Section Includes: Furnishing of all labour, materials, services and equipment necessary for the supply and installation of waterproofing systems (as described in the BOQ) to concrete