TS 102 221 - V11.0.0 - Smart Cards; UICC-Terminal ...

1 ETSI TS 102 221 (2012-06) Smart Cards; UICC-Terminal interface ; physical and logical characteristics (Release 11) Technical Specification ETSI ETSI TS 102 221 (2012-06)2 Release 11 Reference RTS/SCP-T102221vb00 Keywords Smart card ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N 348 623 562 00017 - NAF 742 C Association but non lucratif enregistr e la Sous-Pr fecture de Grasse (06) N 7803/88 Important notice Individual copies of the present document can be downloaded from: The present document may be made available in more than one electronic version or in print. In any case of existing or perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF). In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive within ETSI Secretariat.

2 Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at If you find errors in the present document, please send your comment to one of the following services: Copyright Notification No part may be reproduced except as authorized by written permission. The copyright and the foregoing restriction extend to reproduction in all media. European Telecommunications Standards Institute 2012. All rights reserved. DECTTM, PLUGTESTSTM, UMTSTM and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members. 3 GPPTM and LTE are Trade Marks of ETSI registered for the benefit of its Members and of the 3 GPP Organizational Partners. GSM and the GSM logo are Trade Marks registered and owned by the GSM Association.

3 ETSI ETSI TS 102 221 (2012-06)3 Release 11 Contents Intellectual Property Rights .. 11 Foreword .. 11 Introduction .. 11 1 Scope .. 12 2 References .. 12 Normative references .. 12 Informative references .. 13 3 Definitions, symbols, abbreviations and coding conventions .. 14 Definitions .. 14 Symbols .. 16 Abbreviations .. 16 Coding conventions .. 18 4 physical 18 UICC Form Factors .. 18 ID-1 UICC .. 18 Plug-in UICC .. 19 Mini-UICC .. 19 4FF.

4 20 ID-1 UICC .. 21 Plug-in UICC .. 21 Mini-UICC .. 21 Environmental conditions for card operation and storage .. 21 Specific UICC environmental conditions .. 21 Temperature range for specific UICC environmental 22 High humidity .. 22 Contacts .. 22 Provision of contacts .. 22 Terminal .. 22 UICC .. 22 Contact activation and deactivation .. 22 Contacts assigned by the present document .. 22 Optional contacts .. 23 Inactive contacts .. 23 Contact pressure .. 23 5 Electrical specifications of the UICC - Terminal interface .

5 23 Class A operating conditions .. 24 Supply voltage Vcc (contact C1) .. 24 Reset (RST) (contact C2) .. 24 Programming voltage Vpp (contact C6) .. 24 Clock CLK (contact C3) .. 25 I/O (contact C7) .. 25 Class B operating conditions .. 25 Supply voltage Vcc (contact C1) .. 25 Reset (RST) (contact C2) .. 26 Clock CLK (contact C3) .. 26 I/O (contact C7) .. 26 Class C operating conditions .. 27 Supply voltage Vcc (contact C1) .. 27 Reset (RST) (contact C2) .. 27 Clock CLK (contact C3) .. 28 I/O (contact C7) .. 28 6 Initial communication establishment procedures .. 28 UICC activation and 28 ETSI ETSI TS 102 221 (2012-06)4 Release 11 Supply voltage switching .. 29 Supply voltage classes.

6 29 Power consumption of the UICC during ATR .. 29 Application related electrical parameters .. 30 Answer To Reset content .. 30 Coding of historical bytes .. 31 Speed 31 Global interface bytes .. 31 PPS procedure .. 32 Reset procedures .. 32 Cold reset .. 32 Warm reset .. 32 Reaction to resets .. 33 Clock stop mode .. 33 Bit/character duration and sampling time .. 33 Error handling .. 33 Compatibility .. 34 7 Transmission 34 physical layer .. 35 Data link layer.

7 35 Character frame .. 35 Low impedance I/O line behaviour .. 36 Transmission protocol T = 0 .. 36 Timing and specific options for characters in T = 0 .. 36 Command header .. 36 Command processing .. 37 Procedure bytes .. 37 Status bytes .. 37 Error detection and correction .. 37 Transmission protocol T = 1 .. 38 Timing and specific options for blocks sent with T = 1 .. 38 Information field size .. 38 Character waiting 38 Character waiting time.

8 38 Block waiting time .. 39 Block guard time .. 39 Waiting time extension .. 39 Error detection code .. 39 Block frame structure .. 39 Prologue field .. 40 Epilogue field .. 41 Block notations .. 41 Error free operation .. 42 Error handling for T = 1 .. 42 Protocol initialization .. 43 Block dependent errors .. 43 Chaining .. 43 Rules for 44 Transport layer .. 44 Transportation of an APDU using T = 0 .. 44 Mapping of APDUs to TPDUs .. 44 Case 1.

9 45 Case 2 .. 45 Case 3 .. 46 Case 4 .. 47 Use of procedure bytes '61xx' and '6 Cxx' .. 48 Transportation of a APDU using T = 1 .. 49 Case 1 .. 49 Case 2 .. 49 Case 3 .. 50 Case 4 .. 50 ETSI ETSI TS 102 221 (2012-06)5 Release 11 Application layer .. 50 Exchange of APDUs .. 51 CAT layer .. 51 Proactive command.

10 51 ENVELOPE Commands .. 52 8 Application and file structure .. 53 UICC application structure .. 53 File types .. 53 Dedicated files .. 53 Elementary files .. 54 Transparent EF .. 54 Linear fixed EF .. 54 Cyclic EF .. 54 BER-TLV structure EF .. 55 File referencing .. 55 Methods for selecting a file .. 55 SELECT by File IDentifier referencing .. 56 SELECT by path referencing .. 57 Short File Identifier (SFI) .. 58 Application characteristics .. 58 Explicit application selection .. 58 SELECT by DF name.