USER’S, MAINTENANCE and SERVICE …

1 USER S, MAINTENANCE and SERVICE information MANUAL3 THRU TONSINGLE PACKAGEAIR CONDITIONERGAS/ELECTRIC& ELECTRIC/ELECTRIC66386-YUM-D-0912 CONTENTSSAFETY information .. 2 FOR YOUR SAFETY .. 2 SYSTEM OPERATION.. 2 THERMOSTATS .. 2 INTERMITTENT IGNITION DEVICE .. 2 OPERATING INSTRUCTIONS .. 3 EXPLAIN UNIT FUNCTION .. 4 GENERAL MAINTENANCE .. 4 HEATING SYSTEM INSPECTION .. 4 AIR FILTERS .. 5 BLOWER ASSEMBLY .. 5 MOTORS .. 5 CONDENSER COIL .. 6 REGISTERS .. 6 TROUBLESHOOTING .. 6 BEFORE CALLING A SERVICE TECHNICIAN: .. 6 The manufacturer recommends that the User read all sections of this manual andkeep the manual for future reference.

2 FIRE OR EXPLOSION HAZARDF ailure to follow safety warnings exactly couldresult in serious injury, death, or property Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other WHAT TO DO IF YOU SMELL GAS: Do not try to light any appliance. Do not touch any electrical switch; do not use any phone in your building. Leave the building immediately. Immediately call your gas supplier from a neighbor s phone. Follow the gas supplier s instructions. If you cannot reach your gas supplier, call the fire Installation and SERVICE must be per formed by a qualified installer, SERVICE agency or the gas supplier.

3 66386-YUM-D-09122 Johnson Controls Unitary ProductsSAFETY INFORMATIONFOR YOUR SAFETY Make sure that the furnace area is clear and free of combustible materials, gasoline and other flamma-ble vapors and liquids. Be sure the furnace is clear and free of insulating material. Examine the furnace area after installa-tion of the furnace or the installation of additional insulation. Some types of insulation are combusti-ble. For proper operation of this furnace, air for com-bustion and ventilation is required. Make sure that these openings are not obstructed. For lighting or shutting down this furnace, refer to the lighting instructions provided adjacent to the burners and also located in this manual .

4 A blocked vent roll-out switch is provided in the burner compartment. This switch is a manual reset. If the furnace fails to operate, contact a qualified SERVICE technician. Should the gas supply fail to shut off or if overheat-ing occurs, shut off the gas valve to the furnace before shutting off the electrical supply. Then call a qualified SERVICE technician. Do not use this furnace if any part has been under water. A flood-damaged furnace is extremely dan-gerous. Attempts to use the furnace can result in fire or explosion. A qualified SERVICE technician should be contacted to inspect the furnace and to replace all gas controls, control system parts, elec-trical parts that have been wet or the furnace if deemed necessary.

5 Determine the integrity of the installation regarding the flue gas vent, the return and supply air duct. Confirm the equipment is well supported and there are no signs of deterioration. The manufacturer recommends that main burner, ignition device and controls are inspected by a qualified SERVICE techni-cian before each heating season. SYSTEM OPERATIONTHERMOSTATSSet your thermostat for either heating or cooling then set it forthe desired temperature. DO NOT ADJUST THE THERMO-STAT RAPIDLY ON AND OFF, OR BACK AND FORTHFROM HEAT TO COOL. THIS COULD DAMAGE allow at least 5 minutes between changes.

6 Find thetemperature that is most comfortable to you and then LEAVEYOUR THERMOSTAT ALONE. (Exception is for night orvacation set back to conserve energy).Manually moving the thermostat up or down will not speed uptemperature changes in your rooms. This only causes thethermostat switch to function at your command rather thanresponding to room generated by devices other than the furnace may inter-fere with thermostat performance. Therefore, lamps, radios,television sets, etc. should not be placed near the thermostat. INTERMITTENT IGNITION DEVICE When the thermostat calls for heat, gas is supplied and at thesame time, sparking occurs to light the burner.

7 With theburner lit, the flame sensor rod closes a circuit to the ignitorcontrol which allows the burner to continue to the room thermostat is satisfied, the electrical circuit tothe gas valve is opened, closing main burner gas. If theburner should fail to light, contact your heating contractor orgas utility for SERVICE to insure that proper operating condi-tions are 1- TYPICAL THERMOSTATThis furnace is equipped with an intermittent auto-matic ignition system. Do Not attempt to manuallyrelight the burners. Personal injury could Controls Unitary Products3 INPUTThe correct heat capacity of the furnace is regulated by theburner orifices and the gas pressure.

8 The proper orifices arefurnished but the gas pressure regulator must be adjusted bythe installer or gas utility SERVICE INSTRUCTIONSTO SHUT DOWN THE the main gas shutoff valve(s). off the electric power LIGHT THE not attempt to light the main gas shutoff valve(s).3. Adjust the set point of the room thermostat above the temperature in the on the electric power draft fan will operate. After an adequate purge time, the electric spark igniter will light the burners will extinguish and relight automatically upon the demand of the room SAFETY SYSTEM:This gas furnace is equipped with a manual reset high tem-perature sensor or rollout switch which in the unlikely event ofa sustained main burner flame rollout will shut off the flow ofgas by closing the main gas valve.

9 The ignition modules willalso be disabled, preventing the flow of gas to the valve. Theswitch is located inside the gas heat access panel above theburner inlet. Flame rollout can be caused by blockage of thepower vent system, improper gas pressure or adjustment. Ifthis event occurs the furnace will not operate properly. Thegas supply to the furnace should be shut off and no attemptshould be made to place the furnace in operation. The sys-tem should be inspected by a qualified SERVICE to Figure 2 for a typical SHUT OFF:The ignition modules are designed for 100% shut-off.

10 If thefurnace fails to ignite after three ignition attempts, the flow ofgas will be shut off and the ignition module will lock out. Themodule can be reset by:A. Turning the system switch on the room thermostat to the OFF position and back to the HEAT Decreasing the set point of the room thermostat below the temperature in the conditioned space and returning it to its original Opening and closing the unit's main disconnect switch. If the furnace continues to lock out, a qualified SERVICE techni-cian should be called to determine the cause of the problem.