VIAVI Solutions Data Sheet VIAVI

1 VIAVI SolutionsData SheetVIAVICellAdvisor JD785B Base Station AnalyzerSpectrum analyzer : 9 kHz to 8 GHzCable and Antenna analyzer : 5 MHz to 6 GHzPower Meter: 10 MHz to 8 GHz Specification* ConditionsJD785B specifications apply under these conditions: yThe instrument has been turned on for at least 15 minutes yThe instrument is operating within a valid calibration period yData with no tolerance are considered typical values yCable and antenna measurements apply after calibration to the OSL standard yTypical and nominal values are defined as: Typical: expected performance of the instrument operating at 20 to 30 C after being at this temperature for 15 minutes Nominal: a general, descriptive term or parameterSpectrum analyzer (Standard)FrequencyFrequency range9 kHz to 8 GHz Frequency accuracy (Readout frequency x Internal 10 MHz Frequency reference accuracy + RBW centering + 2 Hz + x Horizontal resolution)Internal 10 MHz Frequency ReferenceAccuracy ppm + aging (0 to 50 C) ppm, after 15 minutes of GPS Lock (0 to 50 C)Aging ppm/yearFrequency SpanRange0 Hz (zero span)10 Hz to 8 GHzResolution1 HzResolution Bandwidth (RBW) 3 dB bandwidth1 Hz to 3 MHz1-3-10 sequenceAccuracy 10% (nominal)Video Bandwidth (VBW) 3 dB bandwidth1 Hz to 3 MHz1-3-10 sequenceAccuracy 10% (nominal)Single Sideband (SSB) Phase NoiseFc 1 GHz, RBW 10 kHz, VBW 1 kHz, RMS detectorCarrier Offset30 kHz100 kHz1 MHz 100 dBc/Hz ( 102 dBc/Hz, typical) 105 dBc/Hz ( 112 dBc/Hz, typical) 115 dBc/Hz ( 120 dBc/Hz, typical)

2 Measurement RangeDANL to +25 dBmInput attenuator range0 to 55 dB, 5 dB stepsMaximum Input LevelAverage continuous power+25 dBmDC voltage 50 V DC2 CellAdvisor JD785B Base Station AnalyzerDisplayed Average Noise Level (DANL)1 Hz RBW, 1 Hz VBW, 50 termination, 0 dB attenuation, RMS detectorPreamplifier Off10 MHz to GHz> GHz to 6 GHz>6 GHz to 7 GHz>7 GHz to 8 GHz 140 dBm ( 145 dBm, typical) 136 dBm ( 140 dBm, typical) 134 dBm ( 138 dBm, typical) 128 dBm ( 134 dBm, typical)Preamplifier On10 MHz to 3 GHz>3 GHz to 5 GHz>5 GHz to 7 GHz>7 GHz to 8 GHz 160 dBm ( 165 dBm, typical) 158 dBm ( 162 dBm, typical) 155 dBm ( 158 dBm, typical) 150 dBm ( 155 dBm, typical)Display RangeLog scale and units (10 divisions displayed)1 to 20 dB/division in 1 dB stepsdBm, dBV, dBmV, dB VLinear scale and units (10 divisions displayed)V, mV, mW, WDetectorsNormal, positive peak, sample, negative peak, RMSN umber of traces6 Trace functionsClear/write, maximum hold, minimum hold, capture, load view on/offTotal Absolute Amplitude AccuracyPreamplifier off, power level > 50 dBm, auto-coupled1 MHz to 8 GHz dB ( dB typical)20 to 30 C after 60-minute warm upAdd dB 10 to 55 C after 60-minute warm upReference LevelSetting range 120 to +100 dBmSetting ResolutionLog scaleLinear scale dB1% of reference levelMarkersMarker typesNormal, delta, delta pair, noise, frequen-cy count markerNumber of markers6 Marker functionsPeak, next peak, peak left, peak right, minimum search marker to center/ start/stopRF Input VSWR1 MHz to 8.

3 1 (typical)Atten >20 dBSecond Harmonic DistortionMixer level 25 dBm50 MHz to GHz< 65 dBc (typical)> GHz to 8 GHz< 70 dBc (typical)Third-Order Inter-Modulation (third-order intercept: TOI)200 MHz to 3 GHz+10 dBm (typical)>3 GHz to 8 GHz+12 dBm (typical)SpuriousInherent residual responseInput terminated, 0 dB attenuation, preamplifier off, RBW at 10 kHz, Sweep mode 90 dBm (nominal)Exceptions 85 dBm at MHz, , , and GHz 80 dBm at GHz 75 dBm at MHz and 428 MHz 70 dBm at MHz and MHzInput-related spurious< 70 dBc (nominal)Dynamic Range2/3 (TOI-DANL) in 1 Hz RBW>104 dBat 2 GHzSweep ms to 1000 s24 s to 200 s Span = 0 Hz (zero span)Accuracy 2%Span = 0 Hz (zero span)ModeContinuous, singleGated SweepTrigger sourceExternal, video, and GPSGate length1 s to 100 msGate delay0 to 100 msTriggerTrigger sourceFree run, video, externalTrigger DelayRange Resolution 0 to 200 s6 sMeasurements*Channel powerOccupied bandwidthSpectrum emission maskAdjacent channel powerSpurious emissionsField strengthAM/FM audio demodulationRoute mapPIM detectionDual spectrum* High-power CW signal generator (Option 003) can be set up CellAdvisor JD785B Base Station AnalyzerCable and Antenna analyzer (Standard)FrequencyRange 5 MHz to 6 GHzResolution10 kHzAccuracy 1 ppmData Points126, 251, 501, 1001, 2001 Measurement ms/point (typical)Measurement AccuracyCorrected directivity 40 dBReflection uncertainty ( + |20log (1+10-EP/20)|) (typical)EP = directivity measured return lossOutput PowerHigh5 MHz to GHz, 0 dBm (typical) GHz to 6 GHz, 5 dBm (typical)

4 Low5 MHz to 6 GHz, 30 dBm (typical) Dynamic RangeReflection 60 dBMaximum Input LevelAverage continuous power +25 dBm (nominal) DC voltage 50 V DCInterference ImmunityOn channel On frequency +17 dBm at > MHz from carrier frequency (nominal) 0 dBm within 10 kHz from carrier frequency (nominal)MeasurementsReflection (VSWR)VSWR range Return loss range Resolution 1 to 65 0 to 60 dB to Fault (DTF)Vertical VSWR range Vertical return loss range Vertical resolution Horizontal range Horizontal resolution 1 to 65 1 to 60 dB 0 to (# of data points 1) x horizontal resolutionMaximum = 1500 m (4921 ft)( x 108) x (VP)/deltaVP = propagation velocityDelta = stop freq start freq (Hz) Cable Loss (1-port)Range Resolution 0 to 30 dB dB1-Port PhaseRange Resolution 180 to +180 Smith ChartResolution Power Meter (Standard)General ParametersDisplay range100 to +100 dBm Offset range0 to 60 dB dB or x W (x = m, u, p)Internal RF Power SensorFrequency range 10 MHz to 8 GHz Span1 kHz to 100 MHzDynamic range 120 to +25 dBmMaximum power+25 dBmAccuracySame as spectrum analyzerExternal RF Power SensorsDirectionalJD731 BJD733 AFrequency range300 MHz to GHz150 MHz to GHzDynamic to 150 W (average)4 to 400 W (peak) to 50 W (average) to 50 W ( peak)Connector typeType-N female on both endsMeasurement typeForward/reverse average power, forward peak power, VSWRA ccuracy (4% of reading + W)1,2 TerminatingJD732 BJD734 BJD736 BFrequency range20 MHz to GHzDynamic range 30 to +20 dBmConnector typeType-N maleMeasurement typeAveragePeakAverage and peakAccuracy 7%1 Optical Power Meter (Standard)

5 Optical Power MeterDisplay range 100 to +100 dBmOffset range0 to 60 dBResolution dB or mWExternal Optical Power SensorsMP-60 AMP-80 AWavelength range780 to 1650 nmMax permitted input level+10 dBm+23 dBmConnector typeType-N female on both endsConnector inputUniversal and mmAccuracy 5%1. CW condition at 25 C 10 C2. Forward power4 CellAdvisor JD785B Base Station Analyzer2-Port Transmission Measurements (Option 001)FrequencyFrequency range 5 MHz to 6 GHz Frequency resolution 10 kHzOutput PowerHigh5 MHz to GHz, 0 dBm (typical) GHz to 6 GHz, 5 dBm (typical)Low5 MHz to 6 GHz, 30 dBm (typical) Measurement SpeedVector ms/point (typical) ms/point (typical)Dynamic Range Vector5 MHz to 3 GHz, 80 dB >3 GHz to 6 GHz, 75 dBat average 5at average 5 Scalar5 MHz to GHz, >110 GHz to 6 GHz, >105 dBMeasurementsInsertion Loss/GainRange Resolution 120 to 100 dB dB2-Port PhaseRange Resolution 180 to +180 Bias-Tee (Option 002)VoltageVoltage range +12 to +32 VVoltage resolution VPower8 W MaxHigh Power CW Signal Generator (Option 003)

6 FrequencyFrequency range 10 MHz to 5500 MHzFrequency reference< 1 ppm maximumFrequency resolution10 kHzOutput PowerRange10 MHz to GHz, 60 to +10 GHz to GHz, 60 to +5 dBmStep1 dBAccuracy dB (20 to 30 C)GPS Receiver and Antenna (Option 010)GPS IndicatorLatitude, longitude, altitudeHigh-Frequency AccuracySpectrum, interference, and signal analyzerGPS lock 10 ppbHold over (for 3 days) 50 ppb (0 to 50 C)15 minutes after satellite lockedConnectorSMA, femaleInterference analyzer (Option 011)MeasurementsSpectrum analyzerSound indicator, AM/FM audio demodulation, interference ID, spectrum recorderSpectrogram Collect up to 72 hours of dataRSSIC ollect up to 72 hours of dataInterference finderSpectrum replayerDual spectrogramChannel Scanner (Option 012)Frequency Range1 MHz to 8 GHzMeasurement Range 110 to +25 dBmMeasurementsChannel scanner 1 to 20 channelsFrequency scanner 1 to 20 frequenciesCustom scanner 1 to 20 channels or frequenciesBluetooth Connectivity (Option 013)Personal area network (PAN)File transfer profile (FTP)Wi-Fi Connectivity (Option 016)Interface typeUSB LAN CardInterface standardIEEE b/g/nChipsetRealTek, RalinkUSB wireless modeInfrastructure modeWeb-based remote control Internet Explorer, Chrome, SafariInternet protocol versionIPv4, IPv65 CellAdvisor JD785B Base Station AnalyzerGSM/GPRS/EDGE Signal analyzer (Options 022 and 042)

7 General ParametersFrequency range 450 MHz to 500 MHz820 MHz to 965 GHz to GHzInput signal range 40 to +25 dBmBurst power dBFrequency error 10 Hz + ref freq accuracy99% confidence levelGMSK modulation qualityPhase RMS AccuracyResidual errorPhase peak accuracy8 PSK modulation quality degrees (typical) degrees(0 < Phase RMS < 8)(0 < Phase peak < 30)EVM AccuracyResidual errorRF power vs. time symbol(2% < EVM < 8%)MeasurementsOption 022 Channel PowerSpectrum Emission MaskPower vs. Time (slot)Frequency errorAuto MeasurePhase error RMSC hannel powerReference powerBurst powerPhase error RMSC hannel powerPhase error peakSpectral densityPeak level at defined rangeMax/min pointPhase error peakOccupied bandwidthEVM RMS*Peak to average powerPower vs. Time (frame)I/Q origin offset*Spectrum emission maskEVM Peak*Occupied BandwidthSpurious EmissionsFrame average powerTSCS purious emission maskI/Q origin offsetOccupied bandwidthPeak frequency at defined rangeBurst power (Slot 0 to 7)BSICB urst powerC/I*Integrated powerTSC (Slot 0 to 7)C/I*PvsT maskOccupied powerPeak level at defined rangeConstellationEVM RMS*Frame average powerBurst powerEVM Peak*Frequency errorModulation typeEVM 95th*Option 042 Channel/Frequency ScannerGroup (traffic, control)Multipath ProfileModulation AnalyzerFrame average powerBurst powerBSIC (NCC, BCC)(10 strongest)Frame avg power trendBSIC, frame no.

8 And timeModulation typeChannels or frequenciesFrame average powerC/I trendC/I, frequency errorAbsolute powerSNR, delayLongitude, latitude, and satellite in all screens* Measurements performed for 8 PSK modulation signals (edge) CellAdvisor JD785B Base Station AnalyzerWCDMA/HSPA+ Signal analyzer (Options 023 and 043)General ParametersFrequency range Band 1 to 14, 19 to 22, 25, 26 Input signal range 40 to +25 dBmRF channel power accuracy dB, dB (typical)Occupied bandwidth accuracy 100 kHzAdjacent channel leakage ratio (ACLR)< 56 dB, dB at 5 MHz offset, < 58 dB, dB at 10 MHz offsetWCDMA modulation QPSKHSPA+ modulationsQPSK, 16 QAM, 64 QAMF requency error 10 Hz + ref freq accuracy99% confidence levelEVM accuracy EVM 20%Residual (typical)Code domain power dB relative power dB absolute powerCode channel power > 25 dBCode channel power > 25 dBCPICH power accuracy dB (typical)

9 MeasurementsOption 023 Channel PowerACLRC onstellationMax, avg active powerCodogramAuto MeasureChannel powerReference powerCPICH powerMax, avg inactive powerCode utilizationChannel powerSpectral densityAbs power at defined rangeRho, EVMS cramble codeRCSIO ccupied bandwidthPeak to average powerPeak CDER elative Code Domain ErrorCPICH, P-CCPCH, S-CCPCH, PICH, P-SCH, S-SCHS pectrum emission maskOccupied BandwidthRel power at defined rangeFrequency errorACLRO ccupied bandwidthTime offsetAbs/Rel code power CDP TableMulti-ACLRI ntegrated powerMulti-ACLRC arrier feed-throughCode error Reference powerSpurious emission maskOccupied powerLowest reference powerScramble codeIndividual code EVM, RCDE, and its constellationCode utilizationFrequency errorSpectrum Emission MaskHighest reference powerCode Domain PowerCode, spreading factorEVM Reference powerAbs power at defined rangeAbs/Rel code powerAllocation (channel type)Peak CDEPeak level at defined rangeIndividual code EVM and its constellationChannel power EVM, modulation typeCarrier feed-throughRel power at defined rangePower bar graph (Abs/Rel/Delta power) CPICH, P-CCPCH, S-CCPCH, PICH,P-SCH, S-SCHR elative, absolute powerCPICH absolute powerChannel powerCPICH relative powerSpurious EmissionsPower bar graph(Abs/Rel/Delta power)CPICH, P-CCPCH, S-CCPCHPICH, P-SCH, S-SCHMax inactive powerPeak frequency at defined rangeScramble codeAvg RCDE QPSK, 16 QAM, 64 QAMP ower Statistics CCDFPeak level at defined rangeOption 043 Channel Scanner (up to 6)Scramble Scanner (up to 6)

10 Multipath ProfileCode Domain PowerMax, avg active powerAmplifier capacityChannel, multipath powerAbs/Rel code powerMax, avg inactive powerPeak amplifier capacityFrequencies or channelsChannel powerEc/Io, delayIndividual code EVMF requency errorAverage amplifier capacityChannel power, scram-ble code, CPICH power, Ec/IoCPICH dominanceChannel powerTime offset, RhoScramble codeScramble codeCarrier feed-throughCode, peak utilizationEc/Io, CPICH power, delayCPICH, P-CCPCH, S-CCPCH, PICH, P-SCH, S-SCH(Composite) EVMA verage utilizationCPICH EVM, P-CCPCH EVMR oute MapCPICH power, Ec/IoLongitude, latitude, and satellite in all screens7 CellAdvisor JD785B Base Station AnalyzercdmaOne/cdma2000 Signal analyzer (Options 020 a)