Wireless

1 2 Wireless 1 Identify existing wiringTwo switches control the lights (3-way installation)2 What you need for a 3-way installation+WARNING! Shock Hazard. May result in serious injury or death. Turn off power at circuit breaker before installing the Turn power off at circuit breaker5 Remove existing switch from wall6 Tag and disconnect wires from the existing switchPlace tag - to identify wire on different color screwDifferent Color ScrewGround(Green / Bare Copper)3-Way Installation - Cas ta Wireless In-Wall Dimmer with Pico Remote ControlLocation 1 Location 2In-wall dimmerPD-6 WCLPico remote control with wall-mounting kitPJ2-WALL- If one switch controls the lights (single-pole installation) See quick-start guide that came with your dimmer- If three or more switches control the lights (multi-location installation) See page 31 for detailsImportant note.

2 3 Choose a location for your Cas ta Wireless dimmerChoose which location you want the Cas ta Wireless dimmer installed in. This will be Location 1 Location 1 Claro Wallplate CW-1+3 Wireless 7 Remove side sections (if necessary)Do not remove outside side sections on dimmers at the end of dimmer has inside side sections in the middle has all side sections Dimmable LED WattageIncandescent/Halogen Total Wattage0 W+600 W500 W400 W1 W 25 W+500 W400 W300 W26 W 50 W+400 W300 W200 W51 W 75 W+300 W200 W100 W76 W 100 W+200 W100 W50 W101 W 125 W+100 W50 W0 W126 W 150 W+0 W0 W0 WABCBBBCBA8 Connect the Cas ta Wireless dimmerTagged WireGround(Green wire )9 Mount the Cas ta Wireless dimmer10 Attach the wallplate snap 11 Remove existing switch from wall at Location 23-Way Installation - Cas ta Wireless In-Wall Dimmer with Pico Remote Control12 Tag and disconnect wires from the switchGround (Green / Bare Copper)Different Color ScrewImportant note:Removing side sections reduces the dimmer s maximum wattage rating.

3 See the chart below for maximum wattage information. When installing more than one Cas ta Wireless dimmer in the same wallbox, it is necessary to remove inner side sections prior to wiring. See image and chart below for more AdapterWallplateLocation 1 Location 1 Location 2 Place tag - to identify wire on different color screwLocation 2 Location 14 Wireless 13 Connect the wiresGround14 Attach the wallplate bracket and Pico remote control15 Attach the wallplate snap 16 Turn power on at circuit breaker3-Way Installation - Cas ta Wireless In-Wall Dimmer with Pico Remote ControlPairing the dimmer and Pico remote control17 Press and hold "Off" button on dimmer0510156 LEDs flash18 Press and hold "Off" button on remote controlLights flash three times0510156 AdapterWallplateLocation 2 Tagged WireLocation 2 Location 2 Location 2 Location 1 Repeat steps 17 and 18 to pair additional remote Pair additional remote controlsHOLD3x5 Wireless 3-Way Installation.

4 Cas ta Wireless In-Wall Dimmer with Pico Remote ControlNeutralPico Remote ControlLine / HotTravelerCas ta Wireless Dimmer *GroundLoadLEDELLFCCFAFCINC HALS chematic DiagramTraveler* Dimmer may be installed in either WireTagged Wire6 Wireless 1 Identify existing wiringTwo switches control the lights (3-way installation)2 What you need for a 3-way installationWARNING! Shock Hazard. May result in serious injury or death. Turn off power at circuit breaker before installing the Turn power off at circuit breaker5 Remove existing switch from wall6 Tag and disconnect wires from the existing switchPlace tag - to identify wire on different color screwDifferent Color ScrewGround(Green / Bare Copper)3-Way Installation - Cas ta Wireless In-Wall Switch with Pico Remote ControlLocation 1 Location 2- If one switch controls the lights (single-pole installation) See quick-start guide that came with your switch- If three or more switches control the lights (multi-location installation) See page 41 for detailsImportant note:3 Choose a location for your Cas ta Wireless switchChoose which location you want the Cas ta Wireless switch installed in.

5 This will be Location 1 Location 1+In-wall switchPD-5WS-DVPico remote control PJ2-2B+Wallplate BracketPICO-WBX-ADAPT+Two Claro Wallplates CW-17 Wireless 7 Remove side sections (if necessary)Do not remove outside side sections on switches at the end of switch has inside side sections in the middle has all side sections Connect the new Cas ta Wireless switchTagged WireGround(Green wire )9 Mount the Cas ta Wireless switch10 Attach the wallplate snap 11 Remove existing switch from wall at Location 23-Way Installation - Cas ta Wireless In-Wall Switch with Pico Remote Control12 Tag and disconnect wires from the existing switchGround (Green / Bare Copper)Different Color Screw When installing more than one Cas ta Wireless switch in the same wallbox, it is necessary to remove inner side sections prior to wiring.

6 See image and chart below for more AdapterWallplateLocation 1 Location 1 Location 2 Place tag - to identify wire on different color screwLocation 2 Location 1 Important note:Removing side sections reduces the switch s maximum wattage rating. See the chart below for maximum wattage (120 V )LED5 A4 A3 AHalogen / incandescent600 W450 W350 WElectronic Low-Voltage600 W450 W350 WMagnetic Low-Voltage 1600 VA / 475 W450 VA / 350 W350 VA / 275 WFluorescent 25 A4 A3 AGeneral Purpose Fan3 A3 A3 APD-5WS-DV ( 277 V )LED 5 A4 A3 AHalogen / incandescent1350 W1100 W800 WElectronic Low-Voltage1350 W1100 W800 WMagnetic Low-Voltage 11350 VA / 1075 W1100 VA / 875 W800 VA / 625 WFluorescent25 A4 A3 AABCABC1 The maximum lamp wattage is determined by the efficiency of the transformer, with 70% 85% as typical.

7 For actual transformer efficiency, contact either the fixture or transformer manufacturer. The total VA rating of the transformer(s) shall not exceed the VA rating of the in-wall The in-wall switch is UL Listed for use with all magnetic and electronic fluorescent 13 Connect the wiresGround14 Attach the wallplate bracket and Pico remote control15 Attach the wallplate snap 16 Turn power on at circuit breaker3-Way Installation - Cas ta Wireless In-Wall Switch with Pico Remote ControlPairing the switch and Pico remote control17 Press and hold "Off" button on switch0510156 LED flashes18 Press and hold "Off" button on remote controlLights flash three times0510156 AdapterWallplateLocation 2 Tagged WireLocation 2 Location 2 Location 2 Location 1 Repeat steps 17 and 18 to pair additional remote Pair additional remote controlsHOLD3x9 Wireless 3-Way Installation - Cas ta Wireless In-Wall Switch

8 With Pico Remote ControlNeutralPico Remote ControlLine / HotTravelerCas ta Wireless Switch *Ground (Green)LoadLEDELLFCCFAFCINC HALS chematic DiagramTraveler* Switch may be installed in either WireTagged WireBlackBlueBlack10 Wireless 1 Identify existing wiringTwo switches control the lights (3-way installation)2 What you need for a 3-way installation+WARNING! Shock Hazard. May result in serious injury or death. Turn off power at circuit breaker before installing the Turn power off at circuit breaker5 Remove existing switch from wall6 Tag and disconnect wires from the existing switchPlace tag - to identify wire on different color screwDifferent Color ScrewGround(Green / Bare Copper)3-Way Installation - Cas ta Wireless In-Wall PRO Dimmer with Pico Remote ControlLocation 1 Location 2In-wall PRO dimmerPD-10 NXDPico remote control with wall-mounting kitPJ2-WALL- If one switch controls the lights (single-pole installation) See quick-start guide that came with your dimmer- If three or more switches control the lights (multi-location installation) See page 36 for detailsImportant note.

9 3 Choose a location for your Cas ta Wireless dimmerChoose which location you want the Cas ta Wireless dimmer installed in. This will be Location 1 Location 1 Claro Wallplate CW-1+11 Wireless 7 Remove side sections (if necessary)Do not remove outside side sections on dimmers at the end of dimmer has inside side sections in the middle has all side sections Dimmable LED WattageIncandescent/Halogen Total Wattage0 W+1000 W800 W600 W1 W 25 W+900 W750 W550 W26 W 50 W+800 W700 W500 W51 W 75 W+700 W600 W450 W76 W 100 W+600 W500 W400 W101 W 125 W+500 W400 W300 W126 W 150 W+400 W300 W200 W151 W 175 W+300 W200 W100 W176 W 200 W+200 W100 W50 W201 W 225 W+100 W50 W0 W226 W 250 W+0 W0 W0 WABCBBBCBA8 Connect the Cas ta Wireless dimmerTagged WireGround(Green wire )RedWhite ** If available, connect the neutral wire from the wallbox to the white wire on the dimmer.

10 If neutral is not available, cap the white wire with a wire connector. Neutral required for: MLV loads, LED drivers, PHPM-PA, PHPM-3F, Mount the Cas ta Wireless dimmer10 Attach the wallplate snap 11 Remove existing switch from wall at Location 23-Way Installation - Cas ta Wireless In-Wall PRO Dimmer with Pico Remote Control12 Tag and disconnect wires from the switchGround (Green / Bare Copper)Different Color ScrewImportant note:Removing side sections reduces the dimmer s maximum wattage rating. See the chart below for maximum wattage information. When installing more than one Cas ta Wireless dimmer in the same wallbox, it is necessary to remove inner side sections prior to wiring. See image and chart below for more AdapterWallplateLocation 1 Location 1 Location 2 Place tag - to identify wire on different color screwLocation 2 Location 112 Wireless 13 Connect the wiresGround14 Attach the wallplate bracket and Pico remote control15 Attach the wallplate snap 16 Turn power on at circuit breaker3-Way Installation - Cas ta Wireless In-Wall PRO Dimmer with Pico Remote ControlPairing the dimmer and Pico remote control17 Press and hold "Off" button on dimmer0510156 LEDs flash18 Press and hold "Off" button on remote controlLights flash three times0510156 AdapterWallplateLocation 2 Tagged WireLocation 2 Location 2 Location 2 Location 1 Repeat steps 17 and 18 to pair additional remote Pair additional remote controlsHOLD3x13 Wireless 3-Way