POWER AMPLIFIERS - UC Santa Barbara

Classes of Power Amplifier • Bias point amplifiers –Class-A –Class-B –Class-C • Switching amplifier –Class-E –Class-F ©James Buckwalter 22. PA Waveform • Drain current consists of DC current and AC current ©James Buckwalter i D = I D + i d i d = i pk sin (w o t) v o = - i d R 23. PA Quiescent Conditions • DC Conditions V

  Class, Amplifier

Transistor Technologies for High Efficiency and Linearity

Differential Topology • Double the available voltage swing • Even-order harmonic suppression • Double the frequency of current injection into substrate –Reduce the potential for LO-pulling • The tail current source is removed from the standard differential pair (this is a “quasi-differential” structure) –DC current set by the biasing of input devices

Phase Locked Loop Circuits

Clock generation: B. Razavi, Design of Analog CMOS Integrated Circuits, Chap. 15, McGraw-Hill, 2001. 1. Definition. A PLL is a feedback system that includes a VCO, phase detector, and low pass filter within its loop. Its purpose is to force the VCO to replicate and track the frequency and phase at the input when in lock.

  System, Design

ADS Tutorial Stability and Gain Circles ECE145A/218A

equations. The syntax is: gp_circle(S, gain, # points on circle) where S is the S-parameter matrix. Let’s illustrate. In the example below, a table is used to display frequency, maximum stable gain (MSG), the stability factor, k, and the magnitude of delta. The gain circles are at MSG (MaxGain1 in this case), and 1 and 2 dB below MSG.

  Stability, Gain, Tutorials, Circle, Tutorial stability and gain circles ece145a, Ece145a, Gain circles

Harmonic Balance Simulation on ADS

Harmonic Balance Simulation on ADS General Description of Harmonic Balance in Agilent ADS 1 Harmonic balance is a frequency-domain analysis technique for simulating nonlinear circuits and systems. It is well-suited for simulating analog RF and microwave circuits, ... function is driven to a given small value), then the resulting voltage ...

  Simulation, Driven

Quality factor, Q

When a resonant circuit is connected to the outside world, its total losses (let’s call them RP or GP) are combined with the source and load resistances, RS and RL. For example, Here is a parallel resonant circuit (C,L and RP)connected to the outside. The total Q of this circuit is called the loaded Q or QL and is given by

  Parallel, Resonant, Parallel resonant

Latches, the D Flip-Flop & Counter Design

February 6, 2012 ECE 152A - Digital Design Principles 2 Reading Assignment Brown and Vranesic 7Flip-Flops, Registers, Counters and a Simple Processor 7.1 Basic Latch 7.2 Gated SR Latch 7.2.1 Gated SR Latch with NAND Gates 7.3 Gated D …

  Latch, Sr latch

Flip-Flops and Sequential Circuit Design

11 Latches and Flip-Flops 11.5 S-R Flip-Flop 11.6 J-K Flip-Flop 11.7 T Flip-Flop 11.8 Flip-Flops with Additional Inputs 11.9 Summary 12 Registers and Counters 12.5 Counter Design Using S-R and J-K Flip-Flops 12.6 Derivation of Flip-Flop Input Equations – Summary

  Flip, Flops, Latches, Latches and flip

BASICS OF THE SPECTRUM ANALYZER - UC Santa Barbara

Fourier ⋅ π → − + + Now instead of a bank of narrow filters, we shall have one narrow filter centered at a fixed frequency, say fI, and we shall scan the signal spectrum across this filter by multiplying x(t) by a sinusoid of varying frequency f0. See Figure 1. …

  Basics, Spectrum, Analyzer, Fourier, Spectrum analyzer

Mealy and Moore Machines

February 22, 2012 ECE 152A - Digital Design Principles 5 Finite State Machines Two types (or models) of sequential circuits (or finite state machines) Mealy machine Output is function of present state and present input Moore machine Output is function of present state only Analysis first, then proceed to the design of

  States, Design, Machine, Finite, Finite state