THK Linear Motion System LM Guide
LM rail marked with "KB" after the serial number is the master LM rail. The LM block on the master LM rail has its reference surface finished to a designated precision, allowing it to serve as the positioning reference for tables. (See Figure 3-1.) LM Guides of normal grade are not marked with "KB." Therefore, any one of the LM rails
Tags:
Information
Domain:
Source:
Link to this page:
Please notify us if you found a problem with this document:
Documents from same domain
Compliant with New Accuracy Standards Caged Ball LM …
tech.thk.com2 Global Standard Type Caged Ball LM Guide SHS LM block LM rail Endplate End seal Ball cage Ball Cross section 45。 45 。 Structure of Model SHS Balls roll in four rows of raceways precision-ground on an LM rail and an LM block, and ball cages and
With, Standards, Complaints, Accuracy, Caged, Compliant with new accuracy standards caged
Mounting Procedure and Maintenance LM Guide - …
tech.thk.comMounting Procedure <Example of Mounting the LM Guide When an Impact Load is Applied to the Machine and therefore Rigidity and High Accuracy are Required >
Guide, Maintenance, Procedures, Mounting, Mounting procedure and maintenance lm guide
THK Original Grease AFE-CA Grease
tech.thk.comA THK Original Grease AFE-CA Grease Ô Base oil: high-grade synthetic oil Ô Consistency enhancer: urea-based AFE-CA Grease uses urea as a consistency enhancer and a high-grade synthetic oil as the base oil.
Models SHS-C and SHS-LC - THK Technical Support
tech.thk.comModel number coding A 5P EPXOMPBE B EFTJSFE EBUB TFBSDI GPS UIF DPSSFTQPOEJOH NPEFM OVNCFS JO UIF 5FDIOJDBM TJUF IUUQT UFDI UIL DPN Models SHS-C and SHS-LC (φH through)
Models SHS-V and SHS-LV - THK
tech.thk.comModel number coding A 5P EPXOMPBE B EFTJSFE EBUB TFBSDI GPS UIF DPSSFTQPOEJOH NPEFM OVNCFS JO UIF 5FDIOJDBM TJUF IUUQT UFDI UIL DPN Models SHS-V and SHS-LV B ¢K £ H3 M T 4-S ·ℓ W2 W W1 Model No. Outer dimensions LM block dimensions Pilot hole for side nipple Î Î Height Width Length
Caged Ball LM Guide Global Standard Size Model SHS
tech.thk.comA Types and Features Model SHS-C Speci Þ cation TableðA The ß ange of the LM block has tapped holes. Can be mounted from the top or the bottom. Used in places where the table cannot have
Features of the Ball Screw - THK Technical Support
tech.thk.comFeatures of the Ball Screw Driving Torque One Third of the Sliding Screw With the Ball Screw, balls roll between the screw shaft and the nut to achieve high ef Þ ciency.
Permissible Axial Load - THK
tech.thk.comA Permissible Axial Load <Buckling Load on the Screw Shaft > With the Ball Screw, it is necessary to select a screw shaft so that it will not buckle when the maxi-
Smooth Silent Ecological - THK Technical Support
tech.thk.comSpecial Environmental Specifications of Linear Motion Systems HSR HR HRW SR RSR SSR SHW SRS Clean Rooms HSR-M2 LM Guide with Caged Ball Technology Caged Roller LM Guide
Model DCM - THK
tech.thk.comA Lead Screw Nut D 1 PCD D Dr D o D k 4- B r 1- d H F L Unit: mm Screw shaft Screw shaft details Standard shaft length Maximum length Dynamic permis-sible thrust Static
Related documents
Product Ordering Guide - THK
www.thk.comLM Guides to be used in all orientations. Radial model SSR Page 1 SR Page 5 Machining center NC lathe Drilling machine Electric discharge machine ... 25 P Precision Notes: (12) Rail Plating-None (no symbol) F Plating (Contact THK for more Details) (13) Rail Material M Standard Stainless Steel (14) Non-Std Rail-Standard (no symbol) E S
Super-precision bearings - SKF
www.skf.comPrecision lock nuts Gauges Indexes 1. This is SKF ... and ball screws to profile rail guides – SKF can work with you to solve your most pressing linear system challenges. 9. Unit conversions Unit conversions Quantity Unit Conversion Length inch 1 mm 0.03937 in. 1 in. 25,40 mm
HIWIN Linear Guideways Catalogue [PDF] - Padia Enterprise
padiaent.combe taken into account for rail systems at rest or moving slowly. A higher level of structural safety is especially important for guides subject to impact loads, see Table 2.1. The static structural safety can be calculated using F 2.1. 2.3.4 Dynamic load rating C dyn The dynamic load rating is the defined loading (in direction and magnitude) at ...
TM-S1000 Start Here
files.support.epson.comsuch as transportation devices related to aviation, rail, marine, automotive, etc.; disaster prevention devices; various safety devices, etc.; or functional/precision devices, etc.; you should use this product only after giving consideration to including fail-safes and redundancies into your design to maintain safety and total system reliability.
Modular Multi-position Air Handlers - Trane
www.trane.comPumps (AHRI STANDARD 210/240). Refer to the Split System Outdoor Unit Product Data Guides for performance data. 2 3/4" Male Plastic Pipe (Ref.: ASTM 1785-76) PRODUCT SPECIFICATIONS MODELGAM5B0C48M41SB GAM5B0C48M41EA RATED VOLTS/PH/HZ. 208-230/1/60 RATINGS 1 SeeO.D.Specifications INDOOR COIL — Type Plate Fin Rows — …
LM Guide - THK
www.thk.comWhen using two conventional LM Guides facing each other, it took a long time to machine the table, and it was difficult to achieve the desired accuracy and adjust the clearance. With the Model HSR-YR, the tapped holes on the side of the LM block simplify the structure, which drastically reduces labor time and increases accuracy.
GUIDAGES LINÉAIRES - NTN SNR
www.ntn-snr.comdirections différentes, leur vitesse relative est donc double à la vitesse de déplacement des billes sur le rail. La surface de contact (A) étant très faible la pression de surface résultante (P) est très élevée. Ce phénomène peut provoquer la rupture du film de lubrifiant, l’échauffement des billes ainsi qu’une usure