28 VOlT INPuT 0.8 amP - Interpoint
model fmce-0528 parameter conditions min typ max units lead soldering temperature 1 10 seconds max. — — 300 °c storage temperature 1-65 — +150 °c case operating full power -55 — +125 °c
Download 28 VOlT INPuT 0.8 amP - Interpoint
Information
Domain:
Source:
Link to this page:
Documents from same domain
Mechanical: Mounting, Vibration and Shock - …
www.interpoint.comMounting on the core of an aluminum cored PC Card or other metal structure with a thermal pad interface to fill air voids would be a better thermal solution.
crane aerospace electronics power solutions LCM …
www.interpoint.comdescription The LCM-120™ line conditioning module is a non-isolated dc-dc converter used to extend the input voltage range of Interpoint’s
MHF+ Single, dual and triple dC-dC Converters
www.interpoint.comMHF+ SerieS™ SingleS and dualS DESCRIPTION Interpoint® MHF+ Series singles and duals are high frequency DC-DC converters offering a wide input voltage range of 16 to 40
sMFL single and dual dc-dc converters - Interpoint
www.interpoint.comdescription The Interpoint® SMFL Series™ 28 volt DC-DC converters are rated up to 65 watts output power over a -55°C to +125°C temperature range with a 28 volt nominal input.
28 Volt input – 40 Watt - Crane Aerospace & …
www.interpoint.comOperating COnditiOns and CharaCteristiCs input Voltage range • 16 to 40 VDC continuous for 40 W load lead soldering temperature (10 sec per pin)
270 Volt input – 65 Watt - Interpoint
www.interpoint.comElectrical Characteristics: 25°C Tc, 270 VDC Vin, 100% load, free run, unless otherwise specified. SINGLE OUTPUT MODELS MHP27005S MHP27012S units
MCh/Mgh s D DC-DC C - Interpoint - DC/DC …
www.interpoint.comFeatures small footprint, 0.79 in 2 (5.1 cm ) - MCH surface mount package - MGH • Operating temperature -55°C to +125°C • Input voltage 12 to 50 VDC • Transient protection 80 V for up to 120 ms
Quality assurance and Certification - Interpoint
www.interpoint.comQuality SyStem Overview–redmOnd and KaOhSiung • The quality management systems of Crane Electronics, Inc., Redmond and Crane Electronics Corporation, Kaohsiung have been certified to ISO 9001:2008 and AS9100C file numbers 1623564
28 Volt input 2.7 amp - Interpoint
www.interpoint.comDescription The SFMC28-461™ EMI filters provide an off-the-shelf filtering solution compliant to MIL-PRF-38534, Class H or Class K, for use in your space system.
MFX Single output DC-DC Converters - Interpoint
www.interpoint.comDeSCription The Interpoint® MFX Series™ of high efficiency DC-DC converters offers a wide input voltage range of 16 to 50 volts and up to 50 watts of output power.
Related documents
1-CHIP SERIES
atta.szlcsc.comThick Film Chip Resistors –Data Sheet 4. Marking (1) For 01005、0201 and 0402 size. Due to the very 01005、0201、0402 small size of the resistor’s body, there is no marking on the body. (2)Normally, the making of 0 0603, 0 0805, 0 1206, 0 1210, 0 1812, 0 2010,
High Performance Regenerative Receiver
www.arrl.orgA piece of an-inch-thick wood was cut to fit the inside bottom of the box. Wood screws hold the wood to the metal; they also secure the circuit board and other components to the wood. To mount the film-can coil form, I drilled a small hole in its bottom and attached it to the wood using a small brass wood screw. The wood bottom
BCD Technology and Cost Comparison 2020 - System Plus ...
www.systemplus.frThick metal layer Summary oPassives Capacitor in polysilicon Resistor in polysilicon Metal Insulator Metal Capacitor Thin Film resistors Inductors Summary o Shrink o High Voltage Foundry Technologies 41 o Infineon Roadmap SPT9 process Transistors, Insulation, Metal Layer, Passives Synthese SMART6 process
Components and Methods for Current Measurement
www.vishay.comVishay Thick Film Resistor Products: The RCWE and RCWL are typically 0.0005" to 0.002" thick, which is nearly 100 times that of thin film. The increased thickness equates to a greater mass that is better able to carry the relatively high currents and dissipate the heat across the substrate, as well as better able to manage transients.