Adjustable Shift Light Installation Instructions
Adjustable Shift Light Installation Instructions Wire Color Code Red: 12v Ignition Source (+) (switched) Green: Connects to Vehicle’s Tachometer Source Black: Vehicle Ground (-) 1. Disconnect the negative battery cable. Connecting the Power Wire Harness 2. Connect the green wire to the vehicle’s tachometer source wire.
Download Adjustable Shift Light Installation Instructions
Information
Domain:
Source:
Link to this page:
Documents from same domain
7 Color Series Wideband Air/Fuel Ratio Gauge
www.glowshift.com7 Color Series Wideband Air/Fuel Ratio Gauge For Product Numbers: GS-C702W, GS-T702W and GS-W702W Wire Color Code Yellow: Vehicle Ground12v Constant Source (+) (un-switched) Black: ( - )
7 Color Series Boost/Vacuum Gauge - glowshift.com
www.glowshift.comAdditional Installation Information & Material Requirements GlowShift Gauges Approved Conductor Wires: Successfully installing GlowShift Gauges may require lengths of wire (sizes and quantity
7 Color Series Narrowband Air/Fuel Ratio Gauge
www.glowshift.com7 Color Series Narrowband Air/Fuel Ratio Gauge For Product Numbers: GS-C702, GS-T702 and GS-W702 Wire Color Code Yellow: 12v Switched12v Constant Source (+) (un-switched) Orange: Headlamp Source (+) (optional)
Elite 10 Color Pyrometer EGT Gauge - glowshift.com
www.glowshift.comElite 10 Color Pyrometer EGT Gauge For Product Numbers: GS-ET08_1500, GS-ET08_2200, GS-EWT08_1500 and GE-EWT08_2200 Wire Harness Color Code Red: Vehicle / Engine Ground (12v Constant (un-switched) Source (+) Black: -)
7 Color Series Pyrometer EGT Gauge - glowshift.com
www.glowshift.comONE YEAR NON-TRANSFERRABLE LIMITED WARRANTY AND DISCLAIMER GlowShift Gauges, LLC ("GlowShift") warrants to the original retail consumer purchaser, and not any other purchaser or subsequent owner, that this Product will be free from defects in
Exhaust Gas Temperature Gauge - glowshift.com
www.glowshift.comSelectable Brightness Levels: The Double Vision Gauge Series features 3 selectable brightness settings for both day and night time lighting modes.
7 Color Series 35 PSI, 60 PSI, 100 PSI Boost Gauge
www.glowshift.com7 Color Series 35 PSI, 60 PSI, 100 PSI Boost Gauge For Product Numbers: GS-C701_35 GS-C701_60 GS-C701_100 GS-T701_35 GS-T701_60 GS-T701_100 GS-W701_35
7 Color Series Water Temperature Gauge - …
www.glowshift.com7 Color Series Water Temperature Gauge For Product Numbers: GS-C706, GS-T706 and GS-W706 Wire Color Code Yellow: 12v Switched 12v Constant Source (+) (un-switched) Orange: Headlamp Source (+) (optional) Red: 12v Ignition Source (+) (switched) Green: Connects to the White Wire on the Temperature Sensor Black: Vehicle Ground ( - ) 1. Disconnect the vehicle's negative …
Full Size Gauge Pillar Pod Installation Instructions
www.glowshift.comEffective 10/2014 For Full Warranty Information Please Visit GlowShift.com Full Size Gauge Pillar Pod Installation Instructions 1. Prior to installing this full size gauge pod, be sure that your vehicle does not have side curtain air bags.
Elite 10 Color Series Boost/Vacuum Gauge - …
www.glowshift.comOperating Instructions 1. 10-Color Mode: 1. Press the COLOR button to cycle between the 10 different color options. 2. The sequence of display colors are: Blue, Green ...
Related documents
Programmable Digital-7 Plus PN 7531 - Holley
documents.holley.comDigital Shift Light, PN 7542 MAP Sensor, see page 9 Replacement Harness, PN 8855 ... 4 INSTALLATION INSTRUCTIONS ... This limit is activated when 12 volts are applied to the Light Blue wire. It is adjustable from 2,000 to 12,500 rpm. Note that the Slew Rev Limiter is disabled by
Installation Instructions - Painless Performance
www.painlessperformance.comInstallation Instructions . PERFECT TORC . GM 4L60/65E and 4L80/85E . Part #66501 . 2 . ... G. Light Blue – “Upshift” H. Dark Blue – “Downshift” 13 b. If this step is overlooked there is a good possibility the Throttle ... This signal is fully adjustable to synchronize a speedometers indicated speed to the actual vehicle‟s speed ...
GSS-3000 Universal Gear Shift Sender Your new GSS-3000 ...
www.dakotadigital.comIf a Kugel or Lokar adjustable shifter is being used, you will need a Kugel nut to attach the sensor to the shift linkage. KN-3 (standard thread) and KN-4 (metric) Kugel nuts are available from Dakota Digital, Inc. When properly adjusted, the sensor arm will use most of its range of motion. If the sweep is too short,