Altivar 212 Drive - Schneider Electric
Variable speed drives for asynchronous motors ... • The Altivar 212 drive is intended for use with three-phase asynchronous motors for variable torque pump and fan applications. ... • Current analog output X–Y mA by programming X and Y from 0 to 20 mA, maximum
Download Altivar 212 Drive - Schneider Electric
Information
Domain:
Source:
Link to this page:
Documents from same domain
Table of Contents Section 4 - Schneider Electric
iportal2.schneider-electric.comDownload Section 04 PDF Table of Contents Section 4 Power Monitoring and Control ... Table 4.3: PowerLogic ION Power and Energy Meter Selection Featuresb ION8600 ION7650 ION7550 ION7350 ION7330 ION7300 ION6200 ABC Inputs, outputs and control power
Selection Guide schneider-electric.com | Mx41-730x Series
iportal2.schneider-electric.com• This equipment must only be installed and serviced by quali˜ed electrical personnel. • Read, understand and follow the instructions before installing this product. • Turn off all power supplying equipment before working on or inside the equipment.
S-Flex 212 - Schneider Electric
iportal2.schneider-electric.comSchneider Electric for any consequences arising out of the use of this material. Product Support For support and assistance, contact the Product Support Group.
TAC I/A Series JACE 645 Network Controller
iportal2.schneider-electric.comThe TAC I/A Series™ JACE 645 Network Controller is a compact, embedded-processor platform with flash memory for backup. The JACE 645 provides integrated control, supervision, and network management solutions for a network of LonWorks™-based, BACnet-based, or Modbus-based controllers
TAC I/A Series MicroNet BACnet Wiring, Networking, and ...
iportal2.schneider-electric.comThis TAC I/A Series MicroNet™ BACnet™ Wiring, Networking, and Best Practices Guide is a reference for creating a network of TAC I/A Series MicroNet BACnet controllers. This guide provides the following discussions and instructions for …
Temperature Sensors ET Series - Schneider Electric
iportal2.schneider-electric.comET Series 01 Temperature Sensors Features • Offer high accuracy and interchangeability over a wide temperature range. • Non-polarity sensitive SPECIFICATIONS For TAC Vista, I/NET, Continuum, and I/A 1000 Ohm Platinum 1000 Ohm BALCO Output 1.8K Ohms @ 77º F (25º C) Vista 10K Ohms @ 77º F (25º C) I/Net 10K Ohms @ 77º F (25º C) Continuum
Network Management Card User’s Guide
iportal2.schneider-electric.com• Any Smart-UPS® device that has an internal expansion slot, or any Symmetra® UPS except the Symmetra PX 250 or Symmetra PX 500 UPS • MEG ® Galaxy® 300, 3500, or 7000 • Expansion Chassis (AP9600) • Triple Expansion Chassis (AP9604) IPv4 initial setup You must define two TCP/IP settings for the NMC before it can operate on the network:
Power Monitoring Control - Schneider Electric
iportal2.schneider-electric.compower management systems will help you make the most of your energy by: Reducing Utility Costs & Increasing Energy Efficiency Achieve significantly r educed direct consumption-related co sts through improved efficiency, lower emissions and more accountability. And if you're a property manager, you can
EasyLogic™ PM2100 series User Manual
iportal2.schneider-electric.comfollowing special messages may appear throughout this manual or on the equipment to warn of potential hazards or to call attention to information that clarifies or simplifies a procedure. The addition of either symbol to a “Danger” or “Warning” safety label indicates that an electrical hazard exists which will result in personal injury ...
Product Catalog - Schneider Electric
iportal2.schneider-electric.comProportional band for room temperature range control: Cooling & Heating: 1.8°C ( 3.2°F ) Binary inputs: Dry contact across terminal BI1, BI2 & UI3 to Scom Outputs rating: Triac output: 30 Vac, 1 Amp. Maximum, 3 Amp. in-rush Analog: 0 to 10 Vdc into 2KΩ resistance min. Wire gauge: 18 gauge maximum, 22 gauge recommended