ARDEX FEATHER FINISH
Self-Drying, Cement-Based Finish Underlayment Self-drying, finishing underlayment ... not install ARDEX FEATHER FINISH before the primer has dried thoroughly. GYPSUM: If the substrate is a gypsum underlayment that will ... acid etching, adhesive removers, solvents and sweeping compounds are not acceptable means
Download ARDEX FEATHER FINISH
Information
Domain:
Source:
Link to this page:
Documents from same domain
TECHNICAL GUIDELINES - ARDEX Americas
www.ardexamericas.com310.2R-2013 SCTIG A SPCIIG CCRT SRAC PRPARATI R SAR S, CATIG S, POLR O RAY S, A CCRT RPAIR About ICRI Guidelines The International Concrete Repair Institute (ICRI) was
High-Performance, Waterborne Acrylic Concrete …
www.ardexamericas.comPlease note that this maintenance guide is for the use of ARDEX CG over interior ARDEX toppings. For the maintenance of other ARDEX finishes, please visit
ARDEX Liquid BackerBoard
www.ardexamericas.comARDEX Liquid BackerBoard ® Self-Leveling Underlayment for Interior Wood and Concrete Subfloors Description and Usage ARDEX Liquid BackerBoard® Self …
ARDEX FEATHER FINISH - ARDEX Americas Home
www.ardexamericas.comARDEX FEATHER FINISH® Self-Drying, Cement-Based Finish Underlayment Recommended Tools ARDEX T-2 Ring Mixing Paddle, mixing bucket, margin trowel, steel trowel, razor scraper, and a 1/2” (12 mm) heavy-duty
ARDEX CP
www.ardexamericas.comARDEX CPTM Concrete Patch Description and Usage ARDEX CPTM is a trowel-grade, cementitious topping for filling and repairing areas of indoor and outdoor concrete above, on or below grade. Engineered with Portland
ARDEX MCTM RAPID
www.ardexamericas.comIf the concrete substrate is too uneven to provide a uniform film thickness of the ARDEX MC RAPID (typically CSP #6 or higher), the substrate can be pre-smoothed using ARDEX K 301TM Self-Leveling Exterior Concrete Topping, ARDEX MRPTM Moisture Resistant Patch or ARDEX K 60TM ARDITEX in certain situations.
Self-Leveling Concrete Topping - Ardex
www.ardexamericas.comaddition of ARDEX E 25TM Resilient Emulsion is required to increase the resiliency of the ARDEX K 520. Mix 2 quarts (1.9 L) of ARDEX E 25 with 4.5 quarts (4.25 L) of water for each bag of ARDEX K 520 following the mixing instructions above. Please note that, if ARDEX E 25 is used, the ARDEX K 520 must first cure 24 hours
ARDEX CP
www.ardexamericas.comfilling and repairing areas of indoor and outdoor concrete above, on or below grade. Engineered with Portland cement and select high-performance polymers, ARDEX CP readily bonds to concrete surfaces. It is easy to apply, hardens quickly, is freeze-thaw resistant, and produces a surface finish that is suitable for foot and rubber tire traffic.
Related documents
Laboratory Exhaust Systems - Greenheck-USA
content.greenheck.comThe Vektor®-H is a cost-effective, self-contained, ... primer, is applied. • Step 3: The finish coat of polyester resin (Hi-Pro Polyester), a super durable class of ... 2 - Surface etching, severe staining, but film integrity remains 3 - Significant pitting, cratering, swelling, or …
ArmorSeal ARMORSEAL 8100 Heavy WATER BASED EPOXY …
spectrumpainting.compockets and other voids with Steel-Seam FT910. Primer required. Follow the standard methods listed below when applicable: ASTM D4258 Standard Practice for Cleaning Concrete. ASTM D4259 Standard Practice for Abrading Concrete. ASTM D4260 Standard Practice for Etching Concrete. ASTM F1869 Standard Test Method for Measuring Moisture Vapor
RODUCT NO 1249-50, 51 - QUIKRETE
www.quikrete.comSelf-Leveling Floor Resurfacer (No. 1249-51) produce a smooth surface ... Acid etching, solvents, and sanding are not acceptable means for preparing the substrate. If installing over wood floors, reinforce to prevent flexing of the floor. Seal all perimeter openings to retain leakage. ...