Building work that does not require a building consent

C/AS2 - Acceptable Solution for Acceptable Solution for ...

C/AS2 Acceptable Solution for Buildings with Sleeping (non institutional) (Risk Group SM) For New Zealand Building Code Clauses C1-C6 Protection from Fire

Earthquake geotechnical engineering practice

Earthquake geotechnical engineering is a highly specialised field. As such the investigations for this need to be developed and carried out by an appropriately qualified and experienced geotechnical engineer or engineering geologist (referred to herein as the geotechnical professional). For the purposes of this document ‘geotechnical

  Geotechnical

E2 External Moisture

For single- and two-storey concrete and concrete masonry construction within specific limitations: E2/AS3. For light steel framed buildings up to 3 storeys, within specific limitations: E2/AS4. E2.3.3 Ground contact or proximity All walls, floors and structural elements in ground contact or proximity, except for buildings where external

  Light, Concrete

Module 6: Earthquake resistant retaining wall design

guidance on earthquake design aspects for retaining . structures that are not well covered in these handbooks or elsewhere. The main objective is to identify situations where seismic design of retaining structures should be considered, to provide the necessary seismic parameters, and to identify key issues relating to seismic design.

  Design, Seismic, Structure, Walls, Module, Resistant, Seismic design, Retaining, Earthquake, Module 6, Retaining structures, Earthquake resistant retaining wall design

Worked Example 4 | Design of a tied-back retaining wall to ...

Design of a tied-back retaining wall to resist earthquake loading . Worked example to accompany MBIE Guidance on the seismic design of retaining structures for residential sites in Greater Christchurch (Version 2) November 2014 . Tied-back retaining walls were used originally as a substitute for braced retaining walls in deep excavations.

  Design, Seismic, Structure, Walls, Loading, Seismic design, Retaining, Earthquake, Sisters, Retaining structures, Retaining wall to resist earthquake loading

Acceptable Solutions and Verification Methods

4.2 Sizing of downpipes 42 4.3 Installation of downpipes 42 5.0 Roof Gutters 42 5.1 Size of roof gutter 42 5.2 Materials44 5.3 Gradients44 5.4 Thermal movement 44 5.5 Overflow outlets 44 Appendix A Rainfall intensities 45 Index 47 Contents Amend 4 Dec 2000 Amend 4 …

  Verification, Solutions, Methods, Acceptable, Roof, Appendix, Sizing, Acceptable solutions and verification methods

Acceptable Solutions and Verification Methods

4.2 Sizing of downpipes 42 4.3 Installation of downpipes 42 5.0 Roof Gutters 42 5.1 Size of roof gutter 42 5.2 Materials44 5.3 Gradients44 5.4 Thermal movement 44 5.5 Overflow outlets 44 E1/AS1 Appendix A Rainfall intensities 45 Acceptable Solution E1/AS2 52 1.0 AS/NZS 3500.3 Stormwater Dec 2000 drainage52 Index 56 Contents Amend 4

  Verification, Solutions, Methods, Acceptable, Roof, Appendix, Sizing, Acceptable solutions and verification methods

Commentary for Acceptable Solutions C/AS1 to C/AS7 ...

December 2013. Contents Acceptable Solutions C/AS1 to C/AS7 Part 1: General 2 ... 4.11 Protected shafts 31 4.13 Floors 32 4.14 Subfloor spaces 32 ... INNOVATION AND EMPLOYMENT – 15 FEBRUARY 2013 I 1 Part 5: Control of external fire spread 34 5.1 General principles 34 5.2 Horizontal fire spread from external walls 36 5.5 Table method for ...

  2013, December, December 2013

Constructing Cavities - Building Performance

Table 23 (’Properties of roof underlays and building wraps‘). Install the wall underlay directly over the framing. Install the cavity battens directly over the wall underlay as described in Cavity battens on page 9. No additional wall underlay is needed between the wall cladding and the cavity battens except in the following situations.

  Building, Constructing, Wrap, Cavities, Building wraps, Constructing cavities

Earthquake geotechnical engineering practice

2 Site and liquefaction considerations 2.1 Site characterisation One of the initial steps in the design of ground improvement is to develop a geotechnical model for the site which fits within the wider regional geology and geomorphology. This starts from review of …

  Practices, Site, Characterisation, Site characterisation

Exporting to Europe and CE Marking

Exporting to Europe . And CE Marking . CE Marking is currently required for many products sold in Europe, yet many U.S. exporters are still unsure

  Marking, Exporting, Europe, Exporting to europe and ce marking, Exporting to europe, And ce marking

HID Inspection Guide Offshore - Health and Safety …

HID Inspection Guide Offshore. Inspection of Mechanical Handling & Crane Operations Contents Summary Introduction Action Background Appendix 1 - The planning of mechanical handling operations and crane

  Guide, Inspection, Offshore, Hid inspection guide offshore

Application of health and safety law offshore

Page 1 of 5 Health and Safety Executive Application of health and safety law offshore Guidance on the legislative changes introduced by the Health and Safety

  Health, Applications, Guidance, Safety, Offshore, Application of health and safety law offshore, Application of health and safety law offshore guidance

Understanding the Machinery Directive (2006/42/EC)

Understanding the Machinery Directive (2006/42/EC) Brief History . In 1985, a series of ‘New Approach Principles’ were introduced into the European

  Understanding, Directive, 2006, Machinery, Understanding the machinery directive

Annex G Appendix 6 Hazard Identification, and Risk ...

For additional guidance as to required areas of competence, see Significant Hazards table below . General Health and Safety Aspects Control of Substances Hazardous to Health management

  Guidance, Hazards

Guide to lifting equipment testing inspections …

Lifting equipment training, plant audits, registers and codes of practice. P O Box 3757, CRAMERVIEW, 2060 RSA • Tel / Fax: +27 11 462 9620/1 • Cell +27 82 372 4595

  Testing, Inspection, Equipment, Lifting, To lifting equipment testing inspections

DMRB VOLUME 1 SECTION 3 PART 8 - BA 57/01 - …

BA 57/01 Design for Durability Summary: The existing Standard and Advice Note (BD 57 and BA 57) have been updated to include: a) Lifting of the moratorium on internal grouted post-tensioned construction

  Lifting

2018/19 PLANNING GUIDANCE: NHS PROVIDERS …

2 February 2018 NHS Providers | ON THE DAY BRIEFING | Page 1. 2018/19 PLANNING GUIDANCE: NHS PROVIDERS ON THE DAY BRIEFING . Today’s planning guidance is a refresh of plans already prepared under the two-year

  Guidance, Planning, Provider, 19 planning guidance, Nhs providers, Nhs providers on