CLD Structural Cavity Batten Technical Specification
This specification covers the use of Titan Façade Panel on buildings, where the maximum wind pressure exerted on the building façade is up to 2.5kPa (ULS). This specification is intended for use by architects or designers/ specifier and installers who …
Download CLD Structural Cavity Batten Technical Specification
Information
Domain:
Source:
Link to this page:
Documents from same domain
Technical Specification - jameshardie.co.nz
www.jameshardie.co.nzLinea® Weatherboard Technical Specification April 2016 New Zealand 3 1 Application and scope 1.1 APPLICATION Linea® Weatherboard is …
Design Manual - jameshardie.co.nz
www.jameshardie.co.nzFire and Acoustic Design Manual August 2017 New Zealand 3 1 Introduction readers are familiar with the relevant James Hardie cladding and lining product literature.
Vertical Installation Technical Specification
www.jameshardie.co.nzThis specification also covers the installation of Linea Oblique Weatherboard on projects, which are subject to specific engineering design (SED) up to a wind pressure of 2.5kPa (ULS). 1.3 DETAILS Various typical Linea Oblique Weatherboard vertical construction details are provided in the Details section of this document.
Design Manual - James Hardie
www.jameshardie.co.nzFigure 1: Vertical junction between Linea™ Weatherboard and James Hardie flat sheet cladding Figure 2: Vertical junction between Linea™ Weatherboard and James Hardie flat sheet cladding 4 James Hardie Cladding Junction Details Design Manual November 2016 New Zealand Flexible underlay Linea™ Weatherboard Scriber 60 x 3.15mm jolt head
Fire & Acoustic - James Hardie
www.jameshardie.co.nz3.1 External Walls - Timber Frame 8 3.2 External Walls - Steel Frame 10 3.3 Parapet & Wing Walls ... S - StriaTM Cladding ... Refer to recommended safe working practices in each specific product technical specification or installation manual
Design Manual - James Hardie
www.jameshardie.co.nzThe specifier or other party responsible for the project must run through a risk matrix analysis as per E2/AS1 to determine which construction method is applicable to install the external cladding on the project. The designer must also ensure that the bracing capacities published in this specification are appropriate for the intended application.
jameshardie.co.nz CLD Structural Cavity Batten
www.jameshardie.co.nzPortland cement, ground sand, cellulose fibre and water. The product is easily identified by the name 'Stria Cladding' printed on the back of the panels. CLD Structural Cavity Batten is manufactured using a low density fibre cement formulation. The basic composition is Portland cement, ground sand, cellulose fibre, water and proprietary additives.
Related documents
WINDEX® GLASS & MORE MULTI-SURFACE
content.oppictures.comSafety Data Sheet according to Hazard Communication Standard; 29 CFR 1910.1200 WINDEX® GLASS & MORE MULTI-SURFACE Version 1.4 Print Date 10/02/2020 Revision Date 06/20/2019 SDS Number 350000014153
22C-TD001F-EN-P PowerFlex 400 Adjustable Frequency AC ...
literature.rockwellautomation.commounting in an air handling system. I/O • Three semi-programmable and four fully programmable digital inputs provide application versatility. • Two programmable form C relay outputs and one opto output can be used to indicate various drive or motor conditions. • Two analog outputs are DIP switch selectable for either voltage (0…10V) or
GENERAL SPECIFICATION FOR AIR-CONDITIONING, …
www.archsd.gov.hkThis General Specification aims to lay down the technical requirements of materials and equipment, the standards of workmanship, the requirements on testing and ... B10.2 System Static Pressure Gauges for Air Distribution Systems . B10.3 Thermometers - Air Immersion . ... B11.5 Ductwork and Air Handling Plant - Methods of Application ...
GENERAL SPECIFICATION FOR PLUMBING INSTALLATION IN ...
www.archsd.gov.hkThis General Specification aims to lay down the technical requirements of materials and equipment, the standards of workmanship, the requirements on testing and ... Pilot Type Pressure Reducing Valves . C1.8 . Cisterns and Tanks : SECTION C2 . WATER HANDLING EQUIPMENT . ... Specification General Specification for Air-conditioning, Refrigeration ...
MECHANICAL AND ELECTRICAL TECHNICAL SPECIFICATION
www.ebrd.comY:\00-Enquires\E4340\4.0 FHP Specifications\4.8 Combined M&E\E4340 M&E Technical Specification.docx 5 ‘Provision Works’ shall mean and include all equipment to be provided and work to be done under the contract and shall include supplying, fixing, testing, regulation and commissioning of
Surface-Mount QuickPort Boxes - Leviton
www.leviton.comSPECIFICATION The surface-mount box shall be small and low profile to accept up to twelve field-configurable QuickPort connectors. Base shall include cable anchor points. Mounting methods shall include screws and pressure-sensitive adhesive. 2-, 4-, 6-, and 12-port boxes shall accept magnet (41030-SMJ) for mounting on steel surfaces.