Finishing Drywall 5 Systems - USG
other areas with pedestrian traffic. Tape and fastener heads need not be covered with joint compound. Surface shall be free of excess joint compound. Tool marks and ridges are acceptable. Level 2May be used with setting-type compound for areas where water-resistant gypsum backing board, specification ASTM C630, is used as a substrate for tile.
Download Finishing Drywall 5 Systems - USG
Information
Domain:
Source:
Link to this page:
Please notify us if you found a problem with this document:
Documents from same domain
USG Fire-Resistant Assemblies Catalog (English) - …
www.usg.com4 USG Fire-Resistant Assemblies Fire Protection USG is the undisputed leader among building material manufacturers in providing products and systems designed to keep people safe from fire.
USG Area Separation Wall Systems Brochure …
www.usg.comArea separation walls between adjoining townhouses must provide fire-resistive ratings to ensure the safety of occupants in adjacent dwellings.
System, Area, Safety, Walls, Brochure, Separation, Usg area separation wall systems brochure
Fire-Resistant Assemblies Brochure (English) - SA100
www.usg.comUser’s Guide Use this brochure to determine fire ratings for CGC products and systems. This brochure provides: — Comprehensive information about fire-rated assemblies
Fire, English, Brochure, Resistant, Assemblies, Fire resistant assemblies brochure, Sa100
Technical Document Seismic Technical Guide - USG
www.usg.com4 Hanger Wire Attachment Application Anchorage The International Building Code (IBC), through references to ASCE/SEI 7 Minimum Design Loads for Buildings and Other Structures, American Society of Civil Engineers/Structural Engineering Institute (ASCE/SEI), defines
American, Guide, Design, Seismic, Document, Engineer, Technical, Society, Case, Minimum, Load, Civil, American society of civil engineers, Technical document seismic technical guide, Sei 7 minimum design loads
Technical Document Seismic Technical Guide - USG
www.usg.comTechnical Seismic Technical Guide Document Light Duty Suspension Systems ASTM C6351 addresses the load carrying capability of main tees, categorizing them as Light, Intermediate or Heavy Duty.
CGC SHAFT WALL SYSTEMS - USG
www.usg.comC-H studs in a progressive manner, with gypsum panels, gypsum fiber panels or cement board applied to the face. All details, specifications and data contained in this literature are intended as a …
USG DUROCK BRAND CEMENT BOARD SYSTEMS
www.usg.comSTANDARDS USG Durock® cement board exceeds ANSI standards for cementitious backer units (CBU). See ANSI A118.9 for test See ANSI A118.9 for test methods and specifications for CBU and ANSI A108.11 for interior installation of CBU.
Manual Técnico USG Tablaroca® (Español)
www.usg.comUSG Manual Técnico USG TABLAROCA® USG SHEETROCK® Manejo, almacenaje, especificación, instalación y recomendaciones generales.
0 ICC-ES Evaluation Report ESR-1222 - USG
www.usg.comThe USG suspended ceiling framing systems described in this report are suspended, exposed framing, concealed ceiling assemblies used in fire-rated and non -resistance -
Technical Document Seismic Technical Guide - USG
www.usg.comTechnical Seismic Technical Guide Document Compression Posts USG Donn® Brand Compression Post providesidrig support for a ceiling suspension system in seismic applications. Telescoping compression posts attach to the main tees at each splayed wire location, preventing upward
Guide, Seismic, Document, Technical, Technical document seismic technical guide
Related documents
SAE and Metric Fastener Torque Specifications
manuals.gogenielift.comFastener Torque Specifications : Service Manual Supplement July 2016 Fastener Torque Specifications 4 SAE and Metric Fastener Torque Specifications SAE Plain and Zinc Plated Hex and Socket Head Cap Screws TORQUE CHART - SAE PLAIN AND ZINC PLATED HEX HEAD AND SOCKET HEAD CAP SCREWS:
Maintenance Schedule - American Honda Motor Company
techinfo.honda.comfastener's head until it pops in. Pull the lining back. 3. Remove the socket from the light assembly by turning it one-quarter turn counterclockwise. 4. Remove the bulb by turning it one-quarter turn counterclockwise. 5. Install the new bulb in the socket. Turn it clockwise to lock it in place. 6. Reinstall the socket. Turn it clockwise until ...
SECTION DETAIL – PANEL WITH HORIZONTAL TRIM
www.jameshardiepros.comFor fastener specifications and complete installation instructions refer to appropriate documentation at www.JamesHardieCommercial.com. 0 SCALE: 1" = 4" 2" 4" HORIZONTAL TRIM CAN ALSO BE HARDIE REVEAL2.0™ PANEL VERTICAL SIDING USED AT THE FLOOR BREAK; HOWEVER A DRAINAGE FLASHING IS REQUIRED TO BE USED EVERY OTHER …
MASTER SPECIFICATIONS Division 08 OPENINGS
www.northwestern.edumaster specifications: division 08 – openings . section # title 08 1113 hollow metal doors and frames . 08 1119 stainless steel doors and frammes . 08 1416 flush wood doors . 08 1433 thermal fused stile and rail wood doors . 08 3113 access doors and frames . 08 4113 aluminum-framed entrances and storefronts . 08 4413 glazed aluminum curtain walls
MASTER SPECIFICATIONS Division 09 FINISHES
www.northwestern.edu2. Power-Actuated Anchors: Fastener system of type suitable for application indicated, fabricated from corrosionresistant materials, with allowable load capacities calculated - according to ICC-ES AC70, greater than or equal to the design load, as determined by testing per ASTM E 1190 conducted by a qualified testing agency.
m Fastener Handbook F=Q+ 100 BOLT PRODUCTS
www.westcoastfasteners.com.auThis may lead to the specifications being changed without notice. ISSUE 99 PAGE 2 90138AjxH/bk99IndexPgs1-8•10 13/7/00 10:11 AM Page 2. INDEX - FASTENER HANDBOOK PRODUCT DESCRIPTION SECTION PAGE FORWARD 9-10 HEAD MARKING 1 11-13 Nut Marking 13 STANDARD BOLT PRODUCT RANGES 2 14-15 ISO Metric 14