SECTION DETAIL – PANEL WITH HORIZONTAL TRIM
For fastener specifications and complete installation instructions refer to appropriate documentation at www.JamesHardieCommercial.com. 0 SCALE: 1" = 4" 2" 4" HORIZONTAL TRIM CAN ALSO BE HARDIE REVEAL2.0™ PANEL VERTICAL SIDING USED AT THE FLOOR BREAK; HOWEVER A DRAINAGE FLASHING IS REQUIRED TO BE USED EVERY OTHER …
Tags:
Specification, Fastener, Fastener specifications
Information
Domain:
Source:
Link to this page:
Please notify us if you found a problem with this document:
Documents from same domain
HardiePlank Lap Siding Product Description - …
www.jameshardiepros.comGeneral Product Information Tools for utting and Fastening General Installation Reuirements General Fastener Reuirements Finishing and aintenance
Product, Descriptions, Siding, Lap siding product description
Installation Guide - James Hardie Pros
www.jameshardiepros.com1 | English CUTTING CEMENT HARDIEBACKER® BOARD • Use a straight edge as a guide to score the board’s face and snap upward …
HardieTrim Boards Products Description - James …
www.jameshardiepros.comHardieTrim boards, /4! /4 HardieTrim 5/4, 4/4 boards that should get two ®
Product, Descriptions, Board, Hardietrim boards products description, Hardietrim, Hardietrim boards
TR1509 HardieTrim HZ Installation ... - James Hardie …
www.jameshardiepros.comjoist 1 in. min. water resistive siding barrier flashing deck material ledger trim flashing FLASHING/CLEARANCE REQUIREMENTS NO-COVER vertical trim 1/4 in. min.
Fastening Tips for HardiePlank Lap Siding …
www.jameshardiepros.comIMPORTANT: Failure to install and fi nish this product in accordance with applicable building codes and James Hardie written application instructions
Tips, Fastening, Siding, Hardieplank, Fastening tips for hardieplank lap siding
Evaluation Report ESR 2290 - James Hardie Pros
www.jameshardiepros.comICC-ES Evaluation Reports are not to be construed as representing aesthetics or any other attributes not specifically addressed, nor are they to be construed
Evaluation Report ESR 1844 - Fiber Cement Products
www.jameshardiepros.comESR-1844 | Most Widely Accepted and Trusted Page 2 of 6 4.2 Installation: 4.2.1 General: 8The manufacturer’s published installation instructions and this report must be strictly adhered to and a copy of this report and the instructions must be available
HardiePlank Lap Siding - James Hardie Pros
www.jameshardiepros.comIMPORTANT: To prevent damage to the drip edge, extra care should be taken when removing planks from the pallet, while handling, and when installing with a lap gauge.
INSTALLATION INSTRUCTIONS - James Hardie Pros
www.jameshardiepros.comHardie. This document is intended for use by builders, cladding installers, and other contractors who may be involved with the installation of the Reveal Panel System. The Reveal PanelSystem by James Hardie provides a durable, expressed joint panel appearance for building facades offering versatility to architects and builders.
Exterior Wall Drainage Requirements - James Hardie Pros
www.jameshardiepros.coma 3/8 inch air gap (i.e. rainscreen) between flat-to-wall siding and the water-resistive barrier as a best practice. James Hardie recommends that you consult with your design professional if you have questions regarding exterior wall drainage on your single-family project. Individual buildings All exterior cladding products, including hard siding,
Related documents
SAE and Metric Fastener Torque Specifications
manuals.gogenielift.comFastener Torque Specifications : Service Manual Supplement July 2016 Fastener Torque Specifications 4 SAE and Metric Fastener Torque Specifications SAE Plain and Zinc Plated Hex and Socket Head Cap Screws TORQUE CHART - SAE PLAIN AND ZINC PLATED HEX HEAD AND SOCKET HEAD CAP SCREWS:
m Fastener Handbook F=Q+ 100 BOLT PRODUCTS
www.westcoastfasteners.com.auThis may lead to the specifications being changed without notice. ISSUE 99 PAGE 2 90138AjxH/bk99IndexPgs1-8•10 13/7/00 10:11 AM Page 2. INDEX - FASTENER HANDBOOK PRODUCT DESCRIPTION SECTION PAGE FORWARD 9-10 HEAD MARKING 1 11-13 Nut Marking 13 STANDARD BOLT PRODUCT RANGES 2 14-15 ISO Metric 14
MASTER SPECIFICATIONS Division 09 FINISHES
www.northwestern.edu2. Power-Actuated Anchors: Fastener system of type suitable for application indicated, fabricated from corrosionresistant materials, with allowable load capacities calculated - according to ICC-ES AC70, greater than or equal to the design load, as determined by testing per ASTM E 1190 conducted by a qualified testing agency.
MASTER SPECIFICATIONS Division 08 OPENINGS
www.northwestern.edumaster specifications: division 08 – openings . section # title 08 1113 hollow metal doors and frames . 08 1119 stainless steel doors and frammes . 08 1416 flush wood doors . 08 1433 thermal fused stile and rail wood doors . 08 3113 access doors and frames . 08 4113 aluminum-framed entrances and storefronts . 08 4413 glazed aluminum curtain walls
Maintenance Schedule - American Honda Motor Company
techinfo.honda.comfastener's head until it pops in. Pull the lining back. 3. Remove the socket from the light assembly by turning it one-quarter turn counterclockwise. 4. Remove the bulb by turning it one-quarter turn counterclockwise. 5. Install the new bulb in the socket. Turn it clockwise to lock it in place. 6. Reinstall the socket. Turn it clockwise until ...
Finishing Drywall 5 Systems - USG
www.usg.comother areas with pedestrian traffic. Tape and fastener heads need not be covered with joint compound. Surface shall be free of excess joint compound. Tool marks and ridges are acceptable. Level 2May be used with setting-type compound for areas where water-resistant gypsum backing board, specification ASTM C630, is used as a substrate for tile.