NI 9215 Datasheet
Securement type Screw flanges provided Torque for screw flanges 0.2 N · m (1.80 lb · in.) Weight NI 9215 with screw terminal 150 g (5.3 oz) NI 9215 with spring terminal 138 g (4.9 oz) NI 9215 with BNC 173 g (6.1 oz) NI 9215 with Screw Terminal and NI 9215 with Spring Terminal Safety Voltages Connect only voltages that are within the following ...
Download NI 9215 Datasheet
Information
Domain:
Source:
Link to this page:
Documents from same domain
Using Acoustic Beamforming for Pass-By Noise …
www.ni.comUsing Acoustic Beamforming . for Pass-By Noise Source Detection . NATIONAL INSTRUMENTS. APPLICATION NOTES. Abstract. This application note discusses a technique known as beamforming for determining noise location of passing
GETTING STARTED GUIDE to ±10 V, 16 Bit, 250 …
www.ni.comMeasurement Category I is for measurements performed on circuits not directly connected to the electrical distribution system referred to as MAINS voltage.
NI 6509 User Guide and Specifications - National …
www.ni.comUSER GUIDE AND SPECIFICATIONS NI 6509 This document contains information about using the NI PCI-6509, NI PXI-6509, and NI PCIe-6509 data acquisition devices with the
NI 6528/6529 User Guide and Specifications - …
www.ni.comNI 6528/6529 User Guide and Specifications 6 ni.com Operate the DIO device only at or below Pollution Degree 2. Pollution is foreign matter in a solid, liquid, or gaseous state that can reduce dielectric
PXIe-5820 Getting Started Guide - National …
www.ni.comElectromagnetic Compatibility Guidelines This product was tested and complies with the regulatory requirements and limits for electromagnetic compatibility (EMC) stated in the product specifications.
DEVICE SPECIFICATIONS NI 6722/6723
www.ni.comDEVICE SPECIFICATIONS NI 6722/6723 This document lists the specifications for the NI 6722/6723 analog output devices. The following specifications are typical at 25°C unless otherwise noted.
NI cRIO-9030 Specifications - National Instruments
www.ni.comSPECIFICATIONS NI cRIO-9030 Embedded CompactRIO Controller with Real-Time Processor and Reconfigurable FPGA This document lists the specifications for the National Instruments cRIO-9030.
NI PS-15 Power Supply User Manual and …
www.ni.com©National Instruments Corporation viii NI PS-15 Power Supply User Manual About This Manual The NI PS-15 Power Supply User Manual describes the features and specifications of the NI PS-15 power supply and contains information
NI cDAQ -9191
www.ni.comDigital output sample clock frequency Streaming from application memory System-dependent Regeneration from FIFO 0 MHz to 10 MHz Finite 0 MHz to 10 MHz
NI PXIe-1435 User Guide and Specifications - …
www.ni.comNI PXIe-1435 User Guide and Specifications The NI PXIe-1435 (NI 1435) is a PXI Express (PXIe) image acquisition device that supports Base, Medium, Full, and Extended Full configuration Camera Link cameras and supports Power over Camera
Related documents
Flansche ASME Flanges - rff
www.rff.derff.de 35 ASME B 16.5 Nenndrücke, Bemaßung und Dichtflächen Classes, Dimensions and Facings ASME Class 150 300 400 600 900 1500 2500 bar ~ 20 51 68 102 140 153 210 233 350 422 700 1050 1400 psi ~ 285 740 990 1480 2220 3380 6120 API psi 2000 3000 5000 10000 15000 20000 Nenndruckvergleich Class / bar / psi / API psi
PIPING MATERIAL CLASS DESCRIPTION - Washington
fortress.wa.govPiping Material Class Description . 1 Introduction . This document describes the minimum requirements for the piping material classes for the River Protection Project - Waste Treatment Plant. It summarizes the piping material requirements for pipe, fittings, flanges, valves, and all other piping components for each specific pipe class as ...
Process Interface Valves - Swagelok
www.swagelok.com316/316L Working Pressure by Class, bar Temperature °C ASME Class 150 300 600 900 1500 2500 Working Pressure, bar –29 to 38 50 100 150 200 19 .0 18 .4 16 .2 14 .8 13 .7 49 .6 48 .1 42 .2 38 .5 35 .7 99 .3 96 2 84 4 77 0 71 .3 148 .9 144 .3 126 6 115 107 .0 248 .2 240 .6 211 .0 192 178 .3 413 .7 400 .9 351 6 320 8 297 .2 250 300 325 350
Type 3241-1 and Type 3241-7 Pneumatic Control Valves Type ...
www.samsongroup.comPressure rating Class 125 250 150/300 300 Type of connection Flanges FF – RF 1) RF 1) Welding ends – – ASME B16.25 – Thread – NPT – – Seat-plug seal Metal seal · Soft seal · High-performance metal seal Characteristic Equal percentage · Linear (according to Information Sheet u …
DT Series Technical Manual - Farnell
www.farnell.commounting, clips, brackets and flanges. Deutsch DT Bussed Series 2 3 Integral Connector Latch Rugged Thermoplastic Housing-55o C to +125o C Operating Temperature Available Configurations: DTM/DT 2, 3, 4, 6, 8 & 12 - Size 20/16 DTP 2 & 4 - Size 12 DTHD 1 - Size 4, 8 & 12 Silicone Seals: DTM: Accepts AWG 22 - 16 wire DT: Accepts AWG 20 - 14 wire
Cerabar S PMC71, PMP71, PMP75 (BA) - Endress+Hauser
portal.endress.comreference temperature of 20°C (68°F) or 100°F (38°C) for ASME flanges. • The pressure values permitted at higher temperatures can be found in the following standards: – EN 1092-1: 2001 Tab. 18 1) – ASME B 16.5a – 1998 Tab. 2-2.2 F316 – ASME B 16.5a – …