Recommended Soldering Techniques
: Solder may not adhere to the leads or terminals of a device if the plating thickness is too thin. This problem especially applies to axial-leaded devices since the solder must bridge across the through-hole from the pad to the lead (Figure 8). 2.
Download Recommended Soldering Techniques
Information
Domain:
Source:
Link to this page:
Documents from same domain
Description Pin Assignments ADVANCE ... - Diodes …
www.diodes.comAL5802 Document number: DS35516 Rev. 9 - 2 2 of 11 www.diodes.com March 2014 © Diodes Incorporated ADVANCE INFORMATION NEW PRODUCT AL5802 Pin …
GND 1 8 ADJ/NC EN 2 7 OUT IN 3 6 OUT ... - Diodes …
www.diodes.comAP7362 Document number: DS35058 Rev. 7 - 2 © Diodes Incorporated 2 of 15 www.diodes.com May 2016 AP7362 Shutdown Pin Descriptions Pin Number Pin Name Function 1 GND ...
AL5809 X 60V Two Terminal Constant Current LED …
www.diodes.comAL5809 Document number: DS36625 Rev. 5 - 2 © Diodes Incorporated 1 of 16 www.diodes.com December 2016 AL5809 60V Two Terminal Constant Current LED Driver PowerDI Description
AP2337 - Diodes Incorporated
www.diodes.comAP2337 1.0A SINGLE CHANNEL CURRENT-LIMITED LOAD SWITCH AP2337 Document number: DS35060 Rev. 2 - 2 1 of 10 www.diodes.com October 2011 © Diodes …
VF MAX IR MAX Low Forward Voltage Drop VR F @ …
www.diodes.comTitle: BAS70TW /DW-04 /DW-05 /DW-06 /BRW Author: Diodes Incorporated Subject: SURFACE MOUNT SCHOTTKY BARRIER DIODE ARRAYS Keywords
ZXBM5210 Description Pin Assignments
www.diodes.comZXBM5210 Document number: DS36765 Rev. 1 - 2 www.diodes.com December 2013 © Diodes Incorporated NEW PRODUCT ZXBM5210. control signal at PWM pin.
BSS84 - Diodes Incorporated
www.diodes.comBSS84 Document number: DS30149 Rev. 22 - 2 © Diodes Incorporated 1 of 6 www.diodes.com May 2017 BSS84 P-CHANNEL ENHANCEMENT MODE MOSFET Product Summary BV DSS R DS(ON) max
PI7C9X2G404SL - Diodes Incorporated
www.diodes.comDocument Number DS40068 Rev 2-2. PI7C9X2G404SL PCI EXPRESS GEN 2 PACKET SWITCH . 4-Port, 4-Lane, SlimPacket PCIe2.0 Packet Switch . DATASHEET. REVISION …
A Product Line of Diodes Incorporated
www.diodes.comTitle: ZXRE1004 Author: Diodes Incorporated Subject: SOT23 MICROPOWER (4μA) 1.22V VOLTAGE REFERENCE Keywords: ZXRE1004 SOT23 MICROPOWER (4μA) 1.22V VOLTAGE REFERENCE SOT23 • High performance alternative to REF1004, LT1004 and LM185/385 references • 4μA typical knee current • Small outline SOT23 …
General Description Features - Diodes Incorporated
www.diodes.comGeneral Description ... · 36V 500mA Rugged Integrated Bipolar Switch ... BCD Semiconductor Manufacturing Limited reserves the right to make changes without further ...
Related documents
Through Hole Solder Joint Evaluation
www.ipctraining.orgThrough Hole solder joint evaluation, and therefore, it references portions of the fol-lowing IPC standard: The IPC-A-610 Rev. F, Acceptability of Electronic Assemblies, which illustrates the requirements for many types of solder connections. Classification Through Hole solder joint requirements are divided into three classes depending
Miniature Signal Relays EC2/EE2
content.kemet.com• Surface mount and through-hole options • High Breakdown Voltage (NKX) type can withstand 1.5 kVAC at open contacts Overview The KEMET EC2/EE2 miniature signal relays offer a ... EE2-3(1)NUX-L 3.0 Surface mount, High solder joint reliability Tape on Reel EE2-4.5(1)NUX-L 4.5 Surface mount, High solder joint reliability Tape on Reel ...
SMT Board Assembly Process Guide - Intel
www.intel.comHere is a method for placing TC’s to measure SMT joint temperatures: Before the component is soldered to the board, drill a small hole through the pad of the joint to be measured Insert the thermocouple from the bottom of the board Hold the thermocouple tip flush with the top surface of the board
Guidelines for Design, Selection and Application of ...
www.ipc.orgIPC-HDBK-830A Guidelines for Design, Selection and Application of Conformal Coatings Developed by the Conformal Coating Handbook Task Group (5-33c) of
Tow-Pro Wiring Kit - Ford Ranger / Everest
www.redarc.com.auSolder the wires to the Butt Splice. Ensure that a good connection is made. Wait for the Butt Splice to cool, slip the Heatshrink over the joint and heat. Reconnect the 16-way connector (1). Keep heatshrink away from joint until after soldering is complete and cooled. Proceed to Step 30. Page 13 of 3 12 34
MSL Ratings and Reflow Profiles (Rev. A) - TI.com
www.ti.comsolder paste is starting its activity and cleaning process of all surfaces involved into the later solder joint begins. • Liquidous temperature (TL) for lead-free soldering - this is approximately 217°C. ... Wave soldering is an older technology that is frequently used for soldering through-hole components or the larger pitch packages, such ...
Metal Film Resistors, Axial, Military/Established ...
www.vishay.com(3) Hot solder dipped leads. (4) Tolerance of ± 0.1 % is not applicable to characteristics K. STANDARD ELECTRICAL SPECIFICATIONS GLOBAL MODEL MIL-PRF-55182 STYLE MIL SPEC. SHEET POWER RATING P70 °C W POWER RATING P125 °C W TOLERANCE (4) ± % MAXIMUM WORKING VOLTAGE (2) V RESISTANCE RANGE Ω TEMPERATURE …