Serial LVDS High-Speed ADC Interface - Xilinx
deserializer components (ISERDESE2 primitives) in 7 series FPGAs to interface with analog-to-digital converters (ADC) with serial, low-voltage, differential signalling (LVDS) outputs. The associated reference design illustrates a basic LVDS interface connecting a Kintex™-7 FPGA to an ADC with high-speed, serial LVDS outputs.
Download Serial LVDS High-Speed ADC Interface - Xilinx
Information
Domain:
Source:
Link to this page:
Documents from same domain
Zynq-7000 All Programmable SoC Software …
www.xilinx.comZynq-7000 All Programmable SoC Software Developers Guide UG821 (v12.0) September 30, 2015
Zynq-7000 SoC Data Sheet: Overview (DS190) - All …
www.xilinx.comZynq-7000 SoC Data Sheet: Overview DS190 (v1.11.1) July 2, 2018 www.xilinx.com Product Specification 3 Programmable Logic Xilinx 7 Series Programmable Logic
7 Series FPGAs Data Sheet: Overview (DS180)
www.xilinx.com7 Series FPGAs Data Sheet: Overview DS180 (v2.6) February 27, 2018 www.xilinx.com Product Specification 2 Spartan-7 FPGA Feature Summary Table 2: Spartan-7 FPGA Feature Summary by Device
Accelerating OpenCV Applications with Zynq-7000 …
www.xilinx.comReference Design XAPP1167 (v3.0) June 24, 2015 www.xilinx.com 2 The design flow for this application note generally follows the steps below: 1. Develop and execute an OpenCV application on Desktop.
Product Obsolete/Under Obsolescence …
www.xilinx.comEfficient Shift Registers, LFSR Counters, and Long Pseudo-Random Sequence Generators 2 XAPP 052 July 7,1996 (Version 1.1) Divide-By 5 to 16 Counter in Two CLBs
XILINX ARTIX-7 FPGAS: A NEW PERFORMANCE …
www.xilinx.comKey Capability Overview . Smallest Package • Low-cost, wire-bond, chip-scale BGA packaging • Available in a 10x10mm package for maximum system integration
Platform Flash In-System Programmable …
www.xilinx.comPlatform Flash In-System Programmable Configuration PROMs DS123 (v2.19) June 6, 2016 www.xilinx.com Product Specification 2 R When the FPGA is in Master Serial mode, it generates a
Spartan-3AN FPGA Family Data Sheet (DS557) - Xilinx
www.xilinx.comSpartan-3AN FPGA Family: Introduction and Ordering Information DS557 (v4.2) June 12, 2014 www.xilinx.com Product Specification 3 Architectural Overview
Xilinx XAPP1113 Designing Efficient Digital Up and …
www.xilinx.comIntroduction XAPP1113 (v1.0) November 21, 2008 www.xilinx.com 2 R • DDC design files for multi-channel MRI, targeting both Virtex-5 and Spartan®-DSP
Xilinx DS060 Spartan and Spartan-XL FPGA …
www.xilinx.comSpartan and Spartan-XL FPGA Families Data Sheet 2 www.xilinx.com DS060 (v2.0) March 1, 2013 Product Specification R Product Obsolete/Under Obsolescence General Overview Spartan series FPGAs are implemented with a regular, flex-
Related documents
1747-IN063C-EN-P, Universal Serial Bus (USB) to DH-485 ...
literature.rockwellautomation.comUniversal Serial Bus (USB) to DH-485 Interface Converter 7 Publication 1747-IN063C-EN-P - January 2006 Install the Drivers Before using the 1747-UIC, you must install drivers for both the 1747-UIC interface converter and the USB serial port. To install the drivers: 1. If you have RSLinx version 2.42, or higher, the 1747-UIC drivers are included
AXI IIC Bus Interface v2 - Xilinx
japan.xilinx.comThe LogiCORE™ IP AXI IIC Bus Interface connects to the AMBA® AXI specification and provides a low-speed, two-wire, serial bus interface to a large number of popular devices. This product specification defines the architecture, hardware (signal) interface, software (register) interface, and parameterization options for the AXI IIC Bus
MCP23008/MCP23S08 8-Bit I/O Expander with Serial Interface ...
ww1.microchip.comtemperature, serial bus frequency, etc.) must be met to ensure proper operation. 1.3 Serial Interface This block handles the functionality of the I2C (MCP23008) or SPI (MCP23S08) interface protocol. The MCP23X08 contains eleven registers that can be addressed through the serial interface block ( Table 1-2): TABLE 1-2: REGISTER ADDRESSES
AN0062: Programming Internal Flash Over the Serial Wire ...
www.silabs.com1 Debug Interface Overview 1.1 Serial Wire Debug Serial Wire Debug (SWD) is a two-wire protocol for accessing the ARM debug interface. It is part of the ARM Debug Interface Specification v5 and is an alternative to JTAG. The physical layer of SWD consists of two lines: • SWDIO: a bidirectional data line • SWCLK: a clock driven by the host
MIPI Alliance Specification for Camera Serial Interface 2 ...
caxapa.ruCamera Serial Interface 2 (CSI-2) Draft Version 1.01.00 Revision 0.04 – 2 April 2009 Further technical changes to this document are expected as work continues in the Camera Working Group . Version 1.01.00 r0.04 2-Apr-2009 DRAFT MIPI Alliance Specification for CSI-2
Serial Control Interface Standard (Rev 1.0) - Analog Devices
wiki.analog.comThe defined serial interface shall consist of SCLK, SDIO, CSB and SDO. 4.2.1 CSB CSB is the chip select, an active low signal that selects the slave device with which the master intends to communicate. Typically, there is a dedicated CSB between the master and each slave. CSB is always driven by the master.
MPC5121e Serial Peripheral Interface (SPI)
www.nxp.comMPC5121e Serial Peripheral Interface (SPI), Rev. 0 Description of the SPI module 2 Freescale Semiconductor diodes (LCD), analog-to-digital converter subsystems, etc. The SPI is a very simple synchronous serial data, master/slave protocol based on four lines:
SPI (Serial Peripheral Interface) NAND Flash Memory
www.endrich.comThis low-pin-count NAND Flash memory follows the industry-standard serial peripheral interface, and always remains the same pinout from one density toanother . The command sets resemble common SPI-NOR command sets, modified to handle NAND specific functions and added new features. GigaDevice SPI NAND is an easy-to-integrate
Lab Configuring Basic Switch Settings (Solution)
sites.radford.eduNotice that the VLAN 99 interface is in the down state even though you entered the no shutdown command. The interface is currently down because no switch ports are assigned to VLAN 99. c. Assign all user ports to VLAN 99. S1(config)# interface range f0/1 – 24,g0/1 - 2 S1(config-if-range)# switchport access vlan 99 S1(config-if-range)# exit