SMALL FRAGMENT SYSTEM
THE SMALL FRAGMENT STANDARD SYSTEM The Small Fragment Standard System contains the 2.7 mm, 3.5 mm and 4.0 mm implants and related ... versal drill guide on pages 14 and 15 for more detail) ... DePuy Synthes product dimensions are proprietary. The precision design of DePuy Synthes products is very important for
Download SMALL FRAGMENT SYSTEM
Information
Domain:
Source:
Link to this page:
Documents from same domain
CODMAN CERTAS Plus Programmable Valve and …
synthes.vo.llnwd.netProvides the fl exibility, versatility and confi dence to manage the needs of the hydrocephalus patient. CODMAN CERTAS® Plus Programmable Valve and CODMAN CERTAS® Tool Kit ORDERING INFORMATION
LCP Locking Compression Plate - synthes.vo.llnwd.net
synthes.vo.llnwd.netLCP Locking Compression Plate Surgical Technique DePuy Synthes 1 Table of Contents Introduction LCP Locking Compression Plate 2 LCP Metaphyseal Plates 4 AO Principles 5 ...
LCP Locking Compression Plate - synthes.vo.llnwd.net
synthes.vo.llnwd.net4 DePuy Synthes LCP Locking Compression Plate Surgical Technique LCP Metaphyseal Plates. For extra-articular fractures. LCP combi-holes allow uncompromising
3.5 mm LCP Hook Plate. Part of the Synthes locking ...
synthes.vo.llnwd.netSharp hooks Aid in placement of the plate 3.5 mm LCP Hook Plate. Part of the Synthes locking compression plate (LCP) system. 2 Synthes 3.5 mm LCP Hook Plate Technique Guide
Universal and powerful battery system for a variety …
synthes.vo.llnwd.netColibri II Instructions for Use DePuy Synthes 5 2 Do not reuse Products intended for single use must not be reused. Reuse or reprocessing (e.g. cleaning and resteril-
Inventory Control Form - synthes.vo.llnwd.net
synthes.vo.llnwd.netImplants Date: Hospital: Surgeon: Procedure: Case Information (eg, Case ID): Inventory Control Form Small Fragment Locking Compression Plate (LCP®) System 3.5 mm Locking Screws, self-tapping, with StarDriveTM Recess
Inventory Control Form - Limelight Networks
synthes.vo.llnwd.netDate: Hospital: Surgeon: Procedure: Implants Patient Information: J3925-K 6/11 Inventory Control Form Locking Small Fragment–LCP 2.7 mm Cortex Screws,
Inventory Control Form - synthes.vo.llnwd.net
synthes.vo.llnwd.netImplants (cont’d) J8493-H 3/13 2.4 mm Cortex Screw, self-tapping, with T8 StarDrive recess Length 201.756 6 mm 201.758 8 mm 201.760 10 mm 201.762 12 mm 201.764 14 mm
2.4 mm LCP Distal Radius System - Limelight …
synthes.vo.llnwd.net2.4 mm LCP Distal Radius System. A comprehensive plating system to address a variety of fracture patterns. * For long volar plates refer to Synthes Dia-Meta Volar Distal Radius Plate …
For Medial High Tibial Osteotomies TomoFix™ …
synthes.vo.llnwd.netTomoFix Medial High Tibial Plate (MHT) Surgical Technique DePuy Synthes 1 Table of Contents Introduction Indications and Contraindications 4 General Remarks 5 Surgical Technique Open Wedge Surgical Technique 6
Related documents
Microwave Drawer : SMD2470AS, SMD2470AH, SMD3070AS ...
files.sharpusa.com• • Dimensions that are shown in Figure 1 (for 24") or Figures 4 and 5 (for 30") must be used. Given dimensions provide ... This drawing represents a typical standard cabinet. If installed in custom ... pre drill the cabinet using a 1/16" bit. See Figure 10A. 5.
This Document provide North American Bluebird Society
www.nabluebirdsociety.orgDrill two 1 3/8” hole & chisel sides flat to oval ” the bottom 3/4” Drill hole through the front board and the side of the door to latch door closed. Floor corners cut for drainage Floor The roof will overhang the front ~6” – 6 ½” and both sides ~2” when completed. The roof will have a 20 deg back to front slope.
DRILLED SHAFTS - South Dakota Department of …
dot.sd.govConcrete Mix Requirements 28 Day Compressive Strength = 4500 psi Slump Range: 6” to 8” for free fall or tremie method – 7” to 9” for concrete pumped through a tremie. – In addition, slump shall be maintained above 4” for 4 hours
Greenfield Industries
www.gfii.comCreated Date: 3/7/2011 12:30:21 PM
DD421 DEVELOPMENT DRILL - Sandvik Mining and Rock …
www.rocktechnology.sandvik*) Replaces standard feature 3. SANDVIK DD421 - DEVELOPMENT DRILL OPTIONAL FEATURES AND PACKAGES Rock drill *Type of rock drill RDX5 instead of RD525 RD520 instead of RD525 Feed *Feed length *Telescopic feed Rod retainer Two rods system 14’, 16’ TFX6/12, TFX8/14, TFX10/16 TRR1 incl. safety wire, add 35 mm length of the feed
RIELLO 40 SERIES - Weil-McLain
www.weil-mclain.comthe heating unit. Then drill ¼ inch (6.5mm) holes through the front plate of the unit, using marks as a guide. C) Install two short BOLTS (1) through the front plate of the heating unit from the inside, and secure on the outside using the two special CHROME NUTS (2). D) Follow item D from METHOD 1.