TEA5767HN Low-power FM stereo radio for handheld …
PILFIL 19 pilot detector low-pass filter n.c. 20 not connected n.c. 21 not connected VAFL 22 left audio frequency output voltage VAFR 23 right audio frequency output voltage TMUTE 24 time constant for soft mute MPXO 25 FM demodulator MPX signal output Vref 26 reference voltage TIFC 27 time constant for IF center adjust LIMDEC1 28 decoupling IF ...
Download TEA5767HN Low-power FM stereo radio for handheld …
Information
Domain:
Source:
Link to this page:
Documents from same domain
AT Commands Reference Guide - SparkFun …
www.sparkfun.comAT Commands Reference Guide 80000ST10025a Rev. 0 - 04/08/06 Reproduction forbidden without Telit Communications S.p.A. written authorization - All …
DS1307 64 x 8 Serial Real-Time Clock
www.sparkfun.com1 of 12 100101 FEATURES Real-time clock (RTC) counts seconds, minutes, hours, date of the month, month, day of the week, and year with …
Advanced User Manual - SparkFun Electronics
www.sparkfun.comusage information and a summary of common commands refer to the Install Guide for a given product. Version 4.77 August 27, 2009 Roving Networks reserves the right to make corrections, modifications, and changes to its products, documentation and services ... Advanced User Manual.
Preliminary Product Specification v1 - SparkFun Electronics
www.sparkfun.comRevision 1.0 Page 3 of 75 nRF24L01+ Preliminary Product Specification Writing Conventions This product specification follows a set of typographic rules that make s the document consistent and easy
Single chip 2.4 GHz Transceiver nRF24L01
www.sparkfun.comPRELIMINARY PRODUCT SPECIFICATION nRF24L01 Single Chip 2.4 GHz Radio Transceiver Nordic Semiconductor ASA - Vestre Rosten 81, N-7075 Tiller, Norway - Phone +4772898900 - …
XBee /XBee-PRO RF Modules - SparkFun Electronics
www.sparkfun.comThe XBee®/XBee-PRO® RF Module was designed to mount into a receptacle (socket) and there-fore does not require any soldering when mounting it to a board. The XBee Development Kits con-tain RS-232 and USB interface boards which use two 20-pin receptacles to receive modules.
GSM/GPRS Module - SparkFun Electronics
www.sparkfun.comThis document gives an overview of the LinkSprite GSM/GPRS module: a miniature, single-side board, quad-band GSM 850/EGSM 900/DCS 1800/PCS 1900 module, ready for integration in various kinds of Fix wireless phones and other wireless devices.
16-Channel Constant-Current LED Driver
www.sparkfun.comA6282 Description The A6282 device is designed for LED display applications. This CMOS device includes an input shift register, accompanying data latches, and 16 MOS constant current sink drivers.
+3.3V Low Power Half-Duplex RS-485 Transceivers with ...
www.sparkfun.com10/15/02 SP3481/3485 Low Power Half-Duplex RS485 Transceivers © Copyright 2000 Sipex Corporation 2 SPECIFICATIONS T AMB = T MIN to T MAX and V CC = +3.3V ± 5% ...
XBee /XBee-PRO RF Modules - SparkFun Electronics
www.sparkfun.comDigi International Inc. 11001 Bren Road East Minnetonka, MN 55343 877 912-3444 or 952 912-3444 http://www.digi.com XBee®/XBee-PRO® RF Modules XBee®/XBee-PRO® RF ...
Related documents
CIRCUITS LABORATORY EXPERIMENT 9 Operational Amplifiers
classes.engineering.wustl.eduFigure 9.4: Operational amplifier connected as a voltage follower voltage follower of Figure 9.4. The input voltage is Vi,. The virtual short forces v-= v+ and, therefore, Vo = Vi. Hence, it is termed a voltage follower. Now you may be thinking that this is a circuit that serves no function since the output voltage merely equals the input voltage.
A Ham's Guide to RFI, Ferrites, Baluns, and Audio ...
www.audiosystemsgroup.comA common mode signal is one that places equal voltage on all conductors – that is, the voltage be-tween the two ends of the cable are different, but there is no voltage between the conductors. An-tenna action produces a common mode voltage and current along a cable. The antenna current in-duced on audio and video wiring is a common mode ...
TDA8954 2 × 210 W class-D power amplifier - NXP
www.nxp.comThe TDA8954 is a stereo or mono high-efficiency Class D audio power amplifier in a single IC featuring low power dissipation. It is designed to deliver up to 2 × 210 W into a mono Bridge-Tied Load (BTL) application. sound quality comparable to that associated with Class AB amplification. The amplifier operates over a wide supply voltage range ...
Datasheet - STM32H742xI/G STM32H743xI/G - 32-bit Arm ...
www.st.com• Voltage scaling in Run and Stop mode (6 configurable ranges) • Backup regulator (~0.9 V) • Voltage reference for analog peripheral/VREF+ • Low-power modes: Sleep, Stop, Standby and VBAT supporting battery charging Low-power consumption • VBAT battery operating mode with charging capability • CPU and domain power state monitoring pins
CONTAINS TWO SEPARATE AUDIO SYSTEMS - Elenco
www.elenco.comincrease the power of the audio signal received from either detector to a power level capable of driving the speaker. The audio amplifier is IC or transistor version. Section 2 includes the AM detector circuit and the AGC (automatic gain control) stage. The AM detector converts the amplitude modulated IF (intermediate frequency) signal to a low ...
Audio Amplifier Circuit - UC Santa Barbara
web.ece.ucsb.eduAudio Amplifier Circuit Overview In the first part of lab#1 you will construct a low-power audio amplifier/speaker driver based on the LM386 IC from National Semiconductor. The audio amplifier will be a self-contained, battery-operated component. In the …
TECHNICAL DATA PowerMatch PM8500N configurable power …
assets.bose.comThe Bose PowerMatch PM8500N configurable professional power amplifier provides concert-quality sound with a high level of scalability and configurability. The PM8500N offers multiple channel and power options, an integrated audio DSP, front panel interface, USB connection, and Ethernet-based network configuration, control and monitoring.
AT-LP60X User Manual - Audio-Technica
www.audio-technica.com*An audio adapter (sold separately) may be required to connect the RCA audio cable to the line input jack of the PC sound card. Connecting the device Align the settings for the pre-amplifier selector switch and connect the RCA audio cable to an input jack that is compatible with the connectable equipment you are using (amplifier,
Description Pin Assignments - Adafruit Industries
cdn-shop.adafruit.comFor the best power on/off pop performance, the amplifier should be set in the shutdown mode prior to power on/off operation. Under Voltage Lock-Out (UVLO) The PAM8302A incorporates circuitry to detect low on or off voltage. When the supply voltage drops to 2.1V or below, the PAM8302A goes into